Lutron Electronics 0040 Lighting Control Transceiver User Manual 044 004b RadioRA IR interface

Lutron Electronics Company Inc Lighting Control Transceiver 044 004b RadioRA IR interface

Users Manual

RAMC-MFE, RBMC-MFESetup and Installation Guide For a RadioRA®Multi-Function Entry Master Control®A Comprehensive Step-by-Step Guide for Installing, Programming,and Operating the Lutron RadioRA® Multi-Function Entry Master ControlNote: Please leave this manual with homeowner.Wireless Home Lighting ControlEnglish P/N 044-022
RadioRA® Setup Guide for the Entry Master Control2Notes on this ManualThe procedures to setup a RadioRA® Multi-Function Entry Master Control are contained in this manual. For moreinformation on programming the remainder of your RadioRA® System, or for advanced features, refer to theoriginal RadioRA® Setup Guide (P/N 044-001).Consumer InformationNoticeThis Visor Control System, consisting of a Multi-Function Entry Master Control and a Visor Control transmitter, must only beused to operate visible means of barrier entry such as garage doors and motorized gates. Do not use this Multi-FunctionEntry Master Control with any garage door opener that lacks the safety stop and reverse feature as required by federalsafety standards. (This includes any garage door opener model manufactured before April 1, 1982.) A garage door openerwhich cannot detect an object, signaling the door to stop and reverse, does not meet current federal safety standards. Usinga garage door opener without these features increases risk of serious injury or death.WarningThis RadioRA® system must not be used to control equipment, other than lighting, which is not visible from every master orlocal control location. It also must not be used to control equipment which could create hazardous situations such asentrapment if operated accidentally. Examples of equipment which must not be controlled by this RadioRA® system whennot visible from a Multi-Function Entry Master Control or local control location include (but are not limited to) motorizedgates, garage doors, industrial doors, and microwave ovens, heating pads, etc. It is the installer's responsibility to ensurethat the equipment, other than lighting, being controlled is visible from every master or local control location and that onlysuitable equipment is connected to this RadioRA® system.FCC InformationNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which canbe determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user's authority to operate this equipment.Important Application NoteThe Multi-Function Entry Master Control is a type of Master Control. The RadioRA® System can have a maximumof 12 Master Controls.Important Installation Notes1. Install in accordance with all national and local electrical codes.2. Do not paint the Multi-Function Entry Master Control.3. Operate in ambient temperatures between 0°C (32°F) and 40°C (104°F).4. Do not mount outside. Unit must not get wet.5. Use only the AC adapter provided by Lutron with your Multi-Function Entry Master Control. Using an ACadapter not rated at the following specifications could damage the control and possibly overheat the ACadapter.• Input: AC 120V 60Hz• Output: AC 9V/500mA Class 26. The range and performance of the RadioRA® System is highly dependent on a variety of complex factors suchas:• Distance between system components• Geometry of the home• Construction of walls separating system components• Electrical equipment located near system components
RadioRA® Setup Guide for the Entry Master Control3Table of ContentsSection 1 - OverviewOverviewMulti-Function Entry Master Control .............................................................................................4Application ExamplesActivating a “Home” Lighting Scene ............................................................................................6Controlling a Garage Door .............................................................................................................6Interfacing to a Timeclock ..............................................................................................................7Interfacing to a Security System ...................................................................................................7Section 2 - InstallationInstalling an Entry Master ControlInstallation .......................................................................................................................................8Section 3 - Start-UpActivating an Entry Master ControlActivating Control ...........................................................................................................................10Button ProgrammingAssigning a Column of Buttons as ROOMS or SCENES ............................................................11Assigning Dimmers, Switches, or GRAFIK Eye® Control Units to Buttons ...............................12Setting Light Levels/GRAFIK Eye® Scene Selection for Buttons ...............................................13Configuring General CCIs as Maintained or Momentary............................................................. 14Entry Master Control Learning a Visor Control ............................................................................ 16Section 4 - Advanced FeaturesAdvanced ProgrammingProgramming the ALL ON Button ..................................................................................................18Programming the ALL OFF Button ................................................................................................ 18Copying Button Programming .......................................................................................................18Erasing Button Programming ........................................................................................................18Programming the FULL and FLASH Buttons ...............................................................................19Deleting ALL Visor Control Transmitters from an Entry Master Control ...................................22Section 5 - TroubleshootingTroubleshooting Guide .................................................................................................................24Returning to Default Factory SettingsEntry Master Control .......................................................................................................................25
RadioRA® Setup Guide for the Entry Master Control4Section 1 - OverviewOverviewMulti-Function Entry Master ControlVisor Control Transmitter (sold separately)• Mounts to a vehicle’s visor.• Buttons provide a means for remotely activating buttonson the Entry Master Control.• Turn on an Entry Master Control SCENE• Toggles an Entry Master Control ROOM• SECURITY FULL and FLASH• To enter, press and hold Visor Control button setup assecurity button for 3 seconds.• To exit, just press any button on the Visor Control.Front ViewALL ON ButtonTurns all lights ON.CCI ButtonsProvide a means for programming thegeneral inputs. Also toggles the ROOM orSCENE when pressed.ALL OFF ButtonTurns all lights OFF.ROOM or SCENEButtons Toggle lightsON and OFF. Works justlike ROOM/SCENEbuttons on a standardRadioRA® MasterControl.FULL and FLASH ButtonsProvide a means forprogramming the securityinput. Also providediagnostic capability forFULL and FLASH.CCO ButtonsProvide a contactclosure output for aslong as the button ispressed.LEARN ButtonUsed to enter LEARNmode. LEARN mode isused when the Multi-Function Entry MasterControl is learning VisorControl Transmitterbuttons.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARN
RadioRA® Setup Guide for the Entry Master Control5Section 1 - OverviewRear ViewUse includedscrewdriver tosecure wires intoterminals.OverviewOUTPUTS INPUTS1212CCO 1 CCO 2COMCCI 2CCI 1FLASHFULLCommonCommon connection for all inputs.General InputsTurns ON a ROOM or SCENE whenset as a momentary input; toggles aROOM or SCENE when set as amaintained input.FULL FLASH Security InputActivates FULL and FLASH sceneswhile a maintained input is present.OutputsProvide a momentary contactclosure output.Terminal BlockEach terminal accepts14-22 AWG, Class 2 wire.
RadioRA® Setup Guide for the Entry Master Control6Section 1 - OverviewOverviewApplication ExamplesActivating a “Home” Lighting ScenePressing the “Home” button on the Entry Master Control activates the “Home” lighting scene.AWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETHOME AWAY GARAGE 1– OR –Pressing the “Home” buttonon the Visor Controlactivates the same “Home”lighting scene.Controlling a Garage DoorPressing the button labeled “Garage 1” closes the contact of CCO 1 to open or close the garage door.AWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETOUTPUTS INPUTS1212CCO 1 CCO 2COMCCI 2CCI 1FLASHFULLGarage Door OpenerHOME AWAY GARAGE 1– OR –Pressing the “Garage 1” button onthe Visor Control will also open orclose the garage door.
RadioRA® Setup Guide for the Entry Master Control7Section 1 - OverviewHOME SECURITY GARAGE 1OverviewInterfacing to a TimeclockThe lighting scene “Sunset” on the Entry Master Control can be activated by either pressing the button labeled“Sunset” or by an input closure on CCI 1.AWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETOUTPUTS INPUTS1212CCO 1 CCO 2COMCCI 2CCI 1FLASHFULL12:00PMOutput 1 Output 2C NO NC C NO NC– OR –Interfacing to a Security SystemAWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETOUTPUTS INPUTS1212CCO 1 CCO 2COMCCI 2CCI 1FLASHFULLOutput– OR –Enter SECURITY Mode bypressing and holding(approximately 3 seconds)the “SECURITY” button onthe Visor Control.Enter SECURITY Mode with a maintained inputclosure from a Security System.Security Panel• While in SECURITY Mode, dimmers assigned to FULL will turn on to full intensity, dimmers assigned to FLASHwill begin flashing.
RadioRA® Setup Guide for the Entry Master Control8Section 2 - InstallationOUTPUTS INPUTS1212CCO 1 CCO 2COMCCI 2CCI 1FLASHFULLInstalling an Entry Master ControlInstallationRead all instructions completely before installation.Step 1 Find a suitable location for theEntry Master ControlPlace the Entry Master Control in a convenientand accessible location. Access to input andoutput wiring should be considered whenselecting the mounting location.Note: Entry Master Control must be locatedwithin 30 feet of a Repeater. For optimum VisorControl range, the Entry Master Control shouldbe located in or near the garage.Step 2 Mount Wall BracketStep 3 Wiring to input and outputdevices.Attach wall bracket to wall using thesupplied screws and wall anchors.To GarageDoor Opener 1To GarageDoor Opener 2 From InputDevice 2From InputDevice 1From SecuritySystemNote:• Input devices can be timeclocks, motion sensors,telephone interfaces, etc.DANGER -• Do not connect line voltage power to theEntry Master Control.• Connecting line voltage power or improperwiring can result in personal injury or damageto the control or to other equipment.• All external control equipment must maintainClass 2 isolation.UPCommonExternal SwitchClosures (bycustomer)
RadioRA® Setup Guide for the Entry Master Control9Section 2 - InstallationInstalling an Entry Master ControlStep 4 Attach the AC Adapter Step 6 Plug in the AC AdapterPlug the AC Adapter into a 120VAC, 60Hz wallreceptacle.Align Entry Master Controland snap onto wallbracket.If the LEDs do not flash when powered,ensure that the AC adapter is installedproperly and that there is power at thereceptacle. If problem persists, call theLutron Technical Support Center at(800) 523-9466.Plug in powercord.?UPStep 5 Attach to Wall Bracket
RadioRA® Setup Guide for the Entry Master Control10Section 3 - Start-UpActivating an Entry Master ControlActivating ControlThe Entry Master Control is a type of Master Control. The RadioRA® System can have a maximum of 12 MasterControls.Step 1 Begin Control activationStep 2 Activate Entry Master ControlSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNStep 3 Complete Control activationFor more detailed information, refer to theRadioRA® Setup Guide (P/N 044-001)?MAINREPEATERREPEATERCONTROLSACTIVATEBEEPFLASHVERIFYAUXILIARYMAINREPEATERREPEATERCONTROLSACTIVATEBEEPFLASHVERIFYAUXILIARYPress and hold button for3 seconds.Press button.Press and hold button for3 seconds.
RadioRA® Setup Guide for the Entry Master Control11Section 3 - Start-UpAssigning a Column of Buttons as ROOMS or SCENESStep 1 Begin ROOM/SCENEassignmentSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNROOMSOnly thesebuttons areconfigurable.Step 2 Change ROOM/SCENEAssignmentStep 3 Complete ROOM/SCENEassignmentSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNFor more detailed information, refer to theRadioRA® Setup Guide (P/N 044-001)?SCENESButton ProgrammingPress and hold buttonsfor 3 seconds.Press correspondingbutton to assigncolumn as ROOM orSCENES.Press and hold buttonsfor 3 seconds.
RadioRA® Setup Guide for the Entry Master Control12Section 3 - Start-UpAssigning Dimmers, Switches, or GRAFIK Eye® ControlUnits to ButtonsStep 1 Begin assigningStep 2 Select a buttonSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNStep 3 Assign a Dimmer, Switch orGRAFIK Eye® Control UnitControl to the buttonStep 4 Select next buttonSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNStep 5 Complete assigningSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNFor more detailed information, refer to theRadioRA® Setup Guide (P/N 044-001)?Button ProgrammingPress and hold buttonsfor 3 seconds.Press button.Press tapswitch.Press button.Press and hold buttonsfor 3 seconds.
RadioRA® Setup Guide for the Entry Master Control13Section 3 - Start-UpStep 1 Begin setting light levelsSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNStep 3 Set light levels for Dimmers orGRAFIK Eye® scenesStep 2 Select a buttonSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNStep 6 Complete setting light levelsStep 5 Select the next buttonSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNFor more detailed information, refer to theRadioRA® Setup Guide (P/N 044-001)?Button ProgrammingSetting Light Levels/GRAFIK Eye® Scene Selection forButtonsPress and hold buttonsfor 3 seconds.Press button.Press raise or lower to setlevel.Press button.Press and hold buttonsfor 3 seconds.
RadioRA® Setup Guide for the Entry Master Control14Section 3 - Start-UpButton ProgrammingConfiguring General Inputs as Maintained or MomentaryNote: The Security Input is always a maintained CCI.Step 1 Begin CCI closure typeassignmentSimultaneously press and hold the FULL andALL ON buttons (approximately 3 seconds).Step 2 Changing the CCI closure typeassignmentsBoth General CCIs can be independentlyselected as a Momentary or Maintainedclosure. Press and hold a CCI button tochange it’s type.Shown: Setting CCI 2as Maintained.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNFULL and FLASH LEDs will turn ON.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNLED OFF = MomentaryLED ON = MaintainedAlways Maintained
RadioRA® Setup Guide for the Entry Master Control15Section 3 - Start-UpButton ProgrammingStep 3 Complete CCI closure typeassignmentSimultaneously press and hold the FULL andALL ON buttons (approximately 3 seconds).SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNActivateSwitchReleaseSwitchSwitchOpenMomentary Input ExampleActivateSwitchReleaseSwitchSwitchOpenA Maintained switch closure will turn an inputROOM or SCENE ON. Input ROOM orSCENE remains ON until the switch closure isreleased. When released, the input ROOM orSCENE turns OFF.Maintained Input ExampleA Momentary switch closure will turn an inputROOM or SCENE ON. A momentary switchclosure cannot turn an input ROOM orSCENE OFF.All LEDs will turn OFF.
RadioRA® Setup Guide for the Entry Master Control16Section 3 - Start-UpAWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETAWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETAWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETAWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETStep 3 Select an Entry Master ControlButtonPress and release Entry Master Control buttonthat you want to learn a Visor Control button;its LED will turn ON.LED turns ON.Entry Master Control Learning a Visor ControlStep 1 Plan which Entry MasterControl buttons you want tolearn Visor Control buttonsButton ProgrammingStep 2 Enter LEARN ModePress and hold the LEARN button on the EntryMaster Control until the green LEARN LEDturns ON (approximately 3 seconds).The green LEARN LED turns ON.AWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETHOME AWAY GARAGE 1• If the ALL ON button is selected, LEDs inthe right most column will cycle upward.• If the ALL OFF button is selected, LEDs inthe right most column will cycle downward.• If either FULL or FLASH is selected, boththe FULL and FLASH LEDs will turn ON.
RadioRA® Setup Guide for the Entry Master Control17Section 3 - Start-UpAWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETAWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETAWAYNIGHTHOMEMORNINGWELCOMEALL ON ALL OFFSECURITYFLASHFULLCCO 2CCO 1LEARNGARAGE 1GARAGE 2SUNRISESUNSETHOME AWAY GARAGE 1Button ProgrammingStep 4 Select Visor Control Button tobe learned by the Entry MasterControlPress and hold the Visor Control Button untilthe orange LED next to the selected EntryMaster Control button flashes (approximately3 seconds). The LEARN LED will also flashwhile the Visor Control button is pressed.The orange LED will turn OFF after the VisorControl button is released. The green LEARNLED will stay ON.•To verify that the Entry Master Controlbutton has learned the Visor Controlbuton, press the Visor Control buttonagain. The orange LED on the EntryMaster Control will flash.Step 6 Exit LEARN ModePress the LEARN button.The green LEARN LED turns OFF.Step 5 Repeat Steps 3 and 4 to learnadditional Visor Controlbuttons
RadioRA® Setup Guide for the Entry Master Control18Section 4 - Advanced FeaturesAdvanced ProgrammingProgramming the ALL ON ButtonTo program the ALL ON button, refer to the RadioRA® Setup Guide, Lutron P/N 044-001, section on“Programming the ALL ON Button.”Programming the ALL OFF ButtonTo program the ALL OFF button, refer to the RadioRA® Setup Guide, Lutron P/N 044-001, section on“Programming the ALL OFF Button.”Copying Button ProgrammingTo copy button programming from another Master Control button, refer to the RadioRA® Setup Guide, Lutron P/N044-001, section on “Copying Button Programming.”Erasing Button ProgrammingTo erase button programming from the Entry Master Control, refer to the RadioRA® Setup Guide, Lutron P/N 044-001, section on “Erasing Button Programming.”
RadioRA® Setup Guide for the Entry Master Control19Section 4 - Advanced FeaturesAdvanced ProgrammingProgramming the FULL and FLASH ButtonsThe Security FULL and FLASH buttons are used for programming and diagnostic purposes only.Step 1 Begin FULL and FLASHbutton programmingSimultaneously press and hold the 2nd and4th buttons in the right most column until theupper right LED begins to flash (approximately3 seconds).Upper right LED flashes.Step 2 Select the FULL ButtonPress the FULL button.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNStep 3 Assign Dimmers, Switches orGRAFIK Eye® Control Units tothe FULL button• Dimmers and Switches assigned will turn on to fullwhile in SECURITY Mode.• GRAFIK Eye® Control Units assigned will go toscene 1 while in SECURITY Mode.If you assign the wrong Dimmer,Switch or GRAFIK Eye® Control Unit tothe FULL button, turn the Dimmer,Switch or GRAFIK Eye® Control UnitOFF to unassign it.Assign a GRAFIK Eye® Control Unit to theFULL button by pressing the scene 1 button.Assign a Dimmer or Switch to the FULL buttonby turning the Dimmer or Switch ON.SwitchORDimmer•Continued on next page.FULL LED will begin to flash.LUTRON
RadioRA® Setup Guide for the Entry Master Control20Section 4 - Advanced FeaturesStep 4 Select FLASH buttonPress the FLASH button.FLASH LED will begin to flash.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNAdvanced ProgrammingStep 5 Assign Dimmers, Switches orGRAFIK Eye® Control Units tothe FLASH button• Dimmers and Switches assigned will flash ON andOFF while in SECURITY Mode.• GRAFIK Eye® Control Units assigned will alternatebetween scene 1 and OFF while in SECURITYMode.If you assign the wrong Dimmer,Switch or GRAFIK Eye® Control Unit tothe FLASH button, turn the Dimmer,Switch or GRAFIK Eye® Control UnitOFF to unassign it.Assign a Dimmer or Switch to the FLASHbutton by turning the Dimmer or Switch ON.SwitchORDimmerAssign a GRAFIK Eye® Control Unit to theFLASH button by pressing the scene 1 button.LUTRON
RadioRA® Setup Guide for the Entry Master Control21Section 4 - Advanced FeaturesStep 6 Complete FULL and FLASHbutton programmingSimultaneously press and hold the 2nd and4th buttons in the right most column until allthe LEDs begin to flutter (approximately 3seconds).SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNAdvanced Programming
RadioRA® Setup Guide for the Entry Master Control22Section 4 - Advanced FeaturesDeleting ALL Visor Control Transmitters from an EntryMaster ControlDeleting all Visor Controls from an Entry Master Control will permanently delete all Visor ControlTransmitter Buttons previously learned.Step 1 Begin deleting ALL VisorControlsStep 2 Delete ALL Visor ControlsPress and hold the CCI 1, FULL, and ALL ONbuttons in the middle column until the CCI 1and FULL LEDs begin to flash (approximately3 seconds).The CCI 1 and FULL LEDs flash.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNPress and hold the LEARN button until its LEDturns ON (approximately 3 seconds).The green LEARN LED turns ON.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNAdvanced Programming
RadioRA® Setup Guide for the Entry Master Control23Section 4 - Advanced FeaturesAdvanced ProgrammingStep 3 Complete deleting ALL VisorControlsPress the LEARN button.The green LEARN LED turns OFF.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNAll LEDs will turn OFF (except the LEARN),indicating that ALL Visor Controls have beendeleted from the Entry Master Control.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNWhile the CCI 1 and FULL LEDs areflashing, press and hold the CCI 2 andFLASH buttons in the middle column until allthe LEDs flash.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNAll LEDs (except the LEARN) flutter.
RadioRA® Setup Guide for the Entry Master Control24Section 5 - TroubleshootingTroubleshooting GuideProper operation of the RadioRA® Wireless Central Home Lighting Control System is based upon a complexseries of radio frequency (RF) communications between system components. As such, it is highly dependentupon proper system installation and programming of controls.If you experience difficulties programming or operating your RadioRA® system, please refer to this guide.Many symptoms of common system activation or programming errors are contained in this TroubleshootingGuide. If you are having a problem with your system not described here, or if you have any questions, callthe Lutron Technical Support Center at 1-800-523-9466.Symptom Possible Cause RemedyDiscontinue activating your RadioRA®system until activation of the neighboringsystem is complete.Move a system Repeater closer to theMulti-Function Entry Master Control inquestion, or you may have to add anotherRepeater.Place system in ACTIVATE CONTROLSmode.Check that breaker is on and not tripped.Verify that the plug in power supply isworking.Reprogram the Multi-Function EntryMaster Control.Verify whether the Multi-Function EntryMaster Control is in range of a Repeaterby placing the system in BEEP mode.(Refer to the Troubleshooting Section inthe RadioRA® Setup Guide P/N 044-001.)Entry Master Control must learn VisorControl Transmitter.Replace batteries in Visor ControlTransmitter with new ones (CR2032).IIIIIIIVVACTIVATE CONTROLS LED onMAIN or AUXILIARY Repeaterturns ON and then back OFFwhen attempting to go intoACTIVATE CONTROLS mode.After activating a Multi-FunctionEntry Master Control, the Multi-Function Entry Master ControlLEDs flutter for approximately 5seconds then go out.The Multi-Function Entry MasterControl appears not to beworking at all and the LEDs areOFF.The Multi-Function Entry MasterControl appears not to beworking at all and the LEDs areglowing dimly.The Visor Control Transmitter isnot communicating with theMulti-Function Entry MasterControl.Your system has encountered aneighboring system within RFcommunication range also inACTIVATE CONTROLS mode.Multi-Function Entry MasterControl is out of RF communica-tion range of nearest systemRepeater.System not in ACTIVATECONTROLS mode.No power available to the Multi-Function Entry Master Control.Faulty power supply.The Multi-Function Entry MasterControl was not programmedproperly.The Multi-Function Entry MasterControl may be out of RFcommunication range of thenearest Repeater.Entry Master Control failed tolearn Visor Control Transmitter.Batteries weak or dead.
RadioRA® Setup Guide for the Entry Master Control25Section 5 - TroubleshootingReturning to Default Factory SettingsEntry Master ControlReturning an Entry Master Control to Default Factory Settings will permanently delete all currentprogramming information. Do not do this unless you are sure that it is necessary. For more informationcall the Lutron Technical Support Center at 1-800-523-9466.Step 1 Begin returning to DefaultFactory SettingsStep 2 Complete returning to DefaultFactory SettingsEnsure that the ACTIVATE REPEATER LEDand ACTIVATE CONTROLS LED on anyRepeater is NOT ON before proceeding. Ifeither LED is ON, press the correspondingbutton until its LED turns OFF (approximately 3seconds).Press and hold the 1st, 3rd and 5th buttons inthe right most column until the correspondingLEDs begin to flash (approximately 3seconds).LEDs will flash for only 3 seconds.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNWhile the 1st, 3rd, and 5th LED areflashing, press and hold the 2nd and 4thbuttons in the right most column until all theLEDs (except the LEARN) flash(approximately 3 seconds).All LEDs will turn OFF, indicating that theMaster Control has been returned to DefaultFactory Settings.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNAll LEDs (except the LEARN) flash.SECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARNSECURITYCCI 2CCI 1FLASHFULLCCO 2CCO 1LEARN
RadioRA® Setup Guide for the Entry Master Control26Section 5 - TroubleshootingNotes
RadioRA® Setup Guide for the Entry Master Control27Section 5 - TroubleshootingNotes
RadioRA® Setup Guide for the Entry Master Control28World HeadquartersLutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299 U.S.A.TOLL FREE: (800) 523-9466 (U.S.A., Canada, andthe Caribbean)Tel: (610) 282-3800Fax: (610) 282-3090Lutron Electronics Co., Inc., reserves the right to makeimprovements or changes in its products without priornotice. Although every attempt is made to ensure thatthis information is accurate and up to date, pleasecheck with Lutron to confirm product availability, latestspecifications and suitability for your application.© 2001 Lutron Electronics Co., Inc.MADE AND PRINTED IN U.S.A.P/N 044-022 11/01 Rev. ATechnical AssistanceIf you have questions concerning the installation oroperation of this product, call the Lutron TechnicalSupport Center. Please provide exact model numberwhen calling.(800) 523-9466 (U.S.A., Canada, and the Caribbean)Other countries call (610) 282-3800Fax (610) 282-3090Visit our web site at www.lutron.comLimited WarrantyLutron will, at its option, repair or replace any unit thatis defective in materials or manufacture within oneyear after purchase. For warranty service, return unitto place of purchase or mail to Lutron Electronics Co.,Inc. at 7200 Suter Rd., Coopersburg, PA 18036-1299,postage pre-paid.THIS WARRANTY IS IN LIEU OF ALL OTHEREXPRESS WARRANTIES, AND THE IMPLIEDWARRANTY OF MERCHANTABILITY IS LIMITEDTO ONE YEAR FROM PURCHASE. THISWARRANTY DOES NOT COVER THE COST OFINSTALLATION, REMOVAL OR REINSTALLATION,OR DAMAGE RESULTING FROM MISUSE, ABUSE,OR DAMAGE FROM IMPROPER WIRING ORINSTALLATION. THIS WARRANTY DOES NOTCOVER INCIDENTAL OR CONSEQUENTIALDAMAGES. LUTRON’S LIABILITY ON ANY CLAIMFOR DAMAGES ARISING OUT OF OR INCONNECTION WITH THE MANUFACTURE, SALE,INSTALLATION, DELIVERY, OR USE OF THE UNITSHALL NEVER EXCEED THE PURCHASE PRICEOF THE UNIT.This warranty gives you specific legal rights, and youmay have other rights which vary from state to state.Some states do not allow the exclusion or limitation ofincidental or consequential damages, or limitation onhow long an implied warranty may last, so the abovelimitations may not apply to you.This product may be covered under one or more of thefollowing U.S. patents: 4,835,343; 4,954,768;5,248,919; 5,399,940; 5,637,930; 5,736,965;5,798,581; 5,838,226; 5,848,054; 5,905,442;5,982,103; DES 353,798; DES 378,814; DES 389,461;DES 389,805; DES 395,037; DES 404,013;DES 422,969; DES 428,855; DES 436,579;DES 439,220 and corresponding foreign patents. U.S.and foreign patents pending. Lutron, RadioRA, andGRAFIK Eye are registered trademarks, and FASS isa trademark of Lutron Electronics Co., Inc.© 2001 Lutron Electronics Co., Inc.

Navigation menu