Locks XNarrow_DL1200 DL1300 PDL1300_WI1458D.22_INST Installation Instructions Inst Dl1200

User Manual: Locks Installation instructions Mayflower Sales - Alarm Lock Systems

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

DL1200 - DL1300 - PDL1300
NARROW STILE ACCESS LOCKS
345 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs 1-800-ALA-LOCK
For Technical Service 1-800-645-9440
Publicly traded on NASDAQ

MOUNTING AND INSTALLATION
INSTRUCTIONS

Symbol: NSSC

© ALARM LOCK 2006

WI1458D 10/06

GENERAL DESCRIPTION

The DL1200, DL1300 and PDL1300 are manually programmable narrow stile entry trim for Adams Rite® 4710, 4730 and
4900 deadlatch locks, and 1850, 1950, 4070, MS1850S and
MS1950S series deadbolts for narrow stile aluminum doors*.
The DL1200, DL1300 and PDL1300 will retract the existing
Adams Rite® latch when an access code is entered (or a credential is presented) and the lever is pressed down (or the
turnpiece turned). The trim is designed to operate with any
Adams Rite® interior device such as a "pushpaddle" or lever.
Because Adams Rite® trim exists on the inside, the "hold-back
feature remains operational for a continuous unlatched function (see Adams Rite® instructions). Entering a passage
mode function code activates latched passage mode (device
is unlocked but the lever or turnpiece is engaged continuously)
until another passage mode function code is entered, relocking the trim. All locks are equipped with a mechanical
metal key override. See OI310, OI311 or OI312 for programming information.

"passage mode", service codes, group lock-out &
group-enable
• HID Prox ID cards, keyfobs and prox tags supported in
PDL1300 series which features built-in Prox reader
(High security applications can require use of both PIN
code plus Prox ID card for access)
• Real time clock and PC programmable automatic lock/
unlock scheduling for 500 events (1300 Series models)
• Wide weatherproof operating range from -31 to 151ºF
(-35 to 66C)
• Provides 100,000 operations using off-the-shelf long
life DL123A lithium batteries, and includes audible and
visual low battery alert
• Non-handed; fully field-reversible
• Mechanical key override; interchangeable cores supported (Corbin/Russwin, Yale, Schlage, Medeco)
• Mortise Cylinder, 1¼" supplied (supports 1-1/8", 1¼",
1-3/8" and 1½"
• Compact styling 14-3/8"H x 1-5/8"D x 1¾"W

MECHANICAL FEATURES

The overall enclosure housing is 14 3/8" inches high, 1 5/8"
inches deep and 1¾" inches wide. The trim is through-bolted
to the stile of the door (using four #10 screws) and are secured on the interior side of the door. Supported stile thickness is 1¾".
• DL1200 Series supports 100 users, fingertip/keypad programmable
• DL1300 Series supports 2000 users and includes 40,000
event audit trail and 500 event schedule. Keypad or PC
programmable
• PDL1300 Series supports 2000 PIN or Prox users and
includes 40,000-event audit trail and 500 event schedule.
Keypad or PC programmable
®

• Aluminum door retrofit outside trim for Adams Rite
1850, 1950, 4710, 4070, 4730, 4900, MS1850S and
MS1950S Series locks
®

• Backsets 31/32",1-1/8" and 1½"; stile thickness 1¾"

TABLE OF CONTENTS
GENERAL DESCRIPTION .............................................1
MECHANICAL FEATURES ............................................1
MOUNTING AND INSTALLATION .................................2
INSTALL CYLINDER .................................................3
VERIFY HAND ...........................................................3
INSTALL LEVER........................................................4
INSERT INTERFACE CYLINDER .......................4

• Familiar Trilogy programming & electronics

INSTALL LOCK ....................................................5

• All-metal, vandal-resistant 12-button keypad supports 3-6
digit PIN codes (3-5 digits on the DL1200), and multilevel
user hierarchy (master, manager, supervisor and basic
users)

INSTALL BATTERIES..........................................6

• Keypad or PC programmable (see model information).
Quickly and easily add or delete users and enter

TEST OPERATION .........................................................7
NAPCO LIMITED WARRANTY ......................................8

*Adams Rite Manufacturing Co., Pomona, CA. www.adamsrite.com. All products, product
names and services described in this manual are for identification purposes only and may be
trademarks of their respective companies.

1

MOUNTING AND INSTALLATION
For factory prepped doors, use dimensions shown. Dimensions are referenced from center of 1¼" cylinder hole.
The Adams Rite® lock determines the backset.
When mounting the new Adams Rite® locks:
• Do not install the outside cylinder -- this trim replaces it;
• Do not install the faceplate (access to the cylinder set
screw in the lock is required during mounting and installation).
Mechanical Override Cylinder Cams
The DL1200 and DL/PDL1300 trim requires the use of an
oval Alarm Lock cam (supplied with cylinder). For other
manufacturers, please see the charts below.

Cams for Standard Mortise Cylinders
Corbin-Russwin

HW1344

Marks

HW1346

Arrow

HW1348

Sargent

HW1348

Schlage

HW1349

Backset is determined by
the Adams Rite lock

Cams for IC Mortise Cylinders
Best*

HW1343

Corbin-Russwin

HW1345

Medeco

HW1347

Schlage

HW1350

Yale

HW1351

Template (use WI1459)

*Will be supplied together with Best IC Housing (HW1352)

Cylinder Length

Collar P/N

1-3/8

HW1331

1-½

HW1342

Cylinder Collars:

The DL1200 and DL/PDL1300 can use a 1-1/8" & 1¼" mortise cylinder without the use of a collar (1¼" requires two
plastic spacers, supplied). For cylinders longer than 1¼" a
collar is required.
Order collars from an Alarm Lock distributor.

Cam for Mechanical Override Cylinder

2

Install Cylinder
1.

Install Cylinder if not already installed at the factory. Screws A & B (see Fig. 1) are correctly set at
factory. If it is difficult to screw in the cylinder, loosen
the two screws near the actuator (A) one turn. If you
find the cylinder is still difficult to screw in, then loosen
the other screws (B) one turn. Do not loosen the
screws all the way or it may be difficult to replace
them properly! Note: The trim is manufactured to
use a 1-1/8" or 1¼" Alarm Lock mortise cylinder with a
HW-1302 cam. If the cylinder that will be used is
longer than 1¼", a collar must be utilized. Please see
the collar information on the previous page.

Fig. 1c: Use 1/16" hex wrench to screw in
the cylinder back stop screw

NOTE: To remove cylinder, reverse steps 1a-1c.

A
B

Setting the Door "Hand"
2.

Cylinder back stop
screw

With the key always on the outside, the door hand is
generally determined by the location of the hinges-hinges are either inside or outside. See Fig. 2.

Fig. 1: Install Cylinder if not already installed at the factory
RIGHT HAND

1a. Insert key half-way into the cylinder, then screw it
in. See Fig. 1a. If cylinder will not seat flush, the cylinder back stop screw may require loosening. Cylinders
that are longer than 1¼"
will require a collar, which
will stick out from the surface when correctly installed. Please see the
cylinder information on
the previous page.
Fig. 1a: Insert key 1/2 way
into cylinder and screw in

1b. After the cylinder is screwed in all the way, center
the keyway toward the bottom (see Fig. 1b). If an
interchangeable core cylinder is utilized, then center
the interface toward the bottom. Tighten the screws
that were loosened in step 1.

LEFT HAND

RHR

REVERSE

(Keys)

LHR

(Keys)

(Hinges)

STANDARD

RH

REVERSE

LH

STANDARD

Fig. 2: Cross Section Top View -- Door Hand

2a. Setting Hand of Interface Cylinder/Adapter
Refer to Fig. 2a to determine if changing the hook
cam lever is necessary. If changing the hook cam
lever is necessary, refer to Fig. 2b (on next page).

LH/LHR

RH/RHR

Fig 2a: Correct orientation for Interface cylinder
and hook cam (LH and RH)

Fig. 1b: Center keyway toward bottom

1c. Remove the key. Use a 1/16" hex wrench to screw
the cylinder back stop screw in fully. (See Fig. 1c)
The key should now only rotate counterclockwise.

3

• Remove the retaining ring with a screwdriver.
• Remove the pin, then flip over the hook cam lever.

four mounting holes.
• IMPORTANT!--Drill the holes STRAIGHT
THROUGH the door, or the through-bolts will
not fit in the lock! THIS IS ESSENTIAL! Drill
slowly and STRAIGHT through the door.
• Reposition the template as often as needed until
it is placed correctly.

Insert the Interface Cylinder
Fig 2b: Remove the retaining ring
with a small screwdriver...

...remove the pin, then flip over hook cam
lever.

• Re-install the retaining ring displayed in
Fig. 2c (arrow).

5. Loosen the set screw, then remove the outside
cylinder (if present--See Fig. 6).
Old interface
cylinder

Set screw

Fig. 2c: Re-install the retaining ring

Install the Lever
3. Install the lever with proper orientation for the lock/
door hand used. Tighten the set screw using a 1/8" hex
wrench (see Fig. 3).
IMPORTANT!
The
top of the set screw
must be at (or below)
lever surface. If not,
check to ensure the
lever is fully pushed
toward the trim.

Fig. 6: Loosen set screw before removing the
old interface cylinder (if present)

5a. Push in latch and hold latch in all the way.

Push in
latch during
interface
cylinder
installation

Interface cylinder
Fig. 3: Tighten lever set screw
with 1/8" hex wrench

3a. Install the Adams Rite® product as indicated by the
Adams Rite® door prep guidelines and instructions.
• If a new installation, the face place must NOT be
installed at this time.
• If a retrofit installation,
remove the face plate.

Fig. 6a: Push latch in and hold

5b. While holding in the latch, carefully insert the interface
cylinder assembly into the cylinder hole. The hook
must be in front of the latch retractor and pass through
the notch in the lock case (see Fig. 6b).

Prepare the Door For
"Through-Bolting"
4. Place template (WI1459) as
shown. Important: Place the
template on top of existing cylinder hole and parallel to the
door edge.

Notch

Hook

4a. Drill completely through the
door for through-bolting the

4

Fig. 4: Template (WI1459)
through-bolt holes (circled)

Fig. 6b: While holding latch in, place hook in front of
the latch retractor and through the notch

5c. The interface cylinder must be centered and positioned flush with (or slightly below) the surface of the
door (see Fig. 7).

Install Lock
6. Install the DL lock onto the door by aligning the two
posts on the front of the interface cylinder with the two
corresponding holes in the back of the DL lock. Lift the
tailpiece slightly to ensure the tailpiece enters the slot
of the interface cylinder.

Fig. 7: Position the interface cylinder

5d. With the interface cylinder HELD SECURELY in its
correct position, tighten the set screw, securing the
interface cylinder to the lock (see Fig. 7a).
Important! If the interface cylinder is not parallel to
the door after tightening the set screw, then you must
verify that the original Adams Rite® lock body was
originally installed correctly (installed square to the
door). Failure to ensure the interface cylinder is installed correctly could cause lock binding or improper
operation of the lock mechanism.

Fig. 8: Install lock onto the door

6a. Secure the DL lock to the door with four throughdoor mounting screws and two door plates. Place a
door plate on top of a pair of mounting holes and
loosely secure lock from the inside of the door. Snug
all four mounting screws before final tightening. Do not
over-tighten.

Door plate

Fig. 7a: Tighten the interface cylinder set screw

5e. Install the latch face plate.
Fig. 9: Secure lock to door -- loosely at first

6b. Cover door plates with decorative plate covers by
sliding them from top to bottom on door plates.

Fig. 7b: Install the latch face plate

Fig. 9a: Slide down to install decorative plate covers

5

Install Batteries
7. Insert key in cylinder and turn counterclockwise. This
will allow access to the battery compartment screw.
With the supplied 5/64" Allen wrench, loosen the battery cover screw only until the battery cover is able
to slide off. Remove the battery pack.
Note: Loosening the battery cover screw in excess of
what is necessary may interfere with the mechanical
operation of the key override assembly. Although the
lock will not be damaged, when the key is removed the
assembly may not function until the battery cover screw
is re-tightened.

7b. Install battery pack into the battery compartment.
Neatly push all wiring inside the compartment. Holding battery in place, slide cover back on.
See Fig. 11.

Fig. 11: Install the battery pack

7c. While turning key counterclockwise again, allowing access to the battery cover screw, tighten the
battery cover screw fully. Turn the key clockwise and
remove.
Fig. 10: Loosen battery cover screw only until the battery
cover is able to slide off

7a.

FOR NEW INSTALLATIONS: Refer to programming instructions (OI310, OI311 or OI312) for specific instructions for "First Time Startup" and
"Change Factory Master Code" before connecting
the battery.
The lock must be powered up correctly (and have
its factory Master Code changed) or erratic lock behavior can result.

Fig. 12: Turn key counterclockwise and
tighten the cover screw.

Test operation: See next page.

6

TEST LOCK OPERATION

Before testing, be sure the lock has been poweredup using the specific instructions in the OI310,
OI311 or OI312 manuals.

4. Turn key clockwise and remove key.
The lever must not retract the latch when pressed
down.

1. With key removed, ensure that the lever CAN ONLY
be pushed down (not up), and the latch should NOT
retract while pushing down the lever with the key out.

Test Step 4

Test Step 1

2. Release lever. Insert key and turn key fully counterclockwise.

5. While pressing the default access code on the lock
keypad (press "1 2 3 4 5" on the DL1200 and press
"1 2 3 4 5 6" on the DL/PDL1300), note the following:
• For each number key pressed, the red LED lights.
• When the "5" button is pressed (or the "6" button
on the DL/PDL1300):
1. The green LED flashes for approximately 5
seconds, and then
2. The latch is retracted when the lever is pushed
down

Test Step 2

3. Depress the lever and the latch should retract.

Test Step 5
Latch
retracted

6. Test the exit device mounted inside (paddle / egress
bar, etc.) and confirm it is operating correctly.
SEE PROGRAMMING INSTRUCTIONS OI310,
OI311 or OI312 FOR KEYPAD PROGRAMMING
INFORMATION.

Test Step 3

7

ALARM LOCK LIMITED WARRANTY
ALARM LOCK SYSTEMS, INC. (ALARM LOCK)
warrants its products to be free from manufacturing
defects in materials and workmanship for 24 months
following the date of manufacture. ALARM LOCK will,
within said period, at its option, repair or replace any
product failing to operate correctly without charge to
the original purchaser or user.
This warranty shall not apply to any equipment, or
any part thereof, which has been repaired by others,
improperly installed, improperly used, abused, altered,
damaged, subjected to acts of God, or on which any
serial numbers have been altered, defaced or
removed. Seller will not be responsible for any
dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR
IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. THERE IS
NO EXPRESS OR IMPLIED WARRANTY OF
MERCHANTABILITY OR A WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE.
ADDITIONALLY, THIS WARRANTY IS IN LIEU OF
ALL OTHER OBLIGATIONS OR LIABILITIES ON
THE PART OF ALARM LOCK.
Any action for breach of warranty, including but not
limited to any implied warranty of merchantability, must
be brought within the six months following the end of
the warranty period. IN NO CASE SHALL ALARM
LOCK BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY THE SELLER'S
OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional
who installed and maintains your security system. In
order to exercise the warranty, the product must be
returned by the security professional, shipping costs
prepaid and insured to ALARM LOCK. After repair or
replacement, ALARM LOCK assumes the cost of
returning products under warranty. ALARM LOCK
shall have no obligation under this warranty, or
otherwise, if the product has been repaired by others,
improperly installed, improperly used, abused, altered,
damaged, subjected to accident, nuisance, flood, fire
or acts of God, or on which any serial numbers have
been altered, defaced or removed. ALARM LOCK will
not be responsible for any dismantling, reassembly or
reinstallation charges.
This warranty contains the entire warranty. It is the
sole warranty and any prior agreements or
representations, whether oral or written, are either
merged herein or are expressly cancelled. ALARM
LOCK neither assumes, nor authorizes any other

8

person purporting to act on its behalf to modify, to
change, or to assume for it, any other warranty or
liability concerning its products.
In no event shall ALARM LOCK be liable for an
amount in excess of ALARM LOCK's original selling
price of the product, for any loss or damage, whether
direct, indirect, incidental, consequential, or otherwise
arising out of any failure of the product. Seller's
warranty, as hereinabove set forth, shall not be
enlarged, diminished or affected by and no obligation
or liability shall arise or grow out of Seller's rendering
of technical advice or service in connection with
Buyer's order of the goods furnished hereunder.
ALARM LOCK RECOMMENDS THAT THE ENTIRE
SYSTEM BE COMPLETELY TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but
not limited to, any or all of the following; criminal
tampering, electrical or communications disruption, it is
possible for the system to fail to perform as expected.
ALARM LOCK does not represent that the product/
system may not be compromised or circumvented; or
that the product or system will prevent any personal
injury or property loss by burglary, robbery, fire or
otherwise; nor that the product or system will in all
cases provide adequate warning or protection. A
properly installed and maintained alarm may only
reduce risk of burglary, robbery, fire or otherwise but it
is not insurance or a guarantee that these events will
not occur. CONSEQUENTLY, SELLER SHALL HAVE
NO LIABILITY FOR ANY PERSONAL INJURY,
PROPERTY DAMAGE, OR OTHER LOSS BASED
ON A CLAIM THE PRODUCT FAILED TO GIVE
WARNING. Therefore, the installer should in turn
advise the consumer to take any and all precautions
for his or her safety including, but not limited to, fleeing
the premises and calling police or fire department, in
order to mitigate the possibilities of harm and/or
damage.
ALARM LOCK is not an insurer of either the property
or safety of the user's family or employees, and limits
its liability for any loss or damage including incidental
or consequential damages to ALARM LOCK's original
selling price of the product regardless of the cause of
such loss or damage.
Some states do not allow limitations on how long an
implied warranty lasts or do not allow the exclusion or
limitation of incidental or consequential damages, or
differentiate in their treatment of limitations of liability
for ordinary or gross negligence, so the above
limitations or exclusions may not apply to you. This
Warranty gives you specific legal rights and you may
also have other rights which vary from state to state.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Author                          : dblock
Create Date                     : 2006:10:23 15:39:19Z
Modify Date                     : 2016:11:11 12:58:33-05:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Metadata Date                   : 2016:11:11 12:58:33-05:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Creator                         : dblock
Title                           : xNarrow_DL1200-DL1300-PDL1300_WI1458D.22_INST.pub
Document ID                     : uuid:878f7c23-e385-421f-8f67-8080e782c359
Instance ID                     : uuid:ac891c25-566e-4b13-8b6b-1265008dc4d7
Page Count                      : 8

EXIF Metadata provided by EXIF.tools