Lutron Electronics 0074 RF Theromstat User Manual

Lutron Electronics Company Inc RF Theromstat

Contents

user manual

Download: Lutron Electronics 0074 RF Theromstat User Manual
Mirror Download [FCC.gov]Lutron Electronics 0074 RF Theromstat User Manual
Document ID1407192
Application ID8axJzuZoGJWXcI7xUUWCrA==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize44.22kB (552809 bits)
Date Submitted2011-01-20 00:00:00
Date Available2011-01-20 00:00:00
Creation Date2010-12-06 08:20:36
Producing SoftwareAdobe PDF Library 8.0
Document Lastmod2010-12-06 08:20:37
Document Titleuser manual
Document CreatorAdobe InDesign CS3 (5.0)

Mounting Diagram
English
seeTemp™ Wall Display
Installation Instructions
Wallplate
Adapter
Mounting
Screws
LRD-WST-F, LRD-WST-C
24 V
or 120 V
50 / 60 Hz 0.1 A
Typical Power Consumption*: 1 W
Please Read Before Installing
Adapter
Mounting Wallplate
Screws
Environment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C),
0 to 90% humidity, non-condensing. Indoor use only.
3. Exit Add Mode: Press and hold the “Add” button on any Repeater for 3 seconds until “Add” LED
begins to rapid-flash. After LED turns off (can take up to 30–60 seconds), system has exited Add
Mode.
eco
Wallplates: Use only Lutron® wallplates with these devices. The mechanical design of the
seeTemp Wall Display is NOT compatible with non-Lutron wallplates. Non-Lutron wallplates
will NOT sit flush against the wall. Claro® and Satin Colors® wallplates are strongly
recommended for best color match and clean aesthetic appearance. Do not paint controls, buttons,
or wallplates.
Cleaning: To clean, wipe with a clean damp cloth. Do not use any chemical cleaning solutions.
4. Test the system:
Wallbox
a.	Set the seeTemp to Heat or Cool mode.
seeTemp
Wall Display
Wallplate adapter and wallplate
purchased separately.
in (89 mm) deep
Installation
Room Temperature LEDs
Column of LEDs that display
the current room temperature.
ON
ON
OFF OFF OFF
seeTemp® Wall Display
ON
RF Device Placement: RF must be located within 30 ft (9 m) of an RF signal repeater.
WARNING: Shock Hazard. To avoid the risk of electric shock, locate and
remove fuse or lock circuit breaker in the OFF position before proceeding.
Wiring with power ON could result in serious injury or death.
1.	Turn power OFF at fusebox or circuit breaker.
2.	Prepare wires. When making wire connections, follow the recommended strip lengths and combinations
for the supplied wire connectors. Note: Wire connectors provided are suitable for copper wire only.
• Strip insulation 3/8 in (10 mm) for 14 AWG (1.5 mm2 ).
• Strip insulation 1/2 in (13 mm) for 18 AWG (0.75 mm2 ).
• Use to join one 14 AWG (1.5 mm2 ) with one 18 AWG (0.75 mm2 ) wires.
3.	Wire control.
120 V
Wiring
Hot/Live
Set Temperature LEDs
Column of LEDs that display the
current set temperature point. Set LED
turns off when system is turned off.
Probable Cause and Action
LEDs on a seeTemp Wall Display don’t light
up when the buttons on it are pressed.
Power not present at seeTemp Wall Display
• Circuit breaker OFF. Turn ON breaker.
Incorrect wiring.
• Wire the seeTemp Wall Display according to the
Installation section.
Press to raise the Set temperature.
Raise/Lower Rocker
Press to lower the Set temperature.
75°
70°
65°
eco
60°
Heat
Cool
Auto
Off
Fan
On
HVAC controller not controlled by a
seeTemp Wall Display and/or temperature is
not changing.
Eco Button
Press to toggle Eco mode on/off.
Black
Green
Auto
HVAC equipment does not have enough power and can’t
reach setpoint
Ground
Flip-Down Door
Covers the System and
Fan buttons. Opens 180°.
70°
Fan Buttons
Indicates the current fan setting. Button
will light up when selected.
On – Fan is constantly on.
Auto – Fan is on only when Heat/Cool
is active.
65°
Black
Green
OFF OFF
NOTE: O
 rientation arrow
MUST point UP.
OFF
Wiring
5.	Attach Lutron Claro or Satin Colors wallplate adapter and wallplate (see Mounting Diagram).
a. Install the wallplate adapter onto the front of the seeTemp Wall Display.
b. Tighten mounting screws until wallplate adapter is flush to wall (do not over-tighten).
c. Snap wallplate onto wallplate adapter and verify that the color replacement kit is aligned properly.
d. If control(s) are misaligned, loosen mounting screws appropriately.
6.	Restore power.
ON
LUTRON
ON
White
ON
eco
60°
*
80°
*Cap ground wire for 24 V
wiring applications.
24 V
50 / 60 Hz
70°
65°
eco
60°
White
LUTRON
Programming
After installation, the HVAC controller (LR-HVAC) will only function when programmed to a system with
a seeTemp™ Wall Display (LRD-WST). For full functionality, the HVAC Controller must be programmed
to a RadioRA® 2 Main Repeater (RR-MAIN-REP) and PC software must be used by a Lutron factorytrained installer. For questions on how to become a qualified installer, please contact your local Lutron
representative.
Temporary Programming
4.	Push all wires back into the wallbox and loosely fasten the control to the wallbox using the seeTemp
Wall Display mounting screws provided. Do not pinch the wires. See Mounting Diagram below.
*Typical Power Consumption test conditions: all backlights on medium intensity, two LEDs on seeTemp Wall Display powered at 120 V
Technical Assistance | 24 hours a day, 7 days a week | www.lutron.com
U.S.A. / Canada: 1.800.523.9466 | Mexico: +1.888.235.2910 | Other Countries: +1.610.282.3800
Lutron Elec­tron­ics Co., Inc.
7200 Suter Road | Coopersburg, PA 18036-1299
Print­ed in the U.S.A. 11/2010 P/N 041-298 Rev. A
6 LEDs on the seeTemp Wall Display flash
when any button is pressed.
The seeTemp Wall Display is in the Factory Settings mode
and has not been configured to work in a system.
•F
 ollow the steps in Programming.
Room Temperature LED flashes rapidly.
Low battery on Wireless Temperature Sensor.
•R
 eplace battery in Wireless Temperature Sensor.
Set temperature LED flashes rapidly.
The seeTemp Wall Display is hearing the wired backup
sensor and cannot hear Wireless Temperature Sensor.
•M
 ove Wireless Temperature Sensor closer to a repeater.
Room LED scrolls up and down.
No Wireless Temperature Sensor or wired backup is
present.
•R
 eplace battery in Wireless Temperature Sensor.
•A
 dd a Wireless Temperature Sensor.
•A
 dd a wired backup sensor.
Room and set LED scrolls up and down
when button is pressed.
Communication Error.
•M
 ove a repeater closer to a seeTemp Wall Display.
Returning a seeTemp Wall Display to Factory Settings
Room Set
75°
The HVAC controller is not assigned to a seeTemp Wall
Display.
•F
 ollow the steps in Programming.
There is no power to the device.
•E
 nsure that the device is powered
NOTE: O
 rientation arrow
MUST point UP.
120 V
50 / 60 Hz
24 V
Common
Symptom
80°
75°
24 V
from HVAC
equipment
c.	As the temperature changes, the HVAC controller will control the HVAC equipment when required.
Temperature may take up to 20 minutes to change in
the space
Room Set
24 V
b.	Tap the link button on the Wireless Temperature Sensor. The Temperature will update on the
seeTemp.
Troubleshooting Guide for seeTemp Wall Display
Room Set
System Buttons
Indicates the current system
setting. When selected,
buttons will light up according
to the following:
Heat - Red
Cool - Blue
Auto - Orange
Off - Orange
80°
Neutral
a.	For the HVAC controller, press and hold the Link button for 3 seconds until all LEDs normal-flash
(once per second).
c.	For the Wireless Temperature Sensor, press and hold the Link button for 6 seconds until the hidden
LED flashes (once per second).
Codes: Install in accordance with all local and national electrical codes.
1⁄ 2
(continued)
b.	For the seeTemp, press and hold the Eco button for 3 seconds until all LEDs normal-flash (once
per second).
Important Notes
Wallboxes: All seeTemp Wall Display units require a U.S. wallbox. 3
recommended, 2 1⁄ 4 in (57 mm) deep minimum.
Temporary Programming
2. Add the devices to the Main Repeater:
Since the HVAC system may need to function before a Lutron factory-trained installer is available for
programming, temporary programming may be used to provide climate control.
To complete the steps below, the following are required: RadioRA 2 Main Repeater (RR-MAIN-REP)
within 30 ft of the HVAC controller, seeTemp unit(s), and Wireless Temperature sensor(s).
1. Enter Add Mode: Press and hold the “Add” button on Main Repeater for 3 seconds until green “Add”
LED begins to rapid-flash (ten times per second) and repeater beeps. Wait 10 seconds.
Returning a seeTemp Wall Display to its Factory Settings will remove the seeTemp Wall Display from the
system and erase all programming.
Step 1: T
 riple tap the ECO button on the seeTemp Wall Display. DO NOT release after third tap.
Step 2: K
 eep the button pressed on the third tap until all the status LEDs start to flash slowly (approximately
3 seconds).
Step 3: Immediately release the button and triple tap the button again. The status LEDs on the seeTemp Wall
Display will flash quickly.
The seeTemp Wall Display has now been returned to Factory Settings.
Warranty: For warranty information, please see the Warranty enclosed with the product, or visit
www.lutron.com/resiinfo
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c006 1.236519, Wed Jun 14 2006 08:31:24
Instance ID                     : uuid:48ebfde9-711c-49f6-ab36-f8b6b3e58e90
Document ID                     : adobe:docid:indd:00d6c585-cbca-11df-b307-ced790c13628
Rendition Class                 : proof:pdf
Derived From Instance ID        : 00d6c584-cbca-11df-b307-ced790c13628
Derived From Document ID        : adobe:docid:indd:178ab69d-cb2b-11df-9ccb-8052682b0a9c
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:7860F4D45062DE119979F126F7D3F84E, uuid:7860F4D45062DE119979F126F7D3F84E, uuid:FC241998C5CBDF119F29A045DABA0B38, uuid:FA81CE76A800DB11AE108EA38A6D00F8, uuid:23299C2BB9D0DF11A96DF1EF5A90DAB2, uuid:3964009A9299DF11AC13F44AC749A36A, uuid:7860F4D45062DE119979F126F7D3F84E, uuid:BFF2EDBAC1D0DF11A96DF1EF5A90DAB2, uuid:7860F4D45062DE119979F126F7D3F84E, uuid:C1F2EDBAC1D0DF11A96DF1EF5A90DAB2, uuid:7860F4D45062DE119979F126F7D3F84E
Manifest Reference Document ID  : uuid:351EBD1D4C57DE11A4E1FC9FF2836DD1, uuid:351EBD1D4C57DE11A4E1FC9FF2836DD1, uuid:FB241998C5CBDF119F29A045DABA0B38, uuid:F981CE76A800DB11AE108EA38A6D00F8, uuid:22299C2BB9D0DF11A96DF1EF5A90DAB2, uuid:3664009A9299DF11AC13F44AC749A36A, uuid:351EBD1D4C57DE11A4E1FC9FF2836DD1, uuid:1DEC1AA4CCA0DF118BDBD88A2456CD01, uuid:351EBD1D4C57DE11A4E1FC9FF2836DD1, uuid:24299C2BB9D0DF11A96DF1EF5A90DAB2, uuid:351EBD1D4C57DE11A4E1FC9FF2836DD1
Create Date                     : 2010:12:06 08:20:36-05:00
Modify Date                     : 2010:12:06 08:20:37-05:00
Metadata Date                   : 2010:12:06 08:20:37-05:00
Creator Tool                    : Adobe InDesign CS3 (5.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 11728 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 1
Creator                         : Adobe InDesign CS3 (5.0)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: JPZ0074

Navigation menu