Luxul Wireless XAP1410 High Power AC1200 Dual-Band Wireless AP User Manual

Luxul Wireless High Power AC1200 Dual-Band Wireless AP

Contents

User Manual.pdf

READ ME FIRSTFold Fold FoldQUICK INSTALL GUIDEHigh Power AC1200Dual-Band Wireless Access PointXAP-1410Includes: One: High Power AC1200 Dual-Band Wireless AP One: Mounting Brackets and Hardware One: PoE Injector and Power Cable One: Ethernet CableREAD ME FIRST - CONTROLLER COMPATIBILITYThis XAP-1410 is compatible with the Luxul Wireless Controller for fast, easy configuration and deployment of wireless networks with multiple APs. nNote: If you’ll be using this AP with a Wireless Controller, refer to the Quick Install Guide included with the Wireless Controller for setup instructions.AP SETUP AND CONFIGURATION1 Physical InstallationThe XAP-1410 access point is designed for simple and ecient installation and can be located one of three ways. First, the included mount is designed to attach directly to several dierent regions’ standard electrical boxes. Second, the XAP-1410 may be mounted on a ceiling or wall without a box by using the included mount as a guide to mark attachment locations. Finally, the XAP-1410 can be placed on a flat surface by attaching the included rubber feet to the mount. cCaution: Attach the rubber feet to the mount and attach the mount to the AP for flat surface placement to avoid overheating and failure. XSingle Access Point Placement: Because the signal generated by the XAP-1410 is omnidirectional, the unit should be located as near as possible to the center of the desired coverage area.XAP-1410 Single AP Coverage Pattern XMultiple Access Point Placement: You may need to experiment with AP placement to optimize the roaming experience. Place APs to ensure adequate coverage, but not so far apart that there is no signal overlap. Adjacent APs should overlap enough that the client device has a good connection to the AP to which it is currently attached, but also sees the next-nearest AP. Ideally, roaming clients should see signal strength of two overlapping APs in the range of -60 to -70 dBm at the midway point between two APs. To learn more about AP placement, visit luxul.com/ap-placement.Ideally, roaming clients should see signal strength of two overlapping APs in the range of -60 to -70 dBm at the midway point between two APsXAP-1410 Multiple AP Coverage and Overlap nNote: Consider using Ekahau HeatMapper to assist with this process, available from www.ekahau.com. Luxul also oers an informative “How-To” video on HeatMapper at luxul.com/how-to-videos.AP SETUP AND CONFIGURATION CONT.2 Connecting Ethernet and PowerEthernet and PowerTo apply power and network simultaneously, simply connect one end of an Ethernet cable to a PoE switch, and the other end to the XAP-1410 PoE port. To connect power and Ethernet separately, first connect an Ethernet cable from the supplied PoE Injector Data & PWR Out port to the PoE port on the XAP-1410. An Ethernet cable length of up to 300 feet can be used.LEGAL AND REGULATORY INFORMATIONNo part of this publication, or any other publication may be modified or adapt-ed in any way, for any purposes without permission in writing from Luxul. The material in this manual is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product. FCC ComplianceThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interfer-ence that may cause undesired operation.FCC ID: W59XAP1410 IC: 8584A-XAP1410FCC Statement—Wireless FCC 2.4GHz & 5GHz 802.11abgnThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020, declares that this Luxul XAP-1410 is in compliance with the essential requirements and other relevant provisions of Directive 1995/5/EC.For a copy of this report send a self addressed stamped envelope to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.Industry Canada (RSS-Gen Issue 4)CAN ICES-3(B)/NMB-3(B) SalesP: 801-822-5450 E: sales@luxul.comTechnical SupportP: 801-822-5450 Option 3 E: support@luxul.com© 2015 Luxul. All Rights Reserved. LUX-QIG-XAP-1410 111715096XAP1410USA1G
Fold Fold FoldNext, connect an Ethernet cable from your Router or Switch to the Data IN port on the PoE Injector. Finally, connect the AC cord to the included PoE Injector, then to the AC outlet. nNote: Category-6 shielded twisted pair is recommended for best results and stable data transmission at the highest data rates. However, CAT5/CAT5e/CAT6 UTP cable can also be used.PoE Injector Setup XData In: Connect an Ethernet cable from your router or switch to the Data In port of the included PoE Injector. XData & PWR Out: Connect an Ethernet cable from the Data & PWR Out port of the included PoE Injector to the PoE Port of the XAP-1410. XAC Power: Connect the included AC Cord to the Power Input of the Included Injector first and then to the AC outlet.PowerSourceFrom yourRouter or SwitchLuxul APDATA INDATA & PWR OUT POEInjectorPoE injector3 Preparing for AccessIP AddressingIf the XAP-1410 is connected to a network with a 192.168.0.X address scheme, and your computer shares a similar address on the same network, you can skip to the next step, Access and Setup. nNote: If another device on your network shares the 192.168.0.10 address, you’ll need to temporarily reassign or remove that device while you configure the XAP-1410.If your network uses an address scheme other than 192.168.0.X, you’ll need to set a temporary static IP address on the computer you’re using for config-uration. To do so, set the IP address of your computer to an address in the 192.168.0.X range, then set the Gateway/Router address to 192.168.0.10 (the default IP address of the XAP-1410).Once you’re finished configuring the AP, you can return your computer’s IP configuration to normal, typically “Obtain Automatically/DHCP.” nNote: Visit http://luxul.com/ip-addressing to learn more about changing your computer’s IP address and getting connected.4 Access and SetupGetting Connected XConnecting Via an Ethernet Device: Use Ethernet cable to connect your computer to the PoE switch or PoE injector to which the XAP-1410 is connected. Ethernet is the preferred method of connection. XConnecting Via a Wireless Device: Connect your client device to the XAP-1410 default wireless network named Luxul1410. The wireless network will run in Open Security mode, so no passphrase is required until Wireless Security is configured. Logging InTo access the AP’s web configuration, open your web browser and enter the AP’s default 192.168.0.10 IP address in the address field. Log in to the AP using the default user name and password: Default IP: 192.168.0.10 Username: admin Password: admin nNote: If another device on your network shares the 192.168.0.10 address, you’ll need to temporarily reassign or remove that device while you configure the XAP-1410. nNote: The XAP-1410 is not a router and will need to be connected to a network with a router in order to deliver Internet access.5 Hardware OperationLED IndicatorsEnclosure: If the green Power LED is on, the XAP-1410 is powered and working. If the Power LED is OFF, the AP is not receiving power or the LED has been turned o in the AP’s web interface. If the green Power LED is blinking, the XAP-1410 is booting. The two blue LEDs indicate indicate each of the 2.4GHz and 5GHz networks are configured and broadcasting.XAP-1410 LED’sPoE Injector: If the PWR LED is On, Power is Connected to the injector. If the PWR LED is O, the injector is not receiving power. Reset ButtonThe Reset button is located underneath the mount and marked RESET. It may be used to reboot the AP or to restore factory default settings.Reboot the AP: With the XAP-1410 powered on, simply press and release the Reset button.Restore Factory Defaults: With the XAP-1410 powered on, press and hold the Reset button for 10 seconds, then release the button and the XAP-1410 will restore factory defaults and reboot. cCAUTION: Holding the Reset button for more than a few seconds will restore the AP to factory default and remove any custom configuration. nERP Statement: The purpose of this product is to create a constant network connection for your devices. It does not have a standby mode or use a power management mode. If you wish to power down this product, please unplug it from the power socket.

Navigation menu