Lutron Electronics 0028 Keypad User Manual RA LG Button MC
Lutron Electronics Company Inc Keypad RA LG Button MC
Users Manual
English
P/N 044-039
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Made and printed in the U.S.A. 11/03 P/N 044-039 Rev. A
FCC Information
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a res-
idential installation. This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the seperation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron Electronics
Co. could void the user’s authority to operate this equipment.
Limited Warranty
Lutron will, at its option, repair or replace any unit that is defective in materials
or manufacture within one year after purchase. For warranty service, return unit
to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA
18036-1299, postage pre-paid .
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO
ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE
COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE
RESULTING FROM MISUSE, ABUSE, OR IMPROPER OR INCORRECT
REPAIR, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS
WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAM-
AGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING
OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTAL-
LATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE
PURCHASE PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to you. Some
states do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitation or exclusion may not apply to you.
These products may be covered under one or more of the following U.S.
patents: 4,835,343; 4,924,349; 4,954,768; 5,248,919; 5,399,940; 5,637,930;
5,736,965; 5,798,581; 5,838,226; 5,848,054; 5,905,442; 5,982,103; D422,567;
D436,930; D453,742; D456,783; D461,782; D465,460; D465,770; D466,090;
D466,091; D466,484; D475,024; D475,025 and corresponding foreign patents.
U.S. and foreign patents pending. Lutron, Claro and RadioRA are registered
trademarks and Chronos and Satin Colors are trademarks of Lutron Electronics
Co., Inc.
© 2003 Lutron Electronics Co., Inc.
Technical Assistance
If you have questions concerning the installation or opera-
tion of this product, call the Lutron Technical Support
Center. Please provide exact model number when calling.
(800) 523-9466 (U.S.A., Canada, and the Caribbean)
Other countries call (610) 282-3800
Fax (610) 282-3090
Visit our web site at www.lutron.com
Read all instructions completely before
installation.
Important Notes
Note: Do not use non-Lutron wallplates with
these devices.
1. Install in accordance with all national and local
electrical codes.
2. A neutral wire connection is required for the
Wall-Mounted Master control.
3. Do not paint controls or wallplates.
4. Clean with a soft damp cloth only.Do not
use any chemical cleaners.
5. Operate in ambient temperatures between 0°C
(32°F) and 40°C (104°F).
6. Recommended wallbox depth is 21/2in. mini-
mum.
7. The range and performance of the RadioRA
System is highly dependent on a variety of com-
plex factors such as:
• Distance between system components
• Geometry of the home
• Construction of walls separating system com-
ponents
• Electrical equipment located near system
components
8. Do not mix RadioRA “A” and “B” frequency
products within the same system. Products with
different frequencies are not compatible.
Installation Instructions for
Large Button
Wall-Mounted Master Controls
Please Leave for Occupant
Table of Contents
Installation
Operation of the Master Control
Note: Request Application Note #41 on how to
retrofit a RadioRA Wall-Mounted Master
Control into an existing home.
Large Button
Wall-Mounted Master Control
RALB-2W-SD, RALB-5W-AO, RALB-5W-RL
RBLB-2W-SD, RBLB-5W-AO, RBLB-5W-RL
120/127 V 50/60Hz
Troubleshooting
Symptom
A Master Control appears not to
be working.
Possible Cause
• No power available to unit.
• Master Control is not pro-
grammed into the system.
Solution
• Ensure power is turned on.
• See Activating Controls in the
RadioRA®Setup Guide.
PRELIMINARY
Project 602
RALB- (Nov, 03)
JPZ0028
Installation
Installing a Wall-Mounted Master Control in a newly installed wallbox.
Check off Steps as completed.
Step 1 Turn power off at circuit breaker panel or remove
fuse from fusebox.
Wiring Diagram
Step 3 Attach wallplate adapter. Mount and align control.
Snap on Claro®or Satin ColorsTM wallplate (purchased
separately).
Step 4 Turn power ON.
Align Control.
Snap on wallplate.
Operation of the Master Control
Button
Turns lights on/off.
LEDs
Glow when associated
Room or Scene lights are
on. Glow dimly as night
light when lights are off.
Raise
Brighten ROOM or SCENE
lights*.
Lower
Dim ROOM or SCENE
lights*.
* To select the ROOM or SCENE button
you wish to Raise or Lower, quickly tap
that button twice.
Important Wiring Information
Twist wire connec-
tor tight.
Be sure no bare
wire is exposed.
When making wire connections, follow the recommended strip lengths and com-
binations for the supplied wire connectors. Note: Wire connectors provided are
suitable for copper wire only. For aluminum wire, consult an electrician.
Small
Large
Small:
Strip insulation 3/8" for 14 AWG wire
Strip insulation 1/2” for 16 or 18 AWG wire
Use to join one 14 AWG supply wire with one
16 or 18 AWG control wire.
Large:
Strip insulation 1/2" for 10, 12 or 14 AWG wire
Strip insulation 5/8" for 16 or 18 AWG wire
Use to join one or two 12 or 14 AWG supply
wires with one 10, 12, 14, 16, or 18 AWG
control wire.
Step 2 Wire the Control.
Using the wire connectors provided:
• Connect the black control wire to the
HOT wire coming from the breaker
panel.
• Connect the white control wire to the
NEUTRAL wire coming from the break-
er panel.
Black
White
Hot
Neutral
Tighten screws
until snug.
NOTE: Master Controls will not operate until they have been
programmed.
For detailed instructions on programming your Master
Control, refer to the Setup and Installation Guide for a
RadioRA®ChronosTM System Bridge and Timeclock that is
included with a Chronos or the RadioRA Setup Guide that is
included with an RF Signal Repeater.