Lutron Electronics 0085 Shade Controller User Manual

Lutron Electronics Company Inc Shade Controller

User Manual

Sivoia® QS Wireless Cellular ShadeAutomated shade with wireless (RF) controlInstallation and Programming Guide (please read before installing)EnglishInside mount3Outside mount488.18.4Start Here1. Review components2. Install mounting brackets3. Install batteries4. Install the shade in the brackets5. Removing the shade from the brackets6. Programming optionsReview componentsIncluded:1 Batteries not included Tools required:Install mounting bracketsMount the left and right brackets 2 inches infrom each end of the shade.Note: Mount additional brackets evenly between the end brackets and clear of the cord lift.2CloseOpenCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseorCloseOpen OpenPresetCloseInstall batteriesRefer to the battery holders for proper battery alignment.Install the shade in the bracketsClick the shade into place as shown below. 6 Programming RadioRA® 2• For assignment and programming without RadioRA 2 design and programming software, refer to the RadioRA 2 setup guide, available at www.lutron.com/radiora2• Otherwise, use the RadioRA 2 Essentials or Inclusive software to assign and program your cellular shades. HomeWorks® QS• Use the HomeWorks QS design and programming software to assign and program your cellular shades. Standalone• Proceed to steps 7 and 8 to assign and program your cellular shades with standalone controls.7.17.2 Assign control:CloseOpenCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseorCloseOpen OpenPresetCloseHold “Close” (6 seconds)Shade LED blinks for 2 secondsSet the limitsNote: Shade limits must either be set with a Pico® or with RadioRA2 or Homeworks QS design and programming software.8.2 Enter limit setup mode: Hold “Open” AND “Raise” (3 seconds)Shade LED blinks for 2 seconds, then remains on.8.3 Adjust limits:Press “Raise” or “Lower” Shade LED remains on solid green.Save and exit:To set the upper limit: Hold “Open” (6 seconds)To set the lower limit: Hold “Close” (6 seconds)Shade LED blinks for 2 seconds, then turns off. e e CloseOpenCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseorCloseOpen OpenPresetCloseCloseOpenCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseorCloseOpen OpenPresetCloseTap shade button - shade LED turns on solid greenTap shade button - Shade LED turns on solid green e Troubleshooting10Symptom SolutionShade does not go all the way downFabric needs to relax (close shade for 24 hours then reset the lower limit)Reset the lower limitShade hangs unevenlyEnsure that fabric is not pinched in the mounting bracketsFor more information: www.lutron.com/technicaldocumentlibrary/window%20systems%20warranty.pdfContact the Lutron Technical Support Center at the numbers provided below or your local Lutron sales representative with questions concerning the installation or operation of the System or this Warranty, or to make a warranty claim. Please provide the exact model number when calling.Lutron, the Sunburst logo, Sivoia, RadioRA, HomeWorks, and Pico are registered trademarks of Lutron Electronics Co., Inc. Worldwide Headquarters | USA Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 USA TEL: 1.610.282.3800 FAX: 1.610.282.3090 Technical Support: 1.800.523.9466 or 1.610.282.6701 Toll Free: 1.888.LUTRON EMAIL: shadinginfo@lutron.com WEB: www.lutron.com/shadingsolutionsEurope Headquarters | United Kingdom Lutron EA Ltd 6 Sovereign CloseLondon, E1W 3JF, UK TEL: +44.(0)20.7702.0657 FAX: +44.(0)20.7480.6899 Technical Support: +44.(0)20.7480.6899 FREEPHONE: 0800.282.107Asian Headquarters | Singapore Lutron GL Ltd15 Hoe Chiang Road#07-03 Singapore, 089316TEL: +65.6220.4666FAX: +65.6220.4333Technical Support: 800.120.4491©2011 LUTRON Electronics Co., Inc.P/N 045-355 REV. ALimited warrantyNumber of years from date of shipmentPercentage of cost of replacement parts credited by LutronUp to 5 100%More than 5 but not more than 8 50%More than 8 0%Restore factory defaults (optional)9Tap 3 times, hold 3 seconds, tap 3 times. e Shade LED blinks for 2 seconds after hold, then for 5 seconds after second triple-tap.Mounting bracketsCellular shadeMounting screwsEndcapsPhillips-head screwdriverCordless drill (optional)5Removing the shade from the bracketsUse a flathead screwdriver to unclip the shade as shown.Enter shade setup mode:Enter shade setup mode: CloseOpenCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseCloseOpen OpenPresetCloseorCloseOpen OpenPresetClose e 7Assigning controlsLEDRechargable batteriesSide viewFCC InformationNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:· Reorient or relocate the receiving antenna.· Increase the separation between the equipment and receiver.· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.· Consult the dealer or an experienced radio/TV technician for help.Note: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this equipment.* This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.

Navigation menu