Lutron Electronics 0063 Electronic Control with RF communication User Manual Stanza Keypad Install English
Lutron Electronics Company Inc Electronic Control with RF communication Stanza Keypad Install English
Contents
- 1. User Manual 1
- 2. User Manual 2
- 3. User Manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1260084 |
| Application ID | cUQe6JNCHVzdo117UrSsnQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 29.92kB (374030 bits) |
| Date Submitted | 2010-04-01 00:00:00 |
| Date Available | 2010-04-06 00:00:00 |
| Creation Date | 2008-10-14 11:23:23 |
| Producing Software | Adobe PDF Library 7.0 |
| Document Lastmod | 2010-03-19 08:14:45 |
| Document Title | Stanza Keypad Install English |
| Document Creator | Adobe InDesign CS2 (4.0.5) |
| Document Author: | S Dunn |
StanzaTM StanzaTM Keypads SZ-2B, SZ-3B, SZ-4B, SZ-5B, SZ-3/1B Installation Instructions 120 V Please Read Before Installing 50 / 60 Hz 0.5 W Installation FCC Information Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. Operation is subject to the following: (1) This device may not cause harmul interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Faceplate adapter mounting screws WARNING! Wiring with power ON may result in personal injury or death. Locate and remove fuse or lock circuit breaker in the OFF position before proceeding. SZ-2B SZ-3B SZ-5B Operation Mounting Diagram Status LEDs Indicate current scene selected; all glow softly as night lights when scene is not selected If keypad is unprogrammed, all LEDs flutter when any button is pressed Control mounting screws SZ-4B SZ-3/1B Important Notes Install in accordance with all local and national electrical codes. Environment: Ambient operating temperature: 32 to 104 °F (0 to 40 °C), 0 to 90% humidity, non-condensing. Indoor use only. Spacing: If mounting one control above another, leave at least 4.5 in (114 mm) vertical space between them. Faceplates: Use Lutron Stanza faceplates for best color match and aesthetic appearance. Do not paint controls or faceplates. Cleaning: To clean faceplate or buttons, wipe with a clean damp cloth. Do not use any chemical cleaning solutions. Wallboxes: Lutron recommends using 3.5 in (89 mm) deep wallboxes for easier installation. RF Device Placement: RF keypads must be located within 20 feet (6 m) of an RF signal repeater or a device configured as a repeater. Stanza RF keypads cannot control any device in the system until they are addressed and programmed. When powered and unaddressed, they turn on their button backlights to indicate proper operation. FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential and commercial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the seperation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. 1. T urn power OFF at fusebox or circuit breaker. 2. P repare wires. When making wire connections, follow the recommended strip lengths and combinations for the supplied wire connector. Note: Wire connectors provided are suitable for copper wire only. Wire Connector: • Strip insulation 3/8 in (9.5 mm) for 14 AWG (1.5 mm2) wire. • Strip insulation 1/2 in (12.7 mm) for 16 or 18 AWG (1.0 or 0.75 mm2) wire. 3. W ire controls as follows: a. Connect the black control wire to the Hot/Live wire coming from the distribution panel. b. Connect the white control wire to the Neutral wire coming from the distribution panel. c. Twist wire connector tight. Hot/ Live Wallbox Included: Control Wire Connectors (2) Faceplate/adapter purchased separately. Keypad Buttons Buttons are backlit for easy location in a darkened room. Mounting Screws (2) Correct: Keypad protrudes from faceplate. Returning the Keypad to Factory Settings 1. Triple-tap a button on the keypad quickly (within 1 second). 2. Press and hold the same button on the keypad for 5 seconds (until the status LEDs flash) . 3. Triple-tap the same button on the keypad quickly again. Notes • Returning to factory settings will clear all programming from the keypad, and will prevent any device from being controlled by the keypad over RF. • After being returned to factory defaults, the device will need to be re-addressed as part of a system. Incorrect: Keypad is flush with faceplate. Loosen control mounting screws. Black 120 V 50 / 60 Hz Neutral White 4. P ush all wires back into the wallbox and loosely fasten the control to the wallbox using the control mounting screws provided. Do not pinch the wires. 5. Attach Lutron Stanza faceplate adapter and faceplate. See Mounting Diagram. a. Install faceplate adapter onto front of control(s). b. Tighten control mounting screws until faceplate adapter is flush to wall (do not over-tighten). c. Snap faceplate onto faceplate adapter, and verify that control is aligned properly and keypad buttons protrude in front of the faceplate. d. If control(s) is (are) misaligned or buttons are flush with the faceplate, loosen mounting screws appropriately. 6. Restore power. Check for correct local operation (see Operation). Keypad will not control a remote device until it is addressed. Troubleshooting Guide Symptom Cause and Action Keypad LEDs do not light Power not present • Circuit breaker OFF or tripped. Perform short circuit check. Wiring error • Check wiring to be sure it matches installation instructions and wiring diagrams. Lights do not respond to a button press Improper programming • Check programming in the Stanza software. Out of RF range • Ensure device is within 20 feet (6 m) of another device configured as a repeater. All status LEDs flash when each keypad button is pressed Keypad is not addressed to the system • Address device as part of a Stanza system. Technical support: U SA, Canada, Caribbean: 1.800.523.9466 Mexico: +1.888.235.2910 Central/South America: +1.610.282.6701 Warranty: 1-year limited warranty standard. 2-year parts and labor warranty, with 8-year pro-rated parts replacement on systems that include factory startup. These products may be covered under one or more of the following U.S. patents: 5,248,919; 5,637,930; 5,838,226; 5,848,054; 5,905,442; 6,687,487; 6,803,728; and corresponding foreign patents. U.S. and foreign patents pending. Lutron and the sunburst logo are registered trademarks and Stanza is a trademark of Lutron Electronics Co., Inc. © 2008 Lutron Electronics Co., Inc. Lutron Electronics Co., Inc. Made and printed in the U.S.A. P/N 030-995 Rev. A 10/14/08
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Instance ID : uuid:2f1d02b5-9a03-44bf-a298-4597b9bd092e Document ID : adobe:docid:indd:9700f181-3320-11dd-b82a-ac4c19f22906 Rendition Class : proof:pdf Derived From Instance ID : af4e7c0a-331a-11dd-b82a-ac4c19f22906 Derived From Document ID : adobe:docid:indd:192b05e9-3237-11dd-b82a-ac4c19f22906 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00 Manifest Placed Y Resolution : 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:F01E7A69A33D11DC9AE4F26D9E047CA8, uuid:F01E7A63A33D11DC9AE4F26D9E047CA8, uuid:62BB6CB7A33D11DC9AE4F26D9E047CA8, uuid:475B50FEA33D11DC9AE4F26D9E047CA8, uuid:F762C72B286011DDB231FA88107FC6E4, uuid:6081411C76C5DA11BDC9A93607A846D6, uuid:6081411C76C5DA11BDC9A93607A846D6 Manifest Reference Document ID : uuid:F01E7A68A33D11DC9AE4F26D9E047CA8, uuid:F01E7A62A33D11DC9AE4F26D9E047CA8, uuid:62BB6CB6A33D11DC9AE4F26D9E047CA8, uuid:475B50FDA33D11DC9AE4F26D9E047CA8, uuid:CE14146E286011DDB231FA88107FC6E4, uuid:5F81411C76C5DA11BDC9A93607A846D6, uuid:5F81411C76C5DA11BDC9A93607A846D6 Create Date : 2008:10:14 11:23:23-04:00 Modify Date : 2010:03:19 08:14:45-04:00 Metadata Date : 2010:03:19 08:14:45-04:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 12364 bytes, use -b option to extract) Format : application/pdf Title : Stanza Keypad Install English Description : Stanza Keypad Install English Creator : S Dunn Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 1 Subject : Stanza Keypad Install English Author : S Dunn Keywords : Stanza, Keypad, Install, English, 2B, 3B, 4B, 5B, 3/1BEXIF Metadata provided by EXIF.tools