Lsi Megaraid Enterprise 1600 Users Manual 1600.

2015-02-09

• Logical Drive Configuration
• Disclaimer
• 1 Overview
  • Single Ended and Differential SCSI Buses
  • Maximum Cable Length for SCSI Standards
  • Documentation Set
• 2 Introduction to RAID
  • RAID Overview
    • RAID Levels
    • Consistency Check
    • Fault Tolerance
    • Disk Striping
    • Disk Mirroring
    • Disk Spanning
    • Parity
    • Hot Spares
    • Disk Rebuild
    • Logical Drive
    • Hot Swap
    • SCSI Drive States
    • Logical Drive States
    • Disk Array Types
    • Enclosure Management
• 3 RAID Levels
  • Selecting a RAID Level
  • RAID 0
  • RAID 1
  • RAID 3
  • RAID 5
  • RAID 10
  • RAID 30
  • RAID 50
• 4 Features
  • SMART Technology
  • Configuration on Disk
  • Hardware Requirements
  • Configuration Features
  • Hardware Architecture Features
  • Array Performance Features
  • RAID Management Features
  • Fault Tolerance Features
  • Software Utilities
  • Operating System Software Drivers
  • MegaRAID Specifications
  • Components
  • Summary
• 5 Configuring MegaRAID
  • Configuring SCSI Physical Drives
  • Current Configuration
  • Logical Drive Configuration
  • Physical Device Layout
  • Configuring Arrays
  • Configuration Strategies
  • Assigning RAID Levels
  • Configuring Logical Drives
  • Optimizing Data Storage
  • Planning the Array Configuration
  • Array Configuration Planner
• 6 Hardware Installation
  • • Checklist
    • Installation Steps
      • Step 1 Unpack
      • Step 2 Power Down
      • Step 3 Configure Motherboard
      • Step 4 Install Cache Memory
      • Step 5 Set Jumpers
      • Step 6 Set Termination
        • SCSI Termination
      • Step 7 Set SCSI Terminator Power
      • Step 8 Connect Battery Pack (Optional)
      • Step 9 Install MegaRAID Card
      • Step 10 Connect SCSI Cables
      • Step 11 Set Target IDs
        • Device Identification on MegaRAID Controllers, Continued
      • Step 12 Power Up
      • Step 13 Run MegaRAID Configuration Utility
      • Step 14 Install the Operating System Driver
    • Summary
• 7 Cluster Installation and Configuration
  • Software Requirements
  • Hardware Requirements
  • Installation and Configuration
  • Driver Installation Instructions under Microsoft Windows 2000 Advanced Server
  • Network Requirements
  • Shared Disk Requirements
  • Cluster Installation
  • Installing the Windows 2000 Operating System
  • Setting Up Networks
  • Configuring the Cluster Node Network Adapter
  • Configuring the Public Network Adapter
  • Verifying Connectivity and Name Resolution
  • Verifying Domain Membership
  • Setting Up a Cluster User Account
  • Setting Up Shared Disks
  • Configuring Shared Disks
  • Assigning Drive Letters
  • Verifying Disk Access and Functionality
  • Cluster Service Software Installation
  • Configuring Cluster Disks
  • Validating the Cluster Installation
  • Configuring the Second Node
  • Verify Installation
  • SCSI Drive Installations
  • Configuring the SCSI Devices
  • Terminating the Shared SCSI Bus
• Troubleshooting
  • BIOS Boot Error Messages
  • Other BIOS Error Messages
  • DOS ASPI Driver Error Messages
  • Other Potential Problems
• A SCSI Cables and Connectors
  • SCSI Connectors
  • 68-Pin High Density SCSI Internal Connectors
  • 68-Pin Connector Pinout for Single-Ended SCSI
  • 68-Pin Connector Pinout for Low-Voltage Differential SCSI
• B Audible Warnings
• C Cluster Configuration with a Crossover Cable
  • Solution
• Glossary
• Index