LogicMark CS40917 CaretakerSentry Alert Watch User Manual

LogicMark, LLC CaretakerSentry Alert Watch

User Manual

Manufacturer’s Disclaimers and Limited WarrantyCOMMUNICATION AND RESPONSE LIMITATIONS: Purchaser acknowledges that signals which are transmitted over telephone lines, or other modes of communication pass through communication networks wholly beyond the control of the Manufacturer and are not maintained by the Manufacturer, and, therefore, the Manufacturer shall not be responsible for any equipment or communication failure which prevents transmission signals from reaching your contact list including emergency 911 operators or damages arising therefrom. Purchaser acknowledges that the Manufacturer provides no response to the System’s equipment. The equipment is designed to communicate with the a central station of your choice and the Manufacturer is not and shall not be responsible for ambulance, police or other emergency response time or that any response will be provided by the central monitoring station.TESTING AND SERVICE OF THIS EQUIPMENT: The equipment, once installed, are in the exclusive possession and control of the Purchaser, and it is Purchaser’s sole responsibility to test the operation of equipment and request warranty service if the equipment is under warranty.PURCHASER’S EXCLUSIVE REMEDY: Purchaser’s exclusive remedy for the Manufacturer’s default hereunder is to require the Manufacturer to repair or replace, at the Manufacturer’s option, any equipment or part of the personal emergency alert system which is non-operational during the Manufacturer’s warranty period.LIMITATION OF LIABILITY: This equipment is not designed or guaranteed to prevent any loss or injury. This Limited Warranty and Disclaimer of Liability constitutes the terms of sale and use of the equipment, and if there should arise any liability on the part of the Manufacturer as a result of any cause whatsoever, regardless of whether or not such loss, damage, or personal injury was caused by or contributed to by the Manufacturer’s negligence to any degree or failure to perform any obligation or strict products liability, such liability will be limited to an amount paid by the Purchaser to the Manufacturer for the product, or to the sum of $350.00, whichever is greater.For warranty information, see your dealer for details.BLACK Emergency Button2 Second PushAlert Watch in Pendant Bezelv7.4Base Unit - Model 40914 FCC ID: TYD-CS40914 IC: 8471A-CS40914 Watch Pendant - Model 40917FCC ID: TYD-CS40917 IC: 8471A-CS40917REN 3.7Alert Watch in Watch BezelTelephone JacksLine IN To House Phone Programming SwitchProgramming Mode “Emergency Call Mode”Normal OperationReset(Black)Power DC 7.5 800 mAhCode Learn(Red)Base Back ViewBase Top ViewRed Emergency button (Blue)(Green)(Red)Blue CareTaker buttonMicrophone(Yellow)SpeakerCancel (1 second)System Check (8 seconds)Cellular Accessory JackBase Side ViewCaretakerSentryPart #40914Features and DetailsAlert WatchPart #40917Features and DetailsAlert Watch Instructions for Adding an Alert Watch to Your CaretakerSentry
As with any timepiece, we recommend that both the batteries and bezels be replaced by a watch repair professional.Confirm Accessories in Kit1Alert Watch in Bezel with Standard 18mm watchbandLanyard and Pendant BezelTest the Unit3On the Base Unit a. PUSH and RELEASE the RED Code Learn button on back of base unit. You will hear a voice prompt, “Pendant Learning.”On the Pendanta. PUSH the BLACK Emergency button until you hear, “Pendant Learning” from the base. Then, release the button on the pendant. i. If you hear, “Base and Pendant out of Range,” STOP - wait 30 seconds and begin step 2 again.b. When pendant learning has been successful, you will hear, “Pendant Code Learned,” and then it will announce the call setting that the base is set to Programming Mode or Emergency Call Mode.Teach the Pendant to the System2*NOTES:Erasing all previously learned pendants – hold down the (Red) Code Learn button for 8 seconds. You will hear the confirmation of “Erasing All Pendants, All Pendants Erased” from the base unit. Now you can re-teach pendants starting at Step #2.Lost Pendants – If a pendant has been lost, follow the note for “Erasing all previously learned pendants” and then re-teach all of the pendants starting at Step #2.Teaching additional pendants - does not erase previously learned pendants.Exiting Learning Mode - Base will automatically exit the pendant learning mode after successfully learning the pendant or after the base announces “Pendant Learning Failed”.Up to 9 Watch pendants can be taught to each base.Place call to Emergency Operator:a. Push the BLACK EMERGENCY button for 2 seconds on the Watch Pendant. (The RED LED under the “12” should turn ON for 1 second.)b. You should hear a dial tone, dialing, and then communication tones between the CaretakerSentry and central station. Several seconds later the operator should answer the call.c. Talk normally to the base unit – just like into a speaker phone.d. At the end of the conversation, the CaretakerSentry should automatically hang-up – if not, push the CANCEL button for 1 second.Performing a System Test a. PUSH and HOLD the CANCEL button for 8-10 seconds to enter “System Check”b. Push the BLACK EMERGENCY button for 2 seconds on Pendant. (The RED LED on the pendant under the “12” should turn ON for 1 second.)c. Listen for the voice prompt from base unit:i. “All Systems are OK – Battery is OK” is heard if the system is correctly installed.ii. If any other voice prompt is heard, the unit will describe the problem.d. Push and release the CANCEL button for 1 second to exit Test Mode. (The unit will automatically exit in 3 minutes.)e. We recommend that you perform this System Test weekly.Red Code Learn buttonBLACK Emergency buttonStep-by-Step Installation GuideThe Alert Watch uses batteries CR2032 for the transmitter and SR626SW for the timepiece. Batteries and Bezels4The Alert Watch can worn both as a wristwatch and as a pendant. Simply grip the edge of the bezel and watchband and GENTLY press down on the timepiece. Then simply align the crown with the slot on the pendant bezel and snap it into place. Grip GripPressPressAlign crown and snap into placeNOTE: This watch uses a standard size 18mm band for easy replacement and personalization Breakaway Feature
Step-by-Step Installation GuideFCC Part 15.19 Warning Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATIONIS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAYNOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUSTACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THATMAY CAUSE UNDESIRED OPERATION.FCC Part 15.21 Warning StatementNOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.FCC Part 15.105 Warning StatementNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.RF warning statement:The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Navigation menu