Lutron Electronics 0071 Hybrid Keypad User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	1281780
Application ID	05hAmu9928ooMzL53i4fXQ==
Document Description	User Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	55.56kB (694536 bits)
Date Submitted	2010-05-14 00:00:00
Date Available	2010-05-14 00:00:00
Creation Date	2010-04-28 09:34:50
Producing Software	Adobe PDF Library 8.0
Document Lastmod	2010-05-04 14:08:23
Document Title	User Manual 1
Document Creator	Adobe InDesign CS3 (5.0.4)

English
Designer-style Hybrid Keypad
RRD-H6BRL
120 V
50 / 60 Hz
Typical Power Consumption*: 0.75 W
Installation Instructions
Please Read Before Installing
Use these instructions to install the model number listed above. For
system Setup Guide and tools visit: www.lutron.com/radiora2
Multigang Installations
Control
-H6BRL
50 W / VA
350 W / 450 VA
Load Specifications:
 oad Type: Hybrid Keypads are designed for use with permanently installed incandescent, magnetic
low-voltage, or tungsten halogen only. To reduce the risk of overheating and possible damage to other
equipment, do not install Hybrid Keypads to control receptacles or motor-operated appliances.
Low-Voltage Applications: Use Hybrid Keypads with magnetic (core and coil) low-voltage transformers
only. Not for use with electronic (solid-state) low-voltage transformers. Operation of a low-voltage circuit
with lamps inoperative or removed may result in transformer overheating and premature failure. Lutron
strongly recommends the following:
• Do not operate low-voltage circuits without operative lamps in place.
• Replace burned-out lamps as quickly as possible.
• Use transformers that incorporate thermal protection or fused transformer primary windings to
prevent transformer failure due to overcurrent.
Important Notes
 ARNING - Entrapment hazard - To avoid the risk of entrapment,
serious injury, or death, these controls must not be used to control
equipment which is not visible from every control location or which
could create hazardous situations such as entrapment if operated accidentally.
Examples of such equipment which must not be operated by these controls
include (but are not limited to) motorized gates, garage doors, industrial doors,
microwave ovens, heating pads, etc. It is the installer’s responsibility to ensure
that the equipment being controlled is visible from every control location and
that only suitable equipment is connected to these controls. Failure to do so
could result in serious injury or death.
Codes: Install in accordance with all local and national electrical codes.
Grounding: When no “grounding means” exist within the wallbox, then the
NEC® 2008, Article 404.9 allows a dimmer without a grounding connection to
be installed as a replacement, as long as a plastic, noncombustible wallplate is
used. For this type of installation, cap or remove the green ground wire on the
Hybrid Keypad and use an appropriate wallplate such as a Lutron® Claro® or
Satin Colors® wallplate.
Neutral Wire: Hybrid Keypads have an available neutral wire terminal that can
be connected to the neutral wire in a wallbox where the Hybrid Keypad is to
be installed. Connecting the neutral wire to a Hybrid Keypad allows a lower
minimum load to be used. Also, normal keypad operation will be available even
if the attached load is not installed or if the lamp is burned out. If a neutral
wire connection is available, connect it to the silver terminal. If a neutral wire
connection is desired but not available in the wallbox, contact a licensed
electrician for installation.
Environment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C),
0% to 90% humidity, non-condensing. Indoor use only.
Spacing: If mounting one control above another, leave at least 4 ½ in (114 mm)
vertical space between them.
Wallplates: Lutron Claro and Satin Colors wallplates are strongly recommended
for best color match and clean aesthetic appearance. Do not paint keypads,
buttons, or wallplates.
Cleaning: To clean, wipe with a clean damp cloth. Do not use any chemical
cleaning solutions.
Wallboxes: Lutron recommends using 3 ½ in (89 mm) deep wallboxes for easier
installation. Several controls may be installed in one multigang wallbox.
Remote Dimmers: Use only Remote Dimmers (RD-RD) with Hybrid Keypads.
Up to 9 RD-RD controls may be used with a Hybrid keypad.
RF Device Placement: RF dimmers, switches, keypads and shades / draperies
must be located within 30 ft (9 m) of an RF signal repeater. For systems without
an RF signal repeater, all RF dimmers, switches, keypads and shades / draperies
must be located within 30 ft (9 m) of each other. Remote dimmers and switches
are not required to be within a specific range.
Engraving: The Prepaid Engraving Certificate included with the Hybrid
Keypad can be redeemed for a custom engraved replacement kit. To order a
replacement kit please follow the instructions at: www.lutron.com/buttons
*Typical Power Consumption test conditions: load is off, all backlights on medium intensity, two LEDs on
(two presets active), keypad powered at 120 V
Technical Assistance:
U.S.A. / Canada: 1.800.523.9466
Mexico: +1.888.235.2910
Other Countries: +1.610.282.3800
24 hours a day, 7 days a week.
Lutron Elec­tron­ics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and print­ed in the U.S.A. 04/10 P/N 044-167 Rev. A
ON
15 W / VA
ON
MLV2
ON
450 W
Middle of Gang
350 W
250 W
MLV
250 W / 350 VA
200 W / 250 VA
2. C
 heck the installation for short circuits before installing control(s). With power
OFF, install standard mechanical switch(es) between Hot and load. Restore
power. If lights do not work or a breaker trips, check wiring. Correct wiring
and check again. Install control(s) only when short is no longer present.
Warranty is void if keypad is installed in a shorted circuit.
3. Wire keypads according to one of the following options:
a. Terminals:
Trim or strip wallbox wires to the length indicated by the strip gauge on the
back of the keypad.
• Push-In Terminals: Use with 14 AWG (1.5 mm2) solid copper wire
only. DO NOT use stranded or twisted wire.
Insert wires fully. To release wire, insert small, flat screwdriver into slot
below push-in terminal. Push screwdriver in while pulling wire out.
OR
• Screw Terminals: use with 12 AWG (2.5 mm2) or 14 AWG (1.5 mm2)
solid copper wire only. DO NOT use stranded or twisted wire.
Wrap wire around screw terminal. Tighten securely to 5 in-lbs (0.55 N•m).
b. Wire Connectors:
Prepare wires. When making wire connections, follow the recommended
strip lengths and combinations for the supplied wire connector.
Note: Wire connector provided is suitable for copper wire only.
Wire Connector:
• Strip insulation 3/8 in (10 mm) for 14 AWG (1.5 mm2)
Twist wire
or 12 AWG (2.5 mm2) wire
connector
• Strip insulation 7/16 in (11 mm) for 18 AWG
tight.
(0.75 mm ) wire
• Use to join one or two 14 AWG (1.5 mm2) or 12 AWG
(2.5 mm2) wires with one 18 AWG (0.75 mm2) ground wire.
For installations WITH a neutral wire: See Wiring Diagrams 1a or 1b.
For installations WITHOUT a neutral wire: See Wiring Diagram 2a or 2b.
Note: If a neutral wire connection is available, connect it to the silver terminal.
4. Push all wires back into the wallbox and loosely fasten the Hybrid Keypad to the
wallbox using the control mounting screws provided. Do not pinch the wires.
5. Attach Lutron Claro or Satin Colors wallplate adapter and wallplate. See the
Mounting Diagram.
a. Install the wallplate adapter onto the front of the Hybrid Keypad.
b. Tighten the keypad mounting screws until wallplate adapter is flush to the
wall (do not over-tighten).
c. Snap the wallplate onto the wallplate adapter and verify that the Hybrid
Keypad is aligned properly.
d. If the Hybrid Keypad is misaligned, remove wallplate and loosen the
mounting screws to adjust the Hybrid Keypad appropriately. When the Hybrid
Keypad is alligned properly, snap the wallplate onto the wallplate adapter.
6. Restore power. Check for correct local operation. See Operation.
Lamp Replacement
 ARNING - Shock hazard - For any procedure other than routine lamp
replacement, power must be disconnected at the main electrical panel.
Working with power ON could result in serious injury or even death.
For routine lamp replacement, remove power from the fixture(s) by pulling the
FASSTM switch out on both the Hybrid Keypad and all Remote Dimmers
Wiring Diagram 2a
Brass
Silver
Hot/Live
Black
120 V
50 / 60 Hz
Troubleshooting Guide
Single Location Installation without Neutral1, 2
Hybrid Keypad
Hybrid Keypad
Blue1
Blue1
Brass
Hot/Live
Green
Silver
Black
Lighting
Load
Ground
Green
120 V
50 / 60 Hz
Lighting
Load
Ground
Neutral
Neutral
Symptom
Probable Cause and Action
Lights do not
respond to a
Hybrid Keypad
button press
or do not go to
desired levels.
Power not present at keypad
• Circuit breaker tripped or OFF. Reset or turn ON
circuit breaker.
Multi-Location Installation with Neutral3, 4
Remote Dimmer
Remote Dimmer
Brass
Blue
Brass
Blue
Hot/Live
Black
120 V
50 / 60 Hz
Green
Black
Ground
Green
Hybrid Keypad
Brass
Silver
Black
Ground
Blue
Green
Lamps burned out or not installed
• Replace or install lamps.
Lighting
Load
Dioded lamps
• If dioded lamps are being used, replace with
non-dioded lamps.
Ground
Neutral
Wiring Diagram 2b
Out of RF range
• Reposition to be within 30 feet (9 m) of an RF signal
repeater.
Multi-Location Installation without Neutral2, 3
Remote Dimmer or
Hybrid Keypad
Remote Dimmer or
Hybrid Keypad
Brass
Blue
Brass
Blue
Hybrid Keypad or
Remote Dimmer
Brass
Improper programming
• Program according to the system Setup Guide.
Blue
Silver
Hot/Live
Black
120 V
50 / 60 Hz
Green
Ground
Black
Green
Black
Ground
Green
Lighting
Load
Ground
Neutral
 hen using controls in single location installations, tighten the blue terminal without any
wires attached. Do not connect the blue terminal to any other wiring or to ground.
In installations without a neutral wire connection, tighten the silver terminal without any
wires attached. Do not connect the silver terminal to any other wiring or to ground.
Up to 9 Remote Dimmers may be connected to the Hybrid Keypad. Total blue terminal
wire length may be up to 250 ft (76 m).
Neutral wire Hybrid Keypads must be connected on the load side of a multi-location
installation.
Mounting Diagram
Keypad
Mounting
Screws
Wallplate
Adapter
The FASS switch is pulled out.
•P
 ush FASS switch in.
Wiring
• Wires shorted. Make sure the blue terminal is not
grounded or shorted to any other wires.
• Wiring error. Wire the Hybrid Keypad according to
the Installation section and the appropriate Wiring
Diagram.
Wiring Diagram 1b
OFF OFF OFF
50 W
ON
Without Neutral
15 W
ON
With Neutral
Incandescent1
End of Gang
Incandescent

WARNING
- Shock hazard - To avoid the risk of electric shock, locate
and remove fuse or lock circuit breaker in the OFF position before
proceeding. Wiring with power ON could result in serious injury or death.
1. Turn power OFF at fusebox or circuit breaker.
OFF OFF
Maximum Load
ON
Minimum Load
Load Type
Single Location Installation with Neutral1
Installation
OFF
Load Type
Wiring Diagram 1a
In multigang installations, several controls are grouped horizontally in one
multigang wallbox. When combining controls in a wallbox, derating is required;
however, no derating is required for Remote Dimmers.
Derating Chart
Adapter
Mounting
Screws Wallplate
Attached lights
turn ON when top
Hybrid keypad
button is pressed,
then turn OFF
Wiring
• Wiring error. Wire the Hybrid Keypad according to
the Installation section and the appropriate Wiring
Diagram.
Load is less than minimum load requirement
• Make sure the connected load meets the
appropriate minimum load requirement for that
control. See Load Specifications.
Improper programming
• Program according to the system Setup Guide.
All LEDs on the
Hybrid Keypad
flash when any
button is pressed.
The Hybrid Keypad is in Factory Settings mode and has
not been configured to work in a system.
• Follow the steps in the system Setup Guide to program
the Hybrid Keypad.
Wallplate is warm
Solid-state control dissipation
• Solid-state Hybrid Keypads internally dissipate
about 2% of the total connected load. It is normal
for Hybrid Keypads to feel warm to the touch during
operation.
Note: Refer to the system Setup Guide for additional troubleshooting
suggestions.
Returning Hybrid Keypads to Factory Settings
Wallbox
Hybrid
Keypad
Operation
Returning a Hybrid Keypad to its Factory Settings will remove it from the
system and erase all dimmer settings and keypad programming.
Replacement
Kit
Wallplate adapter and wallplate
purchased separately.
NOTE: Orientation arrow MUST point UP.
Status LEDs
Show which
button
has been
activated.
FASS
Front
Accessible
Service
Switch
Keypad Buttons
Press to activate desired levels of lighting or
positions of shades /draperies.
By default, the internal dimmer is controlled by the
top keypad button. Tap to toggle load ON / OFF.
Raise / Lower Buttons
Lights increase / decrease in intensity and
shades / draperies raise / lower.
NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Lutron, Claro, Satin Colors, RadioRA and the sunburst logo are registered trademarks and RadioRA 2 and FASS are
trademarks of Lutron Electronics Co., Inc.
©2010 Lutron Electronics Co., Inc.
Step 1: T
 riple tap any button (except raise / lower) on the Hybrid Keypad. DO
NOT release after third tap.
Step 2: K
 eep the button pressed on the third tap until all the status LEDs start
to flash slowly (approximately 3 seconds).
Step 3: Immediately release the button and triple tap the button again. The
status LEDs on the Hybrid Keypad will flash quickly.
The Hybrid Keypad has now been returned to Factory Settings.
Warranty: For warranty information, please see the Warranty enclosed with the
product, or visit www.lutron.com/resiinfo

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
Instance ID                     : uuid:4680af57-8028-4d3c-9c20-ade30f6c5bcb
Document ID                     : adobe:docid:indd:6309774d-0455-11df-a62b-c011d64f627b
Rendition Class                 : proof:pdf
Derived From Instance ID        : 6309774b-0455-11df-a62b-c011d64f627b
Derived From Document ID        : adobe:docid:indd:b4b52d8a-5c4a-11de-92af-be6e68b29b17
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:4AA82535761DDF11B54E8F18E25D14E6, uuid:4BA82535761DDF11B54E8F18E25D14E6, uuid:47A82535761DDF11B54E8F18E25D14E6, uuid:49A82535761DDF11B54E8F18E25D14E6, uuid:9EC2CCE39407DF11AB23DB62867280FF, uuid:10217756460FDE11B8F0AED43BA2159E, uuid:0A185B40311ADE11B6228246EB4B0D61, uuid:53F04A1C0597DE11B3F6CC49E4186940, uuid:12217756460FDE11B8F0AED43BA2159E, uuid:3537D309731ADF11B029A1983431B96E, uuid:85A5E1AE3017DF11BB1ADB60A7018CEA, uuid:3437D309731ADF11B029A1983431B96E, uuid:51F04A1C0597DE11B3F6CC49E4186940, uuid:4BA82535761DDF11B54E8F18E25D14E6, uuid:4AA82535761DDF11B54E8F18E25D14E6, uuid:49A82535761DDF11B54E8F18E25D14E6, uuid:47A82535761DDF11B54E8F18E25D14E6, uuid:85A5E1AE3017DF11BB1ADB60A7018CEA, uuid:9EC2CCE39407DF11AB23DB62867280FF, uuid:10217756460FDE11B8F0AED43BA2159E, uuid:0A185B40311ADE11B6228246EB4B0D61, uuid:12217756460FDE11B8F0AED43BA2159E, uuid:51F04A1C0597DE11B3F6CC49E4186940, uuid:53F04A1C0597DE11B3F6CC49E4186940, uuid:3537D309731ADF11B029A1983431B96E, uuid:3437D309731ADF11B029A1983431B96E, uuid:4BA82535761DDF11B54E8F18E25D14E6, uuid:4AA82535761DDF11B54E8F18E25D14E6, uuid:49A82535761DDF11B54E8F18E25D14E6, uuid:47A82535761DDF11B54E8F18E25D14E6, uuid:85A5E1AE3017DF11BB1ADB60A7018CEA, uuid:9EC2CCE39407DF11AB23DB62867280FF, uuid:10217756460FDE11B8F0AED43BA2159E, uuid:0A185B40311ADE11B6228246EB4B0D61, uuid:12217756460FDE11B8F0AED43BA2159E, uuid:51F04A1C0597DE11B3F6CC49E4186940, uuid:53F04A1C0597DE11B3F6CC49E4186940, uuid:3537D309731ADF11B029A1983431B96E, uuid:3437D309731ADF11B029A1983431B96E, uuid:4BA82535761DDF11B54E8F18E25D14E6, uuid:49A82535761DDF11B54E8F18E25D14E6, uuid:47A82535761DDF11B54E8F18E25D14E6, uuid:9EC2CCE39407DF11AB23DB62867280FF, uuid:10217756460FDE11B8F0AED43BA2159E, uuid:0A185B40311ADE11B6228246EB4B0D61, uuid:12217756460FDE11B8F0AED43BA2159E, uuid:51F04A1C0597DE11B3F6CC49E4186940, uuid:53F04A1C0597DE11B3F6CC49E4186940, uuid:4AA82535761DDF11B54E8F18E25D14E6, uuid:3537D309731ADF11B029A1983431B96E, uuid:85A5E1AE3017DF11BB1ADB60A7018CEA, uuid:3437D309731ADF11B029A1983431B96E
Manifest Reference Document ID  : uuid:6F33E51F8D9CDE11952B91DEDFB4ECA8, uuid:C9EA34FB72C5DA11BDC9A93607A846D6, uuid:6D33E51F8D9CDE11952B91DEDFB4ECA8, uuid:C7EA34FB72C5DA11BDC9A93607A846D6, uuid:9DC2CCE39407DF11AB23DB62867280FF, uuid:0F217756460FDE11B8F0AED43BA2159E, uuid:09185B40311ADE11B6228246EB4B0D61, uuid:52F04A1C0597DE11B3F6CC49E4186940, uuid:11217756460FDE11B8F0AED43BA2159E, uuid:B573F8187A9CDE11952B91DEDFB4ECA8, uuid:83A5E1AE3017DF11BB1ADB60A7018CEA, uuid:BD4084052297DE11B3F6CC49E4186940, uuid:50F04A1C0597DE11B3F6CC49E4186940, uuid:C9EA34FB72C5DA11BDC9A93607A846D6, uuid:6F33E51F8D9CDE11952B91DEDFB4ECA8, uuid:C7EA34FB72C5DA11BDC9A93607A846D6, uuid:6D33E51F8D9CDE11952B91DEDFB4ECA8, uuid:83A5E1AE3017DF11BB1ADB60A7018CEA, uuid:9DC2CCE39407DF11AB23DB62867280FF, uuid:0F217756460FDE11B8F0AED43BA2159E, uuid:09185B40311ADE11B6228246EB4B0D61, uuid:11217756460FDE11B8F0AED43BA2159E, uuid:50F04A1C0597DE11B3F6CC49E4186940, uuid:52F04A1C0597DE11B3F6CC49E4186940, uuid:B573F8187A9CDE11952B91DEDFB4ECA8, uuid:BD4084052297DE11B3F6CC49E4186940, uuid:C9EA34FB72C5DA11BDC9A93607A846D6, uuid:6F33E51F8D9CDE11952B91DEDFB4ECA8, uuid:C7EA34FB72C5DA11BDC9A93607A846D6, uuid:6D33E51F8D9CDE11952B91DEDFB4ECA8, uuid:83A5E1AE3017DF11BB1ADB60A7018CEA, uuid:9DC2CCE39407DF11AB23DB62867280FF, uuid:0F217756460FDE11B8F0AED43BA2159E, uuid:09185B40311ADE11B6228246EB4B0D61, uuid:11217756460FDE11B8F0AED43BA2159E, uuid:50F04A1C0597DE11B3F6CC49E4186940, uuid:52F04A1C0597DE11B3F6CC49E4186940, uuid:B573F8187A9CDE11952B91DEDFB4ECA8, uuid:BD4084052297DE11B3F6CC49E4186940, uuid:C9EA34FB72C5DA11BDC9A93607A846D6, uuid:C7EA34FB72C5DA11BDC9A93607A846D6, uuid:6D33E51F8D9CDE11952B91DEDFB4ECA8, uuid:9DC2CCE39407DF11AB23DB62867280FF, uuid:0F217756460FDE11B8F0AED43BA2159E, uuid:09185B40311ADE11B6228246EB4B0D61, uuid:11217756460FDE11B8F0AED43BA2159E, uuid:50F04A1C0597DE11B3F6CC49E4186940, uuid:52F04A1C0597DE11B3F6CC49E4186940, uuid:6F33E51F8D9CDE11952B91DEDFB4ECA8, uuid:B573F8187A9CDE11952B91DEDFB4ECA8, uuid:83A5E1AE3017DF11BB1ADB60A7018CEA, uuid:BD4084052297DE11B3F6CC49E4186940
Create Date                     : 2010:04:28 09:34:50-04:00
Modify Date                     : 2010:05:04 14:08:23-04:00
Metadata Date                   : 2010:05:04 14:08:23-04:00
Creator Tool                    : Adobe InDesign CS3 (5.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 13198 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Has XFA                         : No
Page Count                      : 1
Creator                         : Adobe InDesign CS3 (5.0.4)

EXIF Metadata provided by EXIF.tools