Luxul Wireless XWR1200 Dual-Band AC1200 Gigabit Router User Manual

Luxul Wireless Dual-Band AC1200 Gigabit Router

Contents

User Manual

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
Dual-Band AC1200 Gigabit Router
XWR-1200
Includes:
XWR-1200 Dual-Band Wireless AC3100 Gigabit Router
Dual Band Antennas (Two)
Ethernet Cable
Power Adaptor
ROUTER SETUP AND CONFIGURATION
1 Physical Installation
The XWR-1200 Wireless Router is designed for simple and ecient installation.
For horizontal installation, install the rubber feet and position the XWR-1200
on a desk or other horizontal surface with adequate room around the device
for ventilation. For wall or ceiling mounting, simply follow the directions on the
included mounting pattern and use the mounting keyholes on the XWR-1200.
2 Connecting Antennas, Ethernet and Power
Antennas: Ensure all dual-band antennas are installed on the router.
INTERNET Connection: Connect the Ethernet cable from the modem/
router equipment provided by your Internet Service Provider (ISP) to the
black INTERNET port of the XWR-1200.
AC Power: Connect the included AC Adapter to the XWR-1200 first and then
to the AC outlet.
3 Preparing for Access
IP Addressing
The XWR-1200 default LAN IP address is 192.168.0.1. The DHCP server on the
XWR-1200 is configured by default to create a 192.168.0.x network.
Both the default LAN IP address and subnet scheme can be changed. However
for hassle-free plug-and-play installation of other Luxul hardware, we recom-
mend you use the default IP address if possible.
If your client device is set to obtain an address automatically, no further
configuration is required and you can skip to the next step, Access and Setup.
If your computer or device isn’t set to obtain an IP address automatically,
you’ll need to set a temporary static IP address on that device. Set the IP
address of your computer to an address in the 192.168.0.X range, then
set the Gateway/Router address to 192.168.0.1 (the default IP address of
the XWR-1200).
nNote: Visit http://luxul.com/ip-addressing to learn more about
changing your computer’s IP address and getting connected.
4 Access and Setup
Getting Connected
Connecting Via an Ethernet Device: Use an Ethernet cable to connect
your computer to one of the green XWR-1200 LAN ports. Ethernet is the
preferred method of connection.
Connecting Via a Wireless Device: Connect a wireless client device to
one of the XWR-1200 default wireless networks (Luxul_XWR1200 or
Luxul_XWR1200_5G). Both Wireless networks will run in Open security
mode, so a passphrase will not be required until wireless security is
configured.
Open a web browser, enter 192.168.0.1, then log in to the router using the
default user name and password and proceed with configuration:
Default IP: 192.168.0.1
Username: admin
Password: admin
nNOTE: If another device on your network shares the 192.168.0.1
address, you’ll need to reassign that device a dierent IP
address to configure the XWR-1200.
nNOTE: Only devices that support the 5GHz frequency will see the
default Luxul_XWR1200_5G wireless network.
Sales
P: 801-822-5450
E: sales@luxul.com
Technical Support
P: 801-822-5450 Option 3
E: support@luxul.com
LUX-QIG-XWR-1200-v1 07271610
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply
Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and
registered trademarks are property of their respective holders.
Fold Fold Fold
5 Advanced Configuration
Configuring the XWR-1200 as a Wireless Controller
The XWR-1200 can manage up to two additional access points to enable
wireless client roaming and simple configuration. To enable this feature,
ensure one or two compatible access points are connected to the same
network as the XWR-1200, then select Wireless Controller from the XWR-
1200 web configuration interface. Follow the online help to add the access
point(s) to the profile.
XWR-1200 as a Controller
Other Advanced Configuration
For more information on configuring advanced features such as DDNS,
VPN, etc., refer to the support resources at luxul.com.
6 Hardware Operation
XWR-1200 Front Panel LED Indicators
Indicator Name Status Function
5GHz ON A 5GHz wireless network is
broadcasting.
2.4GHz ON A 2.4GHz network is broadcasting.
1-4 LED ON A device is connected to the
corresponding Ethernet port.
FLASHING Data packets are being transmitted
to the connected device.
Internet
LED
ON XWR-1200 is connected to the ISP.
FLASHING Data packets are being transmitted
USB
LED
ON A USB-enabled device is connected
and configured.
System
LED
ON The XWR-1200 is booting.
FLASHING The XWR-1200 is operating normally.
OFF The XWR-1200 is not booting.
Power
LED
ON Power is applied to the XWR-1200.
OFF Power is not applied to the
XWR-1200.
Front Panel
XWR-1200 Front Panel View
Rear Panel
XWR-1200 Rear Panel View
Antenna Ports: 4 RPSMA female antenna ports to connect the
included antennas.
nNOTE: All four antennas should be installed prior to powering up
the XWR-1200 and are required for optimal performance.
Power Input: Power adapter included.
nNOTE: To reboot the router, disconnect the power adapter,
wait 10 seconds and reconnect the power adapter.
WAN Port: (1) black RJ-45 Ethernet Port for Internet connection.
LAN 1 - 4 Ports: (4) green RJ-45 Ethernet ports for connecting to the
local network.
nNOTE: A Luxul switch is recommended in conjunction with the
XWR-1200 to increase the number of local ports available.
Reset Button: Used to restore factory default settings.
cCAUTION: Holding the Reset button longer than 10 seconds will
result in a factory reset.
To restore factory defaults, press and hold the Reset button until the
System LED stops flashing (approximatly 20 seconds). A factory reset
will take one minute or more to complete. A successful factory reset is
indicated when all of the Port LEDs flash once. When the System LED
starts flashing again, the unit is ready.
cCAUTION: Resetting the XWR-1200 to factory defaults will remove
all custom settings.

Navigation menu