Lutron Electronics 0072 Table-top Keypad User Manual 1

Lutron Electronics Company Inc Table-top Keypad 1

Contents

User Manual 1

Download: Lutron Electronics 0072 Table-top Keypad User Manual 1
Mirror Download [FCC.gov]Lutron Electronics 0072 Table-top Keypad User Manual 1
Document ID1323239
Application ID1TmTDp4Y25D/KXfUY6Xqiw==
Document DescriptionUser Manual 1
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize27.64kB (345548 bits)
Date Submitted2010-08-06 00:00:00
Date Available2010-08-06 00:00:00
Creation Date2010-05-04 14:58:57
Producing SoftwareAdobe PDF Library 8.0
Document Lastmod2010-07-09 08:28:51
Document TitleUser Manual 1
Document CreatorAdobe InDesign CS3 (5.0.4)

Sivoia® QS
Wireless
Installation Instructions
Please Read Before Installing
English
Tabletop Keypad
QSW4-T5R, QSW4-T10R,
QSW4-T15R, QSW4-T5S,
QSW4-T10S, QSW4-T15S
DC Adapter: T120-9DC-3
Input: 120 V
60 Hz 6.5 W
Output: 9 V
300 mA
Typical Power Consumption*: 0.6 W
Batteries: 2 AAA alkaline 1.5 V each
Optional Wall Mounting (continued)
Installation
Find a suitable location for the Tabletop Keypad. Place
the keypad in a convenient and accessible location within
30 ft (9 m) of an RF signal repeater.
2. W
 rap excess power supply cord (if using DC adapter)
around the cord holder. Align keypad mounting slots and
snap onto the wall bracket.
Battery Installation
1. Remove the battery cover.
Mounting slots
QSW4-T5R
QSW4-T10R
QSW4-T15R
Open
Open
Open
Open
Open
Open
Preset 1
Preset 1
Preset 1
Preset 1
Preset 1
Preset 1
Preset 2
Preset 2
Preset 2
Preset 2
Preset 2
Preset 2
Preset 3
Preset 3
Preset 3
Preset 3
Preset 3
Preset 3
Close
Close
Close
Close
Close
Close
QSW4-T5S
QSW4-T10S
QSW4-T15S
Use these instructions to install the model numbers listed above. For
system setup instructions and tools visit: www.lutron.com/radiora2
To program the system refer to the system Setup Guide.
Important Notes
Troubleshooting Guide
Symptom
Probable Cause and Action
The LEDs on
an DC adapter
powered keypad
do not turn on.
Power not present at the keypad.
• Verify that the DC adapter is plugged in.
A battery
powered keypad
does not turn on
when a button is
pressed or turns
off immediately
after the button
is pressed.
Batteries are installed incorrectly.
• Install batteries as indicated in Battery Installation.
Dimmer, switch
or shade/
drapery not
controlled by
Tabletop keypad.
The dimmer, switch or shade/drapery is not assigned to a keypad.
• Refer to the system Setup Guide to assign devices to a keypad.
Codes: Install in accordance with all local and national electrical codes.
Battery Power: Use only high quality AAA alkaline batteries. Battery powered
Tabletop Keypads will shut off after a short period of inactivity in order to conserve
battery power. Press any button on the Tabletop Keypad to turn it on.
3. Replace battery cover.
NOTICE: Do not use rechargeable batteries. Using improperly rated batteries
could damage the keypad.
WARNING: Risk of fire, explosion and burns. May result in serious injury
or death. DO NOT recharge, disassemble, crush, puncture, heat above
212 °F (100 °C) or incinerate the battery. Do not dispose of batteries
in normal household waste. Please recycle batteries, take to a battery
disposal facility, or contact your local waste disposal provider regarding
local restrictions on the disposal or recycling of batteries.
DC Adapter Power: Use only the DC adapter supplied with the keypad.
NOTICE: Using a DC adapter not rated for the proper specifications could
damage the keypad and possibly overheat the DC adapter. Refer to the ratings
shown at the top of page.
Environment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C),
0 to 90% humidity, non-condensing. Indoor use only.
Cleaning: To clean, wipe with a clean damp cloth. Do not use any chemical
cleaning solutions.
RF Device Placement: RF dimmers, switches, keypads and shades/drapes
must be located within 30 ft (9 m) of an RF signal repeater. Remote dimmers and
switches are not required to be within a specific range.
DC Adapter Installation
1. Plug the power cord into the Tabletop Keypad and the
DC adapter into an outlet.
Note: The DC Adapter does NOT charge batteries.
Rechargable batteries should NOT be used with Tabletop
Keypads.
LEDs will flash for 3
seconds when powered
Plug in
power
cord and
adapter
Note: To avoid operation issues, Lutron recommends that the keypad, DC adapter
and wall bracket should not be painted.
* Typical Power Consumption test conditions: all backlights on medium intensity,
nightlight mode enabled , six LEDs on (two presets active per column), keypad
powered by the 9 V
adapter supplied.
Optional Wall Mounting
1. A
 ttach the wall bracket to the wall using the screws and
wall anchors provided with the keypad.
Lutron Elec­tron­ics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and print­ed in the U.S.A. 05/10 P/N 045-214 Rev. B
Faulty DC adapter.
• Replace the DC adapter.
Batteries are not making contact with the battery terminals.
• Adjust the batteries so that they make contact with the battery
terminals.
Dead, low, or no batteries in the keypad.
• Install new batteries.
Devices are out of range.
• Ensure all keypads, dimmers, switches and shades/drapes are
within 30 ft (9 m) of an RF signal repeater.
The lamp(s) is(are) burned out.
• Replace lamp(s).
Either there is no power to the device or the FASS™ switch is
pulled out.
• Ensure that all devices are powered and all FASS switches
are pushed in.
Dimmer, switch
or shade/
drapery does
not go to desired
level or position
when a scene is
selected.
The system is not programmed correctly.
• Refer to the system Setup Guide to program the system
correctly.
All LEDs on the
keypad flash
when any button
on the keypad is
pressed.
The keypad has been returned to factory settings.
• Refer to the system Setup Guide.
• The keypad must be reprogrammed.
Devices are out of range.
•Ensure all keypads, dimmers, switches and shades/draperies
are within 30 ft (9 m) of an RF signal repeater.
Note: Refer to the system Setup Guide for additional troubleshooting suggestions.
Returning Keypads to Factory Settings
Returning a keypad to its Factory Settings will remove the
keypad from the system and erase all programming.
Step 1: T
 riple tap and hold any button (except the raise/
lower buttons) on a keypad. DO NOT release
the button after the third tap.
Technical Assistance:
U.S.A. / Canada: 1.800.523.9466
Mexico: +1.888.235.2910
Other Countries: +1.610.282.3800
24 hours a day, 7 days a week.
Lutron, Sivoia, and the sunburst logo are registered trademarks of Lutron Electronics Co., Inc.
©2010 Lutron Electronics Co., Inc.
Step 2: K
 eep the button pressed on the third tap until all
the LEDs start to flash slowly (approximately 3
seconds).
Step 3: Immediately release the button and triple tap it
again. The status LEDs will flash quickly. When the
LEDs stop flashing, the device has been returned to
factory settings.
FCC Information
Setup
2. Install batteries as shown. Use two (2), 1.5 V AAA
alkaline batteries only.
Returning Keypads to Factory Settings
(continued)
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio and television reception, which can be
determined by turning the equipment off and on. The user is encouraged to try to correct the
interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Note:
Changes or modifications not expressly approved by Lutron Electronics Co. could void the
user’s authority to operate this equipment.
* This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
One Year Limited Warranty
For a period of one year from the date of purchase, and subject to
the exclusions and restrictions described below, Lutron warrants
each new unit to be free from manufacturing defects. Lutron will,
at its option, either repair the defective unit or issue a credit equal
to the purchase price of the defective unit to the Customer against
the purchase price of comparable replacement part purchased
from Lutron.
Replacements for the unit provided by Lutron or, at its sole
discretion, an approved vendor may be new, used, repaired,
reconditioned, and/or made by a different manufacturer.
If the unit is commissioned by Lutron or a Lutron approved third
party as part of a Lutron commissioned lighting control system, the
term of this warranty will be extended, and any credits against the
cost of replacement parts will be prorated, in accordance with the
warranty issued with the commissioned system, except that the
term of the unit’s warranty term will be measured from the date of
its commissioning.
EXCLUSIONS AND RESTRICTIONS
This Warranty does not cover, and Lutron and its suppliers are not
responsible for:
1. Damage, malfunction or inoperability diagnosed by Lutron or a
Lutron approved third party as caused by normal wear and tear,
abuse, misuse, incorrect installation, neglect, accident, interference
or environmental factors, such as (a) use of incorrect line voltages,
fuses or circuit breakers; (b) failure to install, maintain and operate
the unit pursuant to the operating instructions provided by Lutron
and the applicable provisions of the National Electrical Code and
of the Safety Standards of Underwriter’s Laboratories; (c) use of
incompatible devices or accessories; (d) improper or insufficient
ventilation; (e) unauthorized repairs or adjustments; (f) vandalism;
or (g) an act of God, such as fire, lightning, flooding, tornado,
earthquake, hurricane or other problems beyond Lutron’s control.
2. On-site labor costs to diagnose issues with, and to remove,
repair, replace, adjust, reinstall and/or reprogram the unit or any of
its components.
3. Equipment and parts external to the unit, including those sold or
supplied by Lutron (which may be covered by a separate warranty).
4. The cost of repairing or replacing other property that is damaged
when the unit does not work properly, even if the damage was
caused by the unit.
EXCEPT AS EXPRESSLY PROVIDED IN THIS WARRANTY, THERE
ARE NO EXPRESS OR IMPLIED WARRANTIES OF ANY TYPE,
INCLUDING ANY IMPLIED WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE OR MERCHANTABILITY. LUTRON DOES
NOT WARRANT THAT THE UNIT WILL OPERATE WITHOUT
INTERRUPTION OR BE ERROR FREE. NO LUTRON AGENT,
EMPLOYEE OR REPRESENTATIVE HAS ANY AUTHORITY TO
BIND LUTRON TO ANY AFFIRMATION, REPRESENTATION
OR WARRANTY CONCERNING THE UNIT. UNLESS AN
AFFIRMATION, REPRESENTATION OR WARRANTY MADE BY
AN AGENT, EMPLOYEE OR REPRESENTATIVE IS SPECIFICALLY
INCLUDED HEREIN, OR IN STANDARD PRINTED MATERIALS
PROVIDED BY LUTRON, IT DOES NOT FORM A PART OF THE
BASIS OF ANY BARGAIN BETWEEN LUTRON AND CUSTOMER
AND WILL NOT IN ANY WAY BE ENFORCEABLE BY CUSTOMER.
IN NO EVENT WILL LUTRON OR ANY OTHER PARTY BE LIABLE
FOR EXEMPLARY, CONSEQUENTIAL, INCIDENTAL OR SPECIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR
LOSS OF PROFITS, CONFIDENTIAL OR OTHER INFORMATION,
OR PRIVACY; BUSINESS INTERRUPTION; PERSONAL INJURY;
FAILURE TO MEET ANY DUTY, INCLUDING OF GOOD FAITH
OR OF
REASONABLE CARE; NEGLIGENCE, OR ANY OTHER
PECUNIARY OR OTHER LOSS WHATSOEVER), NOR FOR ANY
REPAIR WORK UNDERTAKEN WITHOUT LUTRON’S WRITTEN
CONSENT ARISING OUT OF OR IN ANY WAY RELATED TO THE
INSTALLATION, DEINSTALLATION, USE OF OR INABILITY TO USE
THE UNIT OR OTHERWISE UNDER OR IN CONNECTION WITH
ANY PROVISION OF
THIS WARRANTY, OR ANY AGREEMENT INCORPORATING
THIS WARRANTY, EVEN IN THE EVENT OF THE FAULT, TORT
(INCLUDING NEGLIGENCE), STRICT LIABILITY, BREACH OF
CONTRACT OR BREACH OF WARRANTY OF LUTRON OR ANY
SUPPLIER, AND EVEN IF LUTRON OR ANY OTHER PARTY WAS
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
NOTWITHSTANDING ANY DAMAGES THAT CUSTOMER
MIGHT INCUR FOR ANY REASON WHATSOEVER (INCLUDING,
WITHOUT LIMITATION, ALL DIRECT DAMAGES AND ALL
DAMAGES LISTED ABOVE), THE ENTIRE LIABILITY OF LUTRON
AND OF ALL OTHER PARTIES UNDER THIS WARRANTY On ANY
CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION
WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY,
USE, REPAIR, OR REPLACEMENT OF THE UNIT, OR ANY
AGREEMENT INCORPORATING THIS WARRANTY, AND
CUSTOMER’S SOLE REMEDY FOR THE FOREGOING, WILL BE
LIMITED TO THE AMOUNT PAID TO LUTRON BY
CUSTOMER FOR THE UNIT. THE FOREGOING LIMITATIONS,
EXCLUSIONS AND DISCLAIMERS WILL APPLY TO THE
MAXIMUM EXTENT ALLOWED BY APPLICABLE LAW, EVEN IF
ANY REMEDY FAILS ITS ESSENTIAL PURPOSE.
TO MAKE A WARRANTY CLAIM
To make a warranty claim, promptly notify Lutron within the
warranty period described above by calling the Lutron Technical
Support Center at (800) 523-9466. Lutron, in its sole discretion,
will determine what action, if any, is required under this warranty.
To better enable Lutron to address a warranty claim, have the unit’s
serial and model numbers available when making the call. If Lutron,
in its sole discretion, determines that an on-site visit or other
remedial action is necessary, Lutron may send a Lutron Services
Co. representative or coordinate the dispatch of a representative
from a Lutron approved vendor to Customer’s site, and/or
coordinate a warranty service call between Customer and a Lutron
approved vendor.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. Some states do
not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you. Some states do not allow
the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
Lutron, the sunburst logo, and Sivoia are registered trademarks of
Lutron Electronics Co., Inc.
WARRANTY CLAIMS, TECHNICAL ASSISTANCE AND
WARRANTY INFORMATION
Contact the Lutron Technical Support Center at the numbers
provided below or your local Lutron sales representative with
questions concerning the installation or operation of the System
or this Warranty, or to make a warranty claim. Please provide the
exact model number when calling.
WORLD HEADQUARTERS
Lutron Electronics Co., Inc. 7200 Suter Road
Coopersburg, PA 18036 United States
Tel: +16102823800
Fax: +16102821243
CUSTOMER SERVICE/EMAIL
shadinginfo@lutron.com
TECHNICAL SUPPORT & SERVICES
USA +16102823800 – 24 hours/7 days
INTERNET: www.lutron.com
Europe Headquarters | United Kingdom
Lutron EA Ltd
6 Sovereign Close
London, E1W 3JF, UK
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
Technical Support: +44.(0)20.7480.6899
FREEPHONE: 0800.282.107
Asian Headquarters | Singapore
Lutron GL Ltd
15 Hoe Chiang Road
#07-03
Singapore, 089316
TEL: +65.6220.4666
FAX: +65.6220.4333
Technical Support: 800.120.4491
©2010 LUTRON Electronics Co., Inc.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-702
Instance ID                     : uuid:f695ee80-97dd-4851-84df-88beb3d823c1
Document ID                     : adobe:docid:indd:13fb7e40-591e-11df-9a9e-966fa18b0350
Rendition Class                 : proof:pdf
Derived From Instance ID        : 13fb7e3f-591e-11df-9a9e-966fa18b0350
Derived From Document ID        : adobe:docid:indd:13fb7e3e-591e-11df-9a9e-966fa18b0350
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:DF0F72E72018DB1184FBCD2CEFF46562, uuid:02A89A6B2318DB1184FBCD2CEFF46562, uuid:AEB36ACDA1E1DE118985D9B9110DCD28, uuid:0B9ECE81A447DF11A9D284AFFF18ACD5, uuid:B0B36ACDA1E1DE118985D9B9110DCD28, uuid:4f78fb9e-04f7-5b4d-aa54-77770cd56731, uuid:53ea61c0-ef3e-4147-8f41-23c450949f9c, uuid:3e5f3417-5e23-2449-9d4d-45432e04ec4a
Manifest Reference Document ID  : uuid:DE0F72E72018DB1184FBCD2CEFF46562, uuid:E00F72E72018DB1184FBCD2CEFF46562, uuid:ADB36ACDA1E1DE118985D9B9110DCD28, uuid:0A9ECE81A447DF11A9D284AFFF18ACD5, uuid:AFB36ACDA1E1DE118985D9B9110DCD28, uuid:EA6672C6DEC3DE11ADF0B87C18FC4CD8, uuid:EC6672C6DEC3DE11ADF0B87C18FC4CD8, uuid:CD4FBA67E1C3DE11ADF0B87C18FC4CD8
Create Date                     : 2010:05:04 14:58:57-04:00
Modify Date                     : 2010:07:09 08:28:51-04:00
Metadata Date                   : 2010:07:09 08:28:51-04:00
Creator Tool                    : Adobe InDesign CS3 (5.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 11819 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 1
Creator                         : Adobe InDesign CS3 (5.0.4)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: JPZ0072

Navigation menu