Lutron Electronics 0028 Keypad User Manual RA LG Button MC

Lutron Electronics Company Inc Keypad RA LG Button MC

Users Manual

EnglishP/N 044-039Lutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299, U.S.A.Made and printed in the U.S.A. 11/03 P/N 044-039 Rev. AFCC InformationNote: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC rules. These limits aredesigned to provide reasonable protection against harmful interference in a res-idential installation. This equipment generates, uses and can radiate radio fre-quency energy and, if not installed in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guar-antee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the seperation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Caution: Changes or modifications not expressly approved by Lutron ElectronicsCo. could void the user’s authority to operate this equipment.Limited WarrantyLutron will, at its option, repair or replace any unit that is defective in materialsor manufacture within one year after purchase. For warranty service, return unitto place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA18036-1299, postage pre-paid .THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES,AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TOONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THECOST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGERESULTING FROM MISUSE, ABUSE, OR IMPROPER OR INCORRECTREPAIR, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THISWARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAM-AGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISINGOUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTAL-LATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THEPURCHASE PRICE OF THE UNIT.This warranty gives you specific legal rights, and you may also have other rightswhich vary from state to state. Some states do not allow limitations on how longan implied warranty lasts, so the above limitation may not apply to you. Somestates do not allow the exclusion or limitation of incidental or consequential dam-ages, so the above limitation or exclusion may not apply to you.These products may be covered under one or more of the following U.S.patents: 4,835,343; 4,924,349; 4,954,768; 5,248,919; 5,399,940; 5,637,930;5,736,965; 5,798,581; 5,838,226; 5,848,054; 5,905,442; 5,982,103; D422,567;D436,930; D453,742; D456,783; D461,782; D465,460; D465,770; D466,090;D466,091; D466,484; D475,024; D475,025 and corresponding foreign patents.U.S. and foreign patents pending. Lutron, Claro and RadioRA are registeredtrademarks and Chronos and Satin Colors are trademarks of Lutron ElectronicsCo., Inc.© 2003 Lutron Electronics Co., Inc.Technical AssistanceIf you have questions concerning the installation or opera-tion of this product, call the Lutron Technical SupportCenter. Please provide exact model number when calling.(800) 523-9466 (U.S.A., Canada, and the Caribbean)Other countries call (610) 282-3800Fax (610) 282-3090Visit our web site at www.lutron.comRead all instructions completely beforeinstallation.Important NotesNote: Do not use non-Lutron wallplates withthese devices.1. Install in accordance with all national and localelectrical codes.2. A neutral wire connection is required for theWall-Mounted Master control.3. Do not paint controls or wallplates.4. Clean with a soft damp cloth only.Do notuse any chemical cleaners.5. Operate in ambient temperatures between 0°C(32°F) and 40°C (104°F).6. Recommended wallbox depth is 21/2in. mini-mum.7. The range and performance of the RadioRASystem is highly dependent on a variety of com-plex factors such as:• Distance between system components• Geometry of the home• Construction of walls separating system com-ponents• Electrical equipment located near systemcomponents8. Do not mix RadioRA “A” and “B” frequencyproducts within the same system. Products withdifferent frequencies are not compatible. Installation Instructions forLarge ButtonWall-Mounted Master ControlsPlease Leave for OccupantTable of ContentsInstallationOperation of the Master ControlNote: Request Application Note #41 on how toretrofit a RadioRA Wall-Mounted MasterControl into an existing home.Large ButtonWall-Mounted Master ControlRALB-2W-SD, RALB-5W-AO, RALB-5W-RLRBLB-2W-SD, RBLB-5W-AO, RBLB-5W-RL120/127 V 50/60HzTroubleshootingSymptomA Master Control appears not tobe working.Possible Cause• No power available to unit.• Master Control is not pro-grammed into the system.Solution• Ensure power is turned on.• See Activating Controls in theRadioRA®Setup Guide.PRELIMINARYProject 602RALB- (Nov, 03) JPZ0028
InstallationInstalling a Wall-Mounted Master Control in a newly installed wallbox.Check off Steps as completed.Step 1 Turn power off at circuit breaker panel or remove fuse from fusebox.Wiring DiagramStep 3 Attach wallplate adapter. Mount and align control. Snap on Claro®or Satin ColorsTM wallplate (purchasedseparately).Step 4 Turn power ON.Align Control.Snap on wallplate.Operation of the Master ControlButtonTurns lights on/off.LEDsGlow when associatedRoom or Scene lights areon. Glow dimly as nightlight when lights are off.RaiseBrighten ROOM or SCENElights*.LowerDim ROOM or SCENElights*.* To select the ROOM or SCENE buttonyou wish to Raise or Lower, quickly tapthat button twice.Important Wiring InformationTwist wire connec-tor tight.Be sure no barewire is exposed.When making wire connections, follow the recommended strip lengths and com-binations for the supplied wire connectors. Note: Wire connectors provided aresuitable for copper wire only. For aluminum wire, consult an electrician.SmallLargeSmall:Strip insulation 3/8" for 14 AWG wireStrip insulation 1/2” for 16 or 18 AWG wireUse to join one 14 AWG supply wire with one16 or 18 AWG control wire.Large:Strip insulation 1/2" for 10, 12 or 14 AWG wireStrip insulation 5/8" for 16 or 18 AWG wireUse to join one or two 12 or 14 AWG supplywires with one 10, 12, 14, 16, or 18 AWG control wire.Step 2 Wire the Control.Using the wire connectors provided:• Connect the black control wire to theHOT wire coming from the breakerpanel.• Connect the white control wire to theNEUTRAL wire coming from the break-er panel.BlackWhiteHotNeutralTighten screwsuntil snug.NOTE: Master Controls will not operate until they have beenprogrammed.For detailed instructions on programming your MasterControl, refer to the Setup and Installation Guide for aRadioRA®ChronosTM System Bridge and Timeclock that isincluded with a Chronos or the RadioRA Setup Guide that isincluded with an RF Signal Repeater.

Navigation menu