Luxul Wireless XVWP30 Wireless Range Extender User Manual LUX QIG XVW P30 txt indd
Luxul Wireless Wireless Range Extender LUX QIG XVW P30 txt indd
Users Manual
14203 Minuteman Drive, Ste 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
LUX-QIG-XVW-P30-txt 063140843
Simply Connected
Use the XVW-P30 to:
Extend the Coverage Area of an Existing
Wi-Fi Network
Eliminate Wireless Dead Spots
Deliver Reliable Wi-Fi Performance at
Speeds up to 300Mbps
Simplify Wi-Fi Expansion while Minimizing
Setup Time and Costs
Quick Install Guide
XVW-P30
Wireless Range Extender
After entering the password it will take approximately 30 seconds
to fi nish the setup. After 30 seconds, check the Status LED on the
wireless range extender.
If it is solid green, the wireless range extender has been successfully
installed and is now working. If it is fl ashing blue/green there was a
problem with the setup process, most likely the password was not
entered correctly or the wrong wireless router was selected. Reset/
Factory Default the wireless range extender again and re-install.
Parameter: Default Value
Default IP address: 192.168.0.11
Default user name: admin
Default password: admin
Connect a Client Device
The XVW-P30 is now confi gured and extending your wireless network.
Connecting a Client Device
Connecting a Wireless Client Device: Connect the client device
to the SSID used to confi gured the XVW-P30. This will require the
passphrase used when confi guring the XVW-P30.
Connecting an Ethernet Only Device: Simply set the IP Address to
be obtained through DHCP and connect the device to LAN1 or LAN2
WARNINGS AND SAFETY INFORMATION
Verify that the electrical circuits have appropriate grounding and
overload protection.
Verify there is adequate ventilation around the device, and that ambient
temperatures meet equipment operation specifi cations.
The XVW-P30 is designed for indoor use only. DO NOT place this outdoors.
DO NOT install in or near hot or humid places, such as a kitchen or bathroom.
Take care to minimize exposure to excessive heat or moisture.
Small parts and plastic bags used for packaging may be harmful to small
children. KEEP All ACCESSORIES OUT OF THE REACH OF CHILDREN!
The XVW-P30 may become hot when in use for extended
time periods. This is normal and is not a malfunction. DO NOT install where it
will be exposed to paper, cloth or other fl ammable materials.
REGULATORY COMPLIANCE
The device complies with internationally recognized standards covering human
exposure to electromagnetic fi elds from radio devices. This equipment also
complies with FCC radiation exposure set forth for an uncontrolled environment.
In order to avoid the possibility of exceeding the FCC radio frequency exposure
limits, human proximity to the antenna shall not be less than 20 cm (8 inches)
during normal operation.
Unauthorized antennas, modifi cations, or attachments could cause damage and
may violate regulatory approvals. Any
changes or modifi cations not expressly approved by the party responsible for
compliance could void the authority to operate the equipment.
Equipment version marketed in the U.S. is restricted to usage of channels 1-11 only.
Health and Safety Recommendations
Warnings for the use of Wireless Devices: Please observe all warning notices with
regard to the usage of wireless devices
Potentially Hazardous Atmospheres: You are reminded of the need to
observe restrictions on the use of radio devices in fuel depots, chemical
plants etc. and areas where the air contains chemicals or particles (such
as grain, dust, or metal powders).
Safety in Hospitals: Wireless devices transmit radio frequency energy and may
affect medical electrical equipment. When installed adjacent to other equipment,
it is advised to verify that the adjacent equipment is not adversely affected.
910 11 12 13 14
RF Exposure Guidelines
Safety Information: The device complies with internationally recognized
standards covering human exposure to electromagnetic fi elds from radio devices.
Warning: Exposure to Radio Frequency (RF) Radiation:
The radiated output of this device is below the FCC radio frequency exposure
limits. Nevertheless, the device should be used in such a manner that the
potential for human contact during normal operation is minimized.
The end user must avoid any extended human RF exposure directly in front
of the device, up to a distance of 20cm, when unit is on.
When servicing the equipment and selecting a location for the antennas, it
is important to note that a minimum distance of 20cm is required between
personnel and the device or antenna to comply with the radio frequency
exposure limit.
The antenna used for this transmitter must be installed to provide a separation
distance of at least 20cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
The following safety precautions should be observed:
Do not hold any component containing the radio such that the antenna is very
close or touching any exposed parts of the body, especially the face or eyes,
while transmitting.
FCC Statement—Wireless FCC 2.4GHz 802.11bgn
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
FCC Caution: Any changes or modifi cations not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
NOTE: (1)The manufacturer is not responsible
for any radio or TV interference caused
by unauthorized modifi cations to this
equipment.(2) To avoid unnecessary
radiation interference, it is recommended
to use a shielded RJ45 cable
Industry Canada (RSS-Gen Issue 2)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2)this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareilsradio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1)l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5
of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian
information on RF exposure and compliance.
Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la
section 2.5 de RSS 102 et la conformité à l’exposition de RSS-102 rf, utilisateurs
peut obtenir l’information canadienne sur l’exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’au-
cune autre antenne ou émetteur. Cet équipement devrait être installé et actionné
avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
CAN ICES-3 (B) /NMB-3 (B)
Industry Canada ICES-003 Compliance Label:
CAN ICES-3 (*) /NMB-3 (*)
Quick Install Guide
Model Number: XVW-P30
Wireless Range Extender
FCC ID: W59XVWP30
IC: 8584A-XVWP30
© 2014 Luxul. All Rights Reserved.
No part of this publication may be modifi ed or adapted in any way, for any purposes
without permission in writing from Luxul. The material in this manual is subject to
change without notice. Luxul reserves the right to make changes to any product to
improve reliability, function, or design. No license is granted, either expressly or by
implication or otherwise under any Luxul intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in this or any
Luxul product.
DOCUMENT CONVENTIONS
The following alert is used to indicate notable situations:
NOTE: Tips, hints, or special requirements that
you should take note of.
CAUTION: Care is required. Disregarding a
caution can result in data loss
or equipment malfunction.
WARNING!: Indicates a condition or procedure
that could result in personal injury
or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
CONTACT LUXUL
Sales
P: 801-822-5450
E: sales@luxul.com
Technical Support
P: 801-822-5450
E: support@luxul.com
PACKAGE CONTENTS
The following items should be included in the box:
One: XVW-P30 Wireless Range Extender
One: Quick Install Guide
NOTE: If any of the listed items are missing or damaged,
please contact the reseller from whom you
purchased for return/replacement.
WHAT THIS PRODUCT DOES:
Luxul’s XVW-P30 Wireless 300N Range Extender expands the reach of
an existing wireless network—providing Wi-Fi coverage to those hard
to reach dead spots. Designed to plug discreetly into an electrical
outlet, it is well suited for use in both home and small offi ce environ-
ments. The XVW-P30 implements 802.11n technology, delivering up
to 300Mbps speeds and is also compatible with 802.11b/g/n devices.
HARDWARE DESCRIPTION
The XVW-P30 Wireless Extender is designed for optimal performance
as well as simple and effi cient installation. The XVW-P30 can be simply
plugged in to an available power outlet and confi gured to extend the
wireless network in the environment. The XVW-P30 is omni-directional
and will need to be placed where it will extend best in the desired
coverage area.
View of the XVW-P30 Bottom and Right Ports and LEDs
XVW-P30 LEDs
The XVW-P30 has two LEDs, positioned on the front of the device in
the lower right corner. The LEDs are labeled: Power, Status.
XVW-P30 LED Indicators
Indicator Name Description
Power/Green On The power is on
Off No Power check connections
Status/Blue
Green
Green The XVW-P30 is confi gured and
attached to a wireless network
Blue The XVW-P30 is not confi gured
but is broadcasting and ready for
confi guration
Flashing
Blue/
Green
Repeater is not connected to the
wireless router/AP. Check password
or status of wireless router/AP
Bottom Ports
The bottom panel of the XVW-P30 provides two
Ethernet ports to connect Ethernet only devices to the
network remotely.
XVW-P30 Bottom Ports
Right Side Port and Reset
The right panel has the Reset/Factory Default Button and
USB charging port.
XVW-P30 Right Port and Reset
USB Charging Port
The USB on the right panel of the XVW-P30 is a Charge Only Port.
Please note this should charge most USB powered devices but is not
certifi ed by any device manufacturer. (May not support some tablets).
Reset/Factory Default Button
The Reset button is used to clear the current settings of the XVW-P30
and restore factory default settings.
To Restore the Default Settings: With the XVW-P30 powered on, press
and hold the Reset button for 6 seconds. The Status LED turns off, after
a few seconds when the reset button is released and after a the blue
LED will begin to blink. The power LED will stay solid. The XVW-P30 will
be reset to factory defaults.
PREPARING FOR INSTALLATION
System and Power Requirements
Computer or wireless device supporting TCP/IP and equipped with
a Web browser. Supported Web browser versions include the most
current versions of Firefox, Safari, Chrome, and Opera. The Web
browser is used to confi gure the XVW-P30.
Available outlet
Confi guration
Browse for availiable Wi-Fi networks with any standard wireless
device. The SSID (wireless network name) is Luxul-XVW-P30. No
password is required to connect to the range extender.
Open a web browser or plug in a Ethernet device to the ethernet
port and enter 192.168.0.11 – when prompted for a login id and
password, enter admin for both the login id and password.
123456
After logging in, a list of all wireless routers at the current location
will be displayed.
Select the wireless router to be used with the repeater. If you do not
see the wireless router/AP you’re looking for, press the Scan button
to refresh the list, you may have to scroll down.
7
Once the wireless router is selected, a prompt to enter the
appropriate password is displayed. Enter the password and
press Connect
8