Lutron Electronics 0021 HRT-10KP User Manual RF TT KP Instr

Download:
Mirror Download [FCC.gov]
Document ID	285209
Application ID	aAiLgmntcEYk5Vdh+CkBbA==
Document Description	USERS MANUAL FOR HRT KEYPAD
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.46kB (580805 bits)
Date Submitted	2002-11-22 00:00:00
Date Available	2002-11-18 00:00:00
Creation Date	2002-11-14 12:44:43
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2002-11-14 12:44:43
Document Title	RF TT KP Instr.qxd
Document Creator	PScript5.dll Version 5.2
Document Author:	rlau

Tabletop Keypads
Installation Instructions
Please Read Before Installing
HRT5KP-A, -C 10KP-A, -C 15KP-A, -C
5RL-A, -C 10RL-A, -C 15RL-A, -C
6LKP-A, -C
6LRL-A, -C
Description
The RF Tabletop Keypads are for use with HomeWorks
Interactive systems. The keypad buttons are programmed with a personal computer using the
HomeWorks Interactive Programming Utility.
HRT-5KP
HRT-5RL
HRT-10KP
HRT-10RL
HRT-15KP
HRT-15RL
HRT-6LKP
HRT-6LRL
Up to 32 keypads, each with a unique address, can be
assigned to each HomeWorks Interactive RF Processor.
Important Notes
Battery Models (-C only):
Use only high quality alkaline batteries, two (2) size AAA,
1.5V.
Caution - Do not use rechargeable batteries.
Using improperly rated batteries could damage
the RF Tabletop Keypad.
All Models (-A and -C):
1. Use only the DC adapter provided by Lutron with
your Tabletop RF Keypad.
Caution - Using a DC adapter not rated for the
following specifications could damage the control and possibly overheat the DC adapter.
• Input: AC 120/127V, 50/60Hz
• Output: DC 9V/300mA Class 2
2. Clean control with a soft damp cloth only. Do not
use any chemical or abrasive cleaners.
3. Operate in ambient temperatures between 0°C (32°F)
and 40°C (104°F).
4. Do not paint controls.
5. RF Keypads must be located within 30 feet (9m) of
an RF Signal Repeater or an RF Processor. Multiple
repeaters may be necessary to provide adequate
coverage.
6. RF Keypads do not function until they are addressed
and programmed. See the HomeWorks Interactive
Programming Utility online help.
Battery Installation (-C Models)
DC Adapter Installation (All Models)
1. Remove battery cover.
1. Find a suitable location for the RF Tabletop
Keypad. Place the Keypad in a convenient and
accessible location. Note: RF Keypads should be
located within 30 feet of an RF Signal Repeater or
an RF Processor.
2. Apply power to the RF Tabletop Keypad.
Verify LEDs
flash when powered
Plug in power
cord and DC
adapter
2. Install batteries as shown. Use two, 1.5V AAA
Alkaline batteries only.
3. Replace battery cover.
If the LEDs do not flash when powered,
ensure that the DC adapter is installed
properly and that there is power at the
receptacle. If problem persists, call the
Lutron Technical Support Center at (800)
523-9466.
Optional Wall Mounting
RF Tabletop Keypads may be wall mounted using the
supplied wall bracket.
Attach wall bracket to wall using the
supplied screws and wall anchors.
Note: (Battery-operated models
only)
• The RF Tabletop Keypad goes to “sleep”
after a short period of inactivity.
• Press any button to “wake up” the
Keypad.
Wrap excess DC Adapter cord (if
using) around the cord holder.
Align Keypad and snap onto
wall bracket.
HomeWorks InteractiveTM Keypad Troubleshooting
Keypad is working properly when LEDs light up and loads respond as buttons are pressed.
RF Keypads do not function until they are addressed and programmed. See the HomeWorks Interactive Programming
Utility online help.
Symptom
Cause and Action
After a Tabletop RF Keypad “wakes up”, additional button
presses cause the control to flash all its LEDs simultaneously.
• Keypad is not programmed into the system. See the RF
Processor Instructions for setup details.
A Tabletop RF Keypad’s LEDs cycle up and down during
“wake up”, but the system lights do not respond to button
presses.
• Keypad is out of system communications range. Move the
keypad to within 30 feet of an RF Repeater or RF
Processor.
• Button being pressed has not been programmed. See the
Programming Utility online help for programming details.
A battery-operated Tabletop RF Keypad will not “wake up”
when a button is pressed.
• Dead, low, or no batteries in keypad. Replace the batteries.
• Batteries are incorrectly installed. Install batteries as indicated inside the keypad.
• Batteries are not making contact with the battery terminals. Adjust the batteries so they make contact with the
terminals.
A battery-operated Tabletop RF Keypad “wakes up” but
goes to “sleep” quickly after a button press.
• Batteries are low. Replace the batteries.
Nothing happens when a Tabletop RF Keypad’s buttons
are pressed.
• No power available to keypad. Plug in power supply.
• Faulty power supply. Replace power supply.
• Keypad is not programmed. See the RF Processor
Instructions for setup details.
FCC Information
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the seperation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could
void the user’s authority to operate this equipment.
Industry Canada Information
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.
Technical and Sales Assistance
If you need assistance, call the toll-free Lutron
Technical Support Center. Please provide exact
model number when calling.
(800) 523-9466 (U.S.A., Canada and the Caribbean)
Other countries call:
Tel: (610) 282-3800
Fax: (610) 282-3090
Visit our Web site at www.lutron.com
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and printed in the U.S.A. 11/02 P/N 043-112 Rev. A
LIMITED WARRANTY
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within two years after purchase. After the two year period, a pro-rated warranty applies
to this product until eight years after the purchase. For warranty service, return unit to place
of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage prepaid. Telephone the Lutron Technical Support Center toll free at 800-523-9466. For more
information regarding this warranty contact your Lutron representative.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE
IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION,
REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE,
OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR
INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT
OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY,
OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.This product may be covered by one or more of the following U.S. patents:
5,248,919; 5,736,965; 5,838,226; 5,905,442; D389,461; D395,037; D422,969; D428,855;
D436,579 and corresponding foreign patents. U.S. and foreign patents pending. Lutron and
HomeWorks are registered trademarks and HomeWorks Interactive is a trademark of Lutron
Electronics Co., Inc.
© 2002 Lutron Electronics Co., Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:11:14 12:44:43-05:00
Modify Date                     : 2002:11:14 12:44:43-05:00
Page Count                      : 4
Creation Date                   : 2002:11:14 17:44:43Z
Mod Date                        : 2002:11:14 17:44:43Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : rlau
Metadata Date                   : 2002:11:14 17:44:43Z
Creator                         : rlau
Title                           : RF TT KP Instr.qxd

EXIF Metadata provided by EXIF.tools