Lutron Electronics 0064 Visor Control Receiver User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	1184331
Application ID	jhKw8jrMra84tq3FmfBiwg==
Document Description	User Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	16.21kB (202619 bits)
Date Submitted	2009-10-16 00:00:00
Date Available	2009-10-16 00:00:00
Creation Date	2009-10-01 09:52:06
Producing Software	Adobe PDF Library 8.0
Document Lastmod	2009-10-01 10:09:14
Document Title	User Manual 1
Document Creator	Adobe InDesign CS3 (5.0.4)

English
Installation Instructions
Please Read Before Installing
Visor Control Receiver: RR-VCRX
9V
300 mA
DC Adapter: T120-9DC-3
Input: 120 V
60 Hz 6.5 W
Output: 9 V
300 mA
Typical Power Consumption*: 1.6 W
Visor Control Transmitter: LR-3B-H
3V
10 mA
Dimensions
Receiver (front view)
Features
• 2
 Contact Closure Inputs (CCI) for integration with other systems and 1 CCI for
security systems.
• 4 Contact Closure Outputs (CCO) to control up to 4 momentary garage doors or
motorized gates.
• Up to 10 Transmitters can be used with a Receiver.
• Each output can be controlled locally at the Receiver or remotely by a
Transmitter
• Includes pre-printed and blank labels for naming scenes / buttons.
Installation of a Visor Control Transmitter
1. Attach the visor clip to the Transmitter as shown in the Mounting Diagram.
2. Mount the Transmitter onto a vehicle’s visor.
*Typical Power Consumption test conditions: two LEDs on (two presets active), Receiver powered by the 9 V
supplied, no Contact Closure Outputs or Contact Closure Inputs active.
Technical Assistance:
U.S.A. / Canada: 1.800.523.9466
Mexico: +1.888.235.2910
Other Countries: +1.610.282.3800
24 hours a day, 7 days a week.
Lutron Elec­tron­ics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and printed in the U.S.A. 8/09 P/N 044-161 Rev. A
Security Input
0.23
(5.8)
Outputs
Keypad
5.25
(133.4)
Visor Transmitter
2.72
(70)
Learn
1 - Output 1
C - Common 1
2 - Output 2
C - Common 2
Security - Full
Flash
3 - Output 3
C - Common 3
4 - Output 4
C - Common 4
Input 2 - 2
Input 1 - 1
0.31
(7.9)
dia.
0.19
(4.8)
dia.
9V DC
Inputs
Full
1 2 Flash C
Symptom
Probable Cause and Action
Dimmers, keypads,
shades/drapes,
security system,
garage doors or
motorized gates do
not respond to the
Visor Control
Receiver or
Transmitter.
Power Not Present
• Ensure that the power supply cord is plugged into a
wall outlet and the power jack on the Receiver.
• Circuit Breaker is OFF or tripped. Reset or turn on
circuit breaker.
9V
Visor Control Receiver
Power
Contact Closure Outputs (CCO)
Max Voltage / Current: See Relay Contact Ratings below.
Listed Class 2 / Certified PELV
Minimum Pulse Time: 500 ms
(all inputs)
Flash
Mounting
hole
detail
Contact Closure Inputs (CCI)
at 2 mA
ON saturation: <1 V
OFF leakage: <1 µA at 9 V
Minimum Pulse Time: 40 ms
Common - C
Full
Outputs
1 C 2 C
3 C 4 C
Mounting holes
3.75
(95.3)
4.25
(108)
Transmitter (front view)
Contact Closure Terminal Blocks
Use Class 2 cable
Maximum 1,000 ft (305 m)
Each terminal holds up to one 16 AWG
(1.0 mm2) or two 18 AWG (0.75 mm2) or
smaller wire.
Power Jack (to DC adapter)
Model: T120-9DC-3
(NEC® Class 2 / IEC PELV)
Transmitter (side view)
3.19
(81)
0.75
(19)
Vertical
Voltage
Resistive Load
Inductive Load
Up to 30 V
1A
0.2 A
Contact Closure Inputs not wired correctly.
• Refer to the Connection Diagram for proper wiring.
Up to 30 V
1A
0.1 A
Up to 60 V
0.5 A
Do not use.
Contact Closure Outputs not wired correctly.
• Refer to the Connection Diagram for proper wiring.
Dead, low, or no batteries in the Transmitter.
• Install new batteries in the Transmitter (CR2032)
The Transmitter is
not communicating
with the Receiver.
Normal Operation
Horizontal
Ceiling
Visor Control Receiver
Input LEDs
Display which
CCIs are active.
Inputs
Input Buttons
Press to test CCI
programming.
Security Input
Full
Wall
#6 (M3) screw
recommended
(included)
Flash
Outputs
Keypad
Inputs
Security Input
Full
Visor Transmitter
Learn
Flash
Visor Control Receiver
Power
9V DC
Level Surface
1.06
(26.9)
Transmitter (back view)
Vehicle visor
Inputs
Full
1 2 Flash C
Outputs
1 C 2 C
3 C 4 C
Outputs
Keypad
Learn LED
Flashes to indicate
that the Receiver is
in Learn mode.
Visor Control Transmitter
The Transmitter is not programmed correctly.
the system Setup Guide to program the Transmitter.
• See

Transmitter is not within specified RF range.
• Wait until the Transmitter is within 150 ft (46 m) of the
Receiver before pressing a button on the Transmitter.
Dead, low, or no batteries in the Transmitter.
• Install new batteries in the Transmitter (CR2032).
Security Input
LEDs
Display which
Security option
has been
selected.
Security Input
Buttons
Press and hold
to test Security
programming.
Output LEDs
Display which
CCOs are active.
Output Buttons
Press to test
CCOs.
System devices are not within specified RF range.
• Ensure that dimmers, keypads and shades/drapes are
within 30 ft (9 m) of a repeater.
• Verify that all repeaters are within 60 ft (18 m) of
another repeater.
• Make sure that the Receiver is within 30 ft (9 m) of a
repeater.
• Wait until the Transmitter is within 150 ft (46 m) of the
Receiver before pressing a button on the Transmitter.
The Transmitter is not programmed correctly.
• See the system Setup Guide to program the Transmitter.
Mounting Diagram
Receiver (side view)
System devices are not programmed correctly.
• Program all devices according to the system Setup
Guide.
Receiver is not programmed correctly.
• See the system Setup Guide to program the Receiver.
Relay Contact Ratings
1.5
(38)
Installation of a Visor Control Receiver
1. Find a suitable location for the Receiver either near a security sytem panel
or above a garage door opener and within 30 ft (9 m) of a repeater. For more
information regarding the proper placement of a Receiver in a system see the
system Setup Guide located at the website listed above.
2. Mount vertically or horizontally, as shown in the Mounting Diagram, using two
#6 (M3) screws (included). When mounting, allow 7 in (177.8 mm) clearance for
the antenna and ensure convenient access to the contact closures and front
buttons. In order to achieve proper RF performance, do not mount unit in a
metal enclosure.
3. Attach the DC adapter cord to the power jack on the Receiver and insert the DC
adapter plug into a 120 V
60 Hz receptacle.
0.63
(16)
Inputs
Important Notes
 nvironment
Visor Control Receiver:
Ambient operating temperature: 32 °F to 140 °F (0 °C to 60 °C), 0% to 90%
humidity, non-condensing. Indoor use only.
Visor Control Transmitter:
Ambient operating temperature: -40 °F to 235 °F (-40 °C to 113 °C), 0% to 90%
humidity, non-condensing. Meets the Society of Automotive Engineers (SAE)
temperature standards.
	Codes
Install in accordance with all local and national electrical codes.
	Cleaning
To clean, wipe with a clean damp cloth. DO NOT use any chemical cleaning
solutions.
	Visor Control Receiver DC Adapter Power
NOTICE - Using a DC adapter not rated at the proper specifications could
damage the Receiver and possibly overheat the DC adapter. Use only the Lutron®
DC adapter listed above.
Visor Control Transmitter Battery Power
A Transmitter uses two (2) CR 2032 batteries (included). Keep batteries out
of reach of children. Using improper batteries could damage the Transmitter.
DO NOT dispose of the batteries in normal household waste. Please recycle
batteries, take to a battery disposal facility, or contact your local waste disposal
provider regarding local restrictions on the disposal or recycling of batteries.
	RF Device Placement
The Receiver must be within 30 ft (9 m) of an RF signal repeater. The typical
operating distance between a Receiver and a Transmitter is 150 ft (46 m).
	Programming
For programming instructions, see the system Setup Guide provided with the
system or visit the website listed above.
Receiver (bottom view)
6.25
(158.8)
Use these instructions to install the model numbers listed above.
For system setup instructions and tools visit:
www.lutron.com/radiora2
Troubleshooting Guide
Connection Diagram
Measurements are in inches (mm).
LEDs on the
Receiver do not
turn on when it is
powered up.
Improper AC adapter used.
• Use the DC adapter provided with the Receiver.
Top Keypad LED
on the Receiver
flashing rapidly.
Improper adapter used.
• Use the DC adapter provided with the Receiver.
Note: Refer to the system Setup Guide for additional troubleshooting
suggestions.
Remove all Visor Control Transmitters from the Visor Control Receiver
Keypad Buttons
Press to
test keypad
programing.
Visor Transmitter
Learn
Learn Button
Press and hold
for 10 seconds to
enter Learn mode.
Labels
Place pre-printed
or custom labels in
depression to name
buttons.
Keypad LEDs
Display status
of lights and
shades / drapes
programmed
to the Keypad
buttons.
adapter
Visor Control Transmitter Buttons
Press to activate functions remotely.
These products may be covered under one or more of the following U.S. patents: 5,838,226; 5,848,054; 5,905,442; 6,687,487; 6,803,728 and corresponding foreign patents. U.S. and foreign patents may be
pending. Lutron, RadioRA and the sunburst logo are registered trademarks and RadioRA 2 is a trademark of Lutron Electronics Co., Inc.
© 2009 Lutron Electronics Co., Inc.
Note: Removing the Transmitters from the Receiver will remove the capability to activate
functions on the Receiver remotely but will not remove programming from the Receiver. The
Transmitters will need to be reprogrammed to a Receiver according to the system Setup
Guide.
1. Triple tap and hold the Learn button on the Receiver. DO NOT release the button after the
third tap.
2. Keep the button pressed on the third tap until the Learn LED starts to flash slowly
(approximately 3 seconds).
3. Release the button and immediately triple tap it again. The Learn LED will flash quickly.
When the LED stops flashing, all of the Transmitters have been removed from the
Receiver.
Returning a Visor Control Receiver to Factory Settings
Note: Returning the Receiver to factory settings will erase all system programming from
the Receiver and will require the Receiver and all Transmitters to be reprogrammed into a
system according to the system Setup Guide.
1. Triple tap and hold any button (except the Learn button) on a Receiver. DO NOT release
the button after the third tap.
2. Keep the button pressed on the third tap until the LED(s) start to flash slowly
(approximately 3 seconds).
3. Release the button and immediately triple tap it again. The LEDs will flash quickly. When
the LEDs stop flashing, the Receiver has been returned to factory settings.
Warranty: For warranty information, please see the Warranty enclosed with the product, or
visit www.lutron.com/resiinfo.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Instance ID                     : uuid:fa0c504d-ea64-4574-9262-3f050e5528c8
Document ID                     : adobe:docid:indd:24ed3ede-aded-11de-ab7f-9ab6f81e12a0
Rendition Class                 : proof:pdf
Derived From Instance ID        : b77c6580-addc-11de-ab7f-9ab6f81e12a0
Derived From Document ID        : adobe:docid:indd:b77c6579-addc-11de-ab7f-9ab6f81e12a0
Manifest Link Form              : ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches
Manifest Reference Instance ID  : uuid:293040644CACDE119C1DA7BE78A4994A, uuid:DA55EB382F13DE11BC0CA12883387E6B
Manifest Reference Document ID  : uuid:DA954BFBDBA6DE118E5386E6F67080A9, uuid:D955EB382F13DE11BC0CA12883387E6B
Create Date                     : 2009:10:01 09:52:06-04:00
Modify Date                     : 2009:10:01 10:09:14-04:00
Metadata Date                   : 2009:10:01 10:09:14-04:00
Creator Tool                    : Adobe InDesign CS3 (5.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 12816 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 1
Creator                         : Adobe InDesign CS3 (5.0.4)

EXIF Metadata provided by EXIF.tools