Locks XNarrow_DL1200 DL1300 PDL1300_WI1458D.22_INST Installation Instructions Inst Dl1200

User Manual: Locks Installation instructions Mayflower Sales - Alarm Lock Systems

Open the PDF directly: View PDF .
Page Count: 8

1

DL1200 - DL1300 - PDL1300

NARROW STILE ACCESS LOCKS

MOUNTING AND INSTALLATION

INSTRUCTIONS

WI1458D 10/06

GENERAL DESCRIPTION

The DL1200, DL1300 and PDL1300 are manually program-

mable narrow stile entry trim for Adams Rite® 4710, 4730 and

4900 deadlatch locks, and 1850, 1950, 4070, MS1850S and

MS1950S series deadbolts for narrow stile aluminum doors*.

The DL1200, DL1300 and PDL1300 will retract the existing

Adams Rite® latch when an access code is entered (or a cre-

dential is presented) and the lever is pressed down (or the

turnpiece turned). The trim is designed to operate with any

Adams Rite® interior device such as a "pushpaddle" or lever.

Because Adams Rite® trim exists on the inside, the "hold-back

feature remains operational for a continuous unlatched func-

tion (see Adams Rite® instructions). Entering a passage

mode function code activates latched passage mode (device

is unlocked but the lever or turnpiece is engaged continuously)

until another passage mode function code is entered, re-

locking the trim. All locks are equipped with a mechanical

metal key override. See OI310, OI311 or OI312 for program-

ming information.

MECHANICAL FEATURES

The overall enclosure housing is 14 3/8" inches high, 1 5/8"

inches deep and 1¾" inches wide. The trim is through-bolted

to the stile of the door (using four #10 screws) and are se-

cured on the interior side of the door. Supported stile thick-

ness is 1¾".

•DL1200 Series supports 100 users, fingertip/keypad pro-

grammable

•DL1300 Series supports 2000 users and includes 40,000

event audit trail and 500 event schedule. Keypad or PC

programmable

•PDL1300 Series supports 2000 PIN or Prox users and

includes 40,000-event audit trail and 500 event schedule.

Keypad or PC programmable

•Aluminum door retrofit outside trim for Adams Rite®

1850, 1950, 4710, 4070, 4730, 4900, MS1850S and

MS1950S Series locks

•Familiar Trilogy® programming & electronics

•All-metal, vandal-resistant 12-button keypad supports 3-6

digit PIN codes (3-5 digits on the DL1200), and multilevel

user hierarchy (master, manager, supervisor and basic

users)

•Keypad or PC programmable (see model information).

Quickly and easily add or delete users and enter

345 Bayview Avenue

Amityville, New York 11701

For Sales and Repairs 1-800-ALA-LOCK

For Technical Service 1-800-645-9440

Publicly traded on NASDAQ Symbol: NSSC

© ALARM LOCK 2006

*Adams Rite Manufacturing Co., Pomona, CA. www.adamsrite.com. All products, product

names and services described in this manual are for identification purposes only and may be

trademarks of their respective companies.

"passage mode", service codes, group lock-out &

group-enable

•HID Prox ID cards, keyfobs and prox tags supported in

PDL1300 series which features built-in Prox reader

(High security applications can require use of both PIN

code plus Prox ID card for access)

•Real time clock and PC programmable automatic lock/

unlock scheduling for 500 events (1300 Series models)

•Wide weatherproof operating range from -31 to 151ºF

(-35 to 66C)

•Provides 100,000 operations using off-the-shelf long

life DL123A lithium batteries, and includes audible and

visual low battery alert

•Non-handed; fully field-reversible

•Mechanical key override; interchangeable cores sup-

ported (Corbin/Russwin, Yale, Schlage, Medeco)

•Mortise Cylinder, 1¼" supplied (supports 1-1/8", 1¼",

1-3/8" and 1½"

•Compact styling 14-3/8"H x 1-5/8"D x 1¾"W

•Backsets 31/32",1-1/8" and 1½"; stile thickness 1¾"

TABLE OF CONTENTS

GENERAL DESCRIPTION .............................................1

MECHANICAL FEATURES ............................................1

MOUNTING AND INSTALLATION .................................2

INSTALL CYLINDER .................................................3

VERIFY HAND ...........................................................3

INSTALL LEVER ........................................................4

INSERT INTERFACE CYLINDER .......................4

INSTALL LOCK ....................................................5

INSTALL BATTERIES ..........................................6

TEST OPERATION .........................................................7

NAPCO LIMITED WARRANTY ......................................8

2

MOUNTING AND INSTALLATION

For factory prepped doors, use dimensions shown. Di-

mensions are referenced from center of 1¼" cylinder hole.

The Adams Rite® lock determines the backset.

When mounting the new Adams Rite® locks:

•Do not install the outside cylinder -- this trim replaces it;

•Do not install the faceplate (access to the cylinder set

screw in the lock is required during mounting and instal-

lation).

Mechanical Override Cylinder Cams

The DL1200 and DL/PDL1300 trim requires the use of an

oval Alarm Lock cam (supplied with cylinder). For other

manufacturers, please see the charts below.

Cylinder Collars:

The DL1200 and DL/PDL1300 can use a 1-1/8" & 1¼" mor-

tise cylinder without the use of a collar (1¼" requires two

plastic spacers, supplied). For cylinders longer than 1¼" a

collar is required.

Order collars from an Alarm Lock distributor.

Template (use WI1459)

Backset is determined by

the Adams Rite lock

Corbin-Russwin HW1344

Marks HW1346

Arrow HW1348

Schlage HW1349

Cams for Standard Mortise Cylinders

Sargent HW1348

Cams for IC Mortise Cylinders

Best* HW1343

Corbin-Russwin HW1345

Medeco HW1347

Schlage HW1350

Yale HW1351

*Will be supplied together with Best IC Housing (HW1352)

Cylinder Length Collar P/N

1-3/8 HW1331

1-½ HW1342

Cam for Mechanical Override Cylinder

3

Install Cylinder

1. Install Cylinder if not already installed at the fac-

tory. Screws A & B (see Fig. 1) are correctly set at

factory. If it is difficult to screw in the cylinder, loosen

the two screws near the actuator (A) one turn. If you

find the cylinder is still difficult to screw in, then loosen

the other screws (B) one turn. Do not loosen the

screws all the way or it may be difficult to replace

them properly! Note: The trim is manufactured to

use a 1-1/8" or 1¼" Alarm Lock mortise cylinder with a

HW-1302 cam. If the cylinder that will be used is

longer than 1¼", a collar must be utilized. Please see

the collar information on the previous page.

1a. Insert key half-way into the cylinder, then screw it

in. See Fig. 1a. If cylinder will not seat flush, the cylin-

der back stop screw may require loosening. Cylinders

that are longer than 1¼"

will require a collar, which

will stick out from the sur-

face when correctly in-

stalled. Please see the

cylinder information on

the previous page.

1b. After the cylinder is screwed in all the way, center

the keyway toward the bottom (see Fig. 1b). If an

interchangeable core cylinder is utilized, then center

the interface toward the bottom. Tighten the screws

that were loosened in step 1.

1c. Remove the key. Use a 1/16" hex wrench to screw

the cylinder back stop screw in fully. (See Fig. 1c)

The key should now only rotate counterclockwise.

NOTE: To remove cylinder, reverse steps 1a-1c.

Setting the Door "Hand"

2. With the key always on the outside, the door hand is

generally determined by the location of the hinges--

hinges are either inside or outside. See Fig. 2.

2a. Setting Hand of Interface Cylinder/Adapter

Refer to Fig. 2a to determine if changing the hook

cam lever is necessary. If changing the hook cam

lever is necessary, refer to Fig. 2b (on next page).

Fig. 1: Install Cylinder if not already installed at the factory

A

B

Fig. 1b: Center keyway toward bottom

Fig. 1c: Use 1/16" hex wrench to screw in

the cylinder back stop screw

RIGHT HAND LEFT HAND

STANDARD RH LH

REVERSE RHR LHR

Fig. 2: Cross Section Top View -- Door Hand

(Hinges)

(Keys) (Keys)

STANDARD

REVERSE

Cylinder back stop

screw

Fig. 1a: Insert key 1/2 way

into cylinder and screw in

Fig 2a: Correct orientation for Interface cylinder

and hook cam (LH and RH)

LH/LHR RH/RHR

4

•Remove the retaining ring with a screwdriver.

•Remove the pin, then flip over the hook cam lever.

•Re-install the retain-

ing ring displayed in

Fig. 2c (arrow).

Install the Lever

3. Install the lever with proper orientation for the lock/

door hand used. Tighten the set screw using a 1/8" hex

wrench (see Fig. 3).

IMPORTANT! The

top of the set screw

must be at (or below)

lever surface. If not,

check to ensure the

lever is fully pushed

toward the trim.

3a. Install the Adams Rite® product as indicated by the

Adams Rite® door prep guidelines and instructions.

•If a new installation, the face place must NOT be

installed at this time.

•If a retrofit installation,

remove the face plate.

Prepare the Door For

"Through-Bolting"

4. Place template (WI1459) as

shown. Important: Place the

template on top of existing cyl-

inder hole and parallel to the

door edge.

4a. Drill completely through the

door for through-bolting the

four mounting holes.

•IMPORTANT!--Drill the holes STRAIGHT

THROUGH the door, or the through-bolts will

not fit in the lock! THIS IS ESSENTIAL! Drill

slowly and STRAIGHT through the door.

•Reposition the template as often as needed until

it is placed correctly.

Insert the Interface Cylinder

5. Loosen the set screw, then remove the outside

cylinder (if present--See Fig. 6).

5a. Push in latch and hold latch in all the way.

5b. While holding in the latch, carefully insert the interface

cylinder assembly into the cylinder hole. The hook

must be in front of the latch retractor and pass through

the notch in the lock case (see Fig. 6b).

Fig. 6a: Push latch in and hold

Push in

latch during

interface

cylinder

installation

Fig 2b: Remove the retaining ring

with a small screwdriver...

...remove the pin, then flip over hook cam

lever.

Fig. 4: Template (WI1459)

through-bolt holes (circled)

Fig. 2c: Re-install the retaining ring

Fig. 3: Tighten lever set screw

with 1/8" hex wrench

Fig. 6: Loosen set screw before removing the

old interface cylinder (if present)

Old interface

cylinder

Set screw

Interface cylinder

Fig. 6b: While holding latch in, place hook in front of

the latch retractor and through the notch

Notch

Hook

5

5c. The interface cylinder must be centered and posi-

tioned flush with (or slightly below) the surface of the

door (see Fig. 7).

5d. With the interface cylinder HELD SECURELY in its

correct position, tighten the set screw, securing the

interface cylinder to the lock (see Fig. 7a).

Important! If the interface cylinder is not parallel to

the door after tightening the set screw, then you must

verify that the original Adams Rite® lock body was

originally installed correctly (installed square to the

door). Failure to ensure the interface cylinder is in-

stalled correctly could cause lock binding or improper

operation of the lock mechanism.

5e. Install the latch face plate.

Install Lock

6. Install the DL lock onto the door by aligning the two

posts on the front of the interface cylinder with the two

corresponding holes in the back of the DL lock. Lift the

tailpiece slightly to ensure the tailpiece enters the slot

of the interface cylinder.

6a. Secure the DL lock to the door with four through-

door mounting screws and two door plates. Place a

door plate on top of a pair of mounting holes and

loosely secure lock from the inside of the door. Snug

all four mounting screws before final tightening. Do not

over-tighten.

6b. Cover door plates with decorative plate covers by

sliding them from top to bottom on door plates.

Fig. 7: Position the interface cylinder

Fig. 7a: Tighten the interface cylinder set screw

Fig. 9: Secure lock to door -- loosely at first

Door plate

Fig. 9a: Slide down to install decorative plate covers

Fig. 7b: Install the latch face plate

Fig. 8: Install lock onto the door

6

Install Batteries

7. Insert key in cylinder and turn counterclockwise. This

will allow access to the battery compartment screw.

With the supplied 5/64" Allen wrench, loosen the bat-

tery cover screw only until the battery cover is able

to slide off. Remove the battery pack.

Note: Loosening the battery cover screw in excess of

what is necessary may interfere with the mechanical

operation of the key override assembly. Although the

lock will not be damaged, when the key is removed the

assembly may not function until the battery cover screw

is re-tightened.

7a. FOR NEW INSTALLATIONS: Refer to program-

ming instructions (OI310, OI311 or OI312) for spe-

cific instructions for "First Time Startup" and

"Change Factory Master Code" before connecting

the battery.

The lock must be powered up correctly (and have

its factory Master Code changed) or erratic lock be-

havior can result.

7b. Install batter y pack into the battery compartment.

Neatly push all wiring inside the compartment. Hold-

ing battery in place, slide cover back on.

See Fig. 11.

7c. While turning key counterclockwise again, allow-

ing access to the battery cover screw, tighten the

battery cover screw fully. Turn the key clockwise and

remove.

Test operation: See next page.

Fig. 11: Install the battery pack

Fig. 12: Turn key counterclockwise and

tighten the cover screw.

Fig. 10: Loosen battery cover screw only until the battery

cover is able to slide off

7

TEST LOCK OPERATION

Before testing, be sure the lock has been powered-

up using the specific instructions in the OI310,

OI311 or OI312 manuals.

1. With key removed, ensure that the lever CAN ONLY

be pushed down (not up), and the latch should NOT

retract while pushing down the lever with the key out.

2. Release lever. Insert key and turn key fully counter-

clockwise.

3. Depress the lever and the latch should retract.

4. Turn key clockwise and remove key.

The lever must not retract the latch when pressed

down.

5. While pressing the default access code on the lock

keypad (press "1 2 3 4 5" on the DL1200 and press

"1 2 3 4 5 6" on the DL/PDL1300), note the following:

•For each number key pressed, the red LED lights.

•When the "5" button is pressed (or the "6" button

on the DL/PDL1300):

1. The green LED flashes for approximately 5

seconds, and then

2. The latch is retracted when the lever is pushed

down

6. Test the exit device mounted inside (paddle / egress

bar, etc.) and confirm it is operating correctly.

SEE PROGRAMMING INSTRUCTIONS OI310,

OI311 or OI312 FOR KEYPAD PROGRAMMING

INFORMATION.

Latch

retracted

Test Step 1

Test Step 2

Test Step 3

Test Step 5

Test Step 4

8

ALARM LOCK SYSTEMS, INC. (ALARM LOCK)

warrants its products to be free from manufacturing

defects in materials and workmanship for 24 months

following the date of manufacture. ALARM LOCK will,

within said period, at its option, repair or replace any

product failing to operate correctly without charge to

the original purchaser or user.

This warranty shall not apply to any equipment, or

any part thereof, which has been repaired by others,

improperly installed, improperly used, abused, altered,

damaged, subjected to acts of God, or on which any

serial numbers have been altered, defaced or

removed. Seller will not be responsible for any

dismantling or reinstallation charges.

THERE ARE NO WARRANTIES, EXPRESS OR

IMPLIED, WHICH EXTEND BEYOND THE

DESCRIPTION ON THE FACE HEREOF. THERE IS

NO EXPRESS OR IMPLIED WARRANTY OF

MERCHANTABILITY OR A WARRANTY OF

FITNESS FOR A PARTICULAR PURPOSE.

ADDITIONALLY, THIS WARRANTY IS IN LIEU OF

ALL OTHER OBLIGATIONS OR LIABILITIES ON

THE PART OF ALARM LOCK.

Any action for breach of warranty, including but not

limited to any implied warranty of merchantability, must

be brought within the six months following the end of

the warranty period. IN NO CASE SHALL ALARM

LOCK BE LIABLE TO ANYONE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGES

FOR BREACH OF THIS OR ANY OTHER

WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE

LOSS OR DAMAGE IS CAUSED BY THE SELLER'S

OWN NEGLIGENCE OR FAULT.

In case of defect, contact the security professional

who installed and maintains your security system. In

order to exercise the warranty, the product must be

returned by the security professional, shipping costs

prepaid and insured to ALARM LOCK. After repair or

replacement, ALARM LOCK assumes the cost of

returning products under warranty. ALARM LOCK

shall have no obligation under this warranty, or

otherwise, if the product has been repaired by others,

improperly installed, improperly used, abused, altered,

damaged, subjected to accident, nuisance, flood, fire

or acts of God, or on which any serial numbers have

been altered, defaced or removed. ALARM LOCK will

not be responsible for any dismantling, reassembly or

reinstallation charges.

This warranty contains the entire warranty. It is the

sole warranty and any prior agreements or

representations, whether oral or written, are either

merged herein or are expressly cancelled. ALARM

LOCK neither assumes, nor authorizes any other

person purporting to act on its behalf to modify, to

change, or to assume for it, any other warranty or

liability concerning its products.

In no event shall ALARM LOCK be liable for an

amount in excess of ALARM LOCK's original selling

price of the product, for any loss or damage, whether

direct, indirect, incidental, consequential, or otherwise

arising out of any failure of the product. Seller's

warranty, as hereinabove set forth, shall not be

enlarged, diminished or affected by and no obligation

or liability shall arise or grow out of Seller's rendering

of technical advice or service in connection with

Buyer's order of the goods furnished hereunder.

ALARM LOCK RECOMMENDS THAT THE ENTIRE

SYSTEM BE COMPLETELY TESTED WEEKLY.

Warning: Despite frequent testing, and due to, but

not limited to, any or all of the following; criminal

tampering, electrical or communications disruption, it is

possible for the system to fail to perform as expected.

ALARM LOCK does not represent that the product/

system may not be compromised or circumvented; or

that the product or system will prevent any personal

injury or property loss by burglary, robbery, fire or

otherwise; nor that the product or system will in all

cases provide adequate warning or protection. A

properly installed and maintained alarm may only

reduce risk of burglary, robbery, fire or otherwise but it

is not insurance or a guarantee that these events will

not occur. CONSEQUENTLY, SELLER SHALL HAVE

NO LIABILITY FOR ANY PERSONAL INJURY,

PROPERTY DAMAGE, OR OTHER LOSS BASED

ON A CLAIM THE PRODUCT FAILED TO GIVE

WARNING. Therefore, the installer should in turn

advise the consumer to take any and all precautions

for his or her safety including, but not limited to, fleeing

the premises and calling police or fire department, in

order to mitigate the possibilities of harm and/or

damage.

ALARM LOCK is not an insurer of either the property

or safety of the user's family or employees, and limits

its liability for any loss or damage including incidental

or consequential damages to ALARM LOCK's original

selling price of the product regardless of the cause of

such loss or damage.

Some states do not allow limitations on how long an

implied warranty lasts or do not allow the exclusion or

limitation of incidental or consequential damages, or

differentiate in their treatment of limitations of liability

for ordinary or gross negligence, so the above

limitations or exclusions may not apply to you. This

Warranty gives you specific legal rights and you may

also have other rights which vary from state to state.

ALARM LOCK LIMITED WARRANTY