MAGIC CHEF Microwave/Hood Combo Manual L0803304
KOG-574R L0803304
User Manual: MAGIC MAGIC CHEF Microwave/Hood Combo Manual MAGIC CHEF Microwave/Hood Combo Owner's Manual, MAGIC CHEF Microwave/Hood Combo installation guides
Open the PDF directly: View PDF .
Page Count: 8
Download | |
Open PDF In Browser | View PDF |
Microwave Oven Installation Manual Introduction Your Over-the-Range ruicrowave oven corues complete with an installation instruction kit which contains the followilrg tln'ee pieces of information required to install it. NOTE: I. This installation instruction booklet, III. Instead of The Wall Monnt Template, IT IS RECOMMENDED THAT TWO complete with diagrams on prepaxing yonr Wall Monnting Plate, used to locate the cabinets and microwave oven for PEOPLE INSTALL THIS PRODUCT. monnting plate holes and to locate the installation. horizontal exhaust location. Please read all of the instructions IMPORTANT: The Top Cabinet Template, used to locate KEEP INSTRUCTIONS FOR LOCAL thoronghly before installing your the power cord clearance hole, cabinet nlicrowave oven. ELECTRICAL INSPECTOR'S USE. ruounting holes and the vertical exhaust location. Important Safety Information Grounding Instructions This appliance must be _ounded. In the event of an electrical short circuit, gounding reduces the risk of the electric shock by providing an escape wire tbr the electric cm'rent.This appliance is equipped with a cord having a m'ounding wire with a g'ounding plug. The plug must be plugged into an outlet that is properly installed and _ounded. WARNING - Improper use of the grounding can result in a risk of electric shock. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly _ounded, and either: cord that has a 3-blade _'ounding plug, and a 3-slot receptacle that will accept the plutg on the appliance. The marked rating of the extension cord shall be equal to or greater than the electrical rating of the appliance, or Do not use an extension cord. 2) If the power supply cord is too short, have a qualified ".\_ electrician or serviceman \, install an outlet near the appliance. 1) If it is necessary to use an extension cord, use only a 3-wire extension Safety Instructions This product requires a three prong _'ounded receptacle. The installer must pertbrm a _'ound continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly _ounded. If not properly grotmded, or if the outlet box does not meet the electrical requirements noted, (under ELECTRICAL REQUIREIVIENTS),a qualified electrician should be employed to correct any deficiencies. CAUTION: FOR PERSONAL SAFETY, REMOVE HOUSE FISE OR OPEN CIRCUIT BREAKER BEFORE BEGINLNING INSTALLATION TO AVOID SEVERE OR FATAL SHO(K INJI RY. CAUTION:FOR PERSONAL SAFETY, THE MOUNTING S[_ACE _HTST BE CAPABLE OF SUPPORTING THE CABINET LOAD, LNADDITION TO THE ADDED WEIGHT OF THIS 85 POI_'D PRODUCT, PLUS ADDITIONAL OVEN LOADS OF IP TO 50 POUNDS OR A TOTAL WEIGHT OF 135 Power supply cord a) A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord. b) Longer cord sets or extension cor& are available and may be used if care is exercised in their use. c) Ifa long cord or extension cord is used: 1) The marked electrical rating of the cord set or extension cord should be at least as _m'eatas the electrical rating of the appliance. POUN3)S. CAUTION: FOR PERSONAL SAFETY THIS PRODUCT CANLNOTBE INSTALLED TO CABINET ARRANGEMENT'S SUCH AS AN ISLAND OR A PENINSULA. IT MUST BE MO[ NTED TO BOTH A TOP ( ABINET AND A WALL. Electrical Requirements Product rating is 120 volts AC, 60Hertz, 14.6 amps, and 1.60 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency. Wke size nmst confol_ to the requirements of the National Electric Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate 20ampere branch circuit single _'ounded receptacle. The outlet box should be located near the cord entry point. The outletbox and supply ckcuit should be installed by a qualified electrician and conform to the National Electric Code or the prevailing local code. 2) The extension cord nmst be a grounding type 3-wire cord, and 3) The longer cord should be arranged so that it will not &ape over the counter top or tabletop where it can be pulled on by children or tripped over unintentionally. This over-the-range oven was designed for use over ranges no wider than 30inches. It may be installed over both gas and deetrie cooking equipment. Installation Hardware Parts List 1. Lag screws 1/4" x 2" ( 3 EA ) 2. Toggle Bolts 3" ( 3 EA ) 3. Spring Loaded Toggle Nuts ( 3 EA ) 4. Cabinet Mounting Bolts 1/4" x 31/8" ( 3 EA ), 1/4" x 2" (3 EA) 5. Washers 3/4" ( 3 EA ) 6. Gromment ® 7. Damper 8. Foam Tape ( 2 EA ) 9. Top Cabinet Template 10. Wall Template Tools The %llowing installation The following is a list of parts you may need for installing your Over-the-Range microwave oven. You will find them packaged inside the microwave cooking cavity. Remove all parts from the oven cavity and compare them with the parts Mounting list and illustration to be sure that none are missing. Use this time to become familiar with each piece. tools of your Phillips screwdrivers, Motor, 1/2" & 5/8" Drill needed), or Jig Saw, Pencil, & Duct Drill Bits & 3/16" opening, Tin Snips Measure, (if Paper Tape. Your Over-the-Range microwave oven requires mounting space on a wall as shown. 1. A minimum of 30" betaveen wall hung side cabinets is required for installation. Make sure the bottom '1 more Tape %r oven. Space OTR 30" Electric Wood Bit, Saw to cut exhaust (if needed) Tape may be needed microwave edge of the top cabinet is at least 66" from the floor and 30" from the than from cooking surface cooking surface. 2. For easier access to the hood lamp, the bottom of the microwave oven 66" O£ lllore flora tile floorto the topof the should be at least 2" above the range backsplash. 3. If you are going to vent your microwave oven to the outside, see exhaust duct preparation. 4. Designed to be installed in 30" wide cabinet opening. Wall Construction Your Over-the-Range microwave oven should be mounted against and supported by a flat, vertical wall. Wall construction should be a minimum of 2" x 4" wall studding and 3/8" or more, thick drywall or plaster/lath. The oven must be attached to a minimum of one 2" x 4" wall stud. For proper installation the wall must be capable of supporting the cabinet load plus a minimum of 135 pounds, (the 85 pound weight of the microwave oven and load weight allowance of 50 pounds.) To find studs, use one of the following methods: I. Stud finder a magnetic Usually 16"or 24" II. Using a hammer, tap lightly across the mounting to find a solid sound. This will indicate a stud r 3/8" DiTwall or Plaster / Lath _/_"'_: 2" X 4" wood studor ::metal stud (25 gauge or thicke*) Log sclews must be installed in these area Hood Exhaust : device which locates nails. surface installation. After locating the stud(s), the center can be found by: Probing the wall with a small nail to find the edges of the stud and then placing a mark halfway between the edges. The center of any adjacent studs should be 16" or 24" from this mark. iI Duct Outside ventilation requires HOOD EXHAUST DUCT. Read the tbllowing carefully. EXHAUST CONNECTION: The hood exhaust has been desigled to mate with a standard 3-1/4" x 10" rectangular duct. If round duct is required, a rectaugular-toround trausition adapter nmst be used. Do not use less thau a 6" diameter duct. REAREXHAUST:If rear or horizontal exhaust is to be used, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is comstmcted by leaviug euough space between wall studs to accolmnodate exhaust. MAXIIVRJMDUCT LENGTH: For satisfactory air movement, the total duct length of 3-1 '4" x 10" rectaugular or 6" diameter round duct should not exceed 140 feet of epuNalent duct run. ELBOWS, TRANSITIONS, WALL AND ROOF CAPS, etc., preseut additional resistance to air flow and are equivaleut to a sectiou of straight duct which is longer than their actual physica! size. When calculatiug the total duct len_h add the equivaleut lengths of all transitions and adaptors plus the leugths of all straight duct sections. The diagram below shows the approximate feet of equivalent length of some typical ducts. ROOF CAP(24FT) % 45° ELBOW(5FT) ADAPTOR (5FT) 90 ° ELBOW(10FT) 45° ELBOW(5FT) WALL CAP (40FT) 90° ELBOW(25FT) Ventilation system Instructions Your Over-the-Range microwave oven is designed for adaptation to the following three types of ventilation. Select the type of ventilation required for your installation and proceed to the appropriate section. A. Horizontal Ventilation A-1. Ventilation motor System This blower motor has a damper and your microwave oven is shipped assembled for a Recirculation Application. Step.1 * Remove the screws (11)) for opening the blower motor cover and save screw. Remove cover. Step .2 * Remove the screw (_) for Blower attachment screw. * Lift blower unit out of mounting location. CAUTION: Do not pull or stretch blower wiring. Vel_ical duct configulation Step .3 Step .4 Roll the blower unit so that the fan blade openings are facing back ( rear of unit ). * If you want VERTICAL, roll the blower unit so that the fan blade openings are facing upward. Carefully match the exhaust opening location oven and reinstall the screws (]).,: 2)). CAUTION: Wires to blower unit must be routed avoid to pinching, before reinstallation of cover plate. Horizontal Veltical duct configmation and save duct configmation of the microwave A-2. Install the Mounting Plate Step. 1 Setup position a. Draw a line down the middle of the studs(See the Wall Construction_ b. Draw a vertical line on the wall at the center of the 30" wide space. page 3) NOTE: Use the wall template for the rear wall. Reference \Vail Template prior to proceeding. Installation of this product require TXVO persons. Step. 2 Drilling Reference the Wall Template. Step. 3 Install the damper Fit the damper into the house duct. Be sure that the damper I hinge is on the top and the damper Wall _jjl/, swings free into the wall outlet. _. "" - 21222____o House Duct Take the 28" foam tapes and remove the paper from sticky side. Press the sticky side onto the front edge of the damper. the foam tape) Step. 4 Tightening the screws To Attach the mounting plate to the wall using the toggle bolt assemblies Spacing more than Wall thickness a. Insert toggle bolts through mounting (Don't stretch and/or lag screws: plate at required locations and add the spring loaded toggles. Be sure you leave space at least the thickness of the wall between the mounting plate and the end of the toggle nut, (in closed position). If you do not leave this space, the toggle nut will not open on the other side of the wall. b. Position mounting plate on wall and insert toggle bolt assemblies start the lag-screw(s) through the wall stud(s). c. Next, secure mounting plate to the wall by tightening d. Drill 3/16" diameter lag screw hole(s), into one or more wall studs. (Remember, you must have at least one lag screw into a wall smd.)For location refer to WALL CONSTRUCTION see page 3 through the drywall holes or toggle bolt assemblies or lag screw(s). stud e. Tighten the lag screw(S) into wall stud(S) Diy wail Mortaring plate A-3. Mounting NOTE: microwave IT IS VERY IMPORTANT PREPARATION THAT oven THIS OVEN BE INSTALLED BY TWO PEOPLE. OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. • Read the instructions on the TOP CABINET TEMPLATE • Tape it underneath the top cabinet • Drill the holes, following the instructions on the template CABLNET Step. 1 Protect the top of your range by placing a portion of the carton or some other heavy material over the cooking surface before mounting your oven. Step. 2 Hang the unit on the two tabs at the bottom of the mounting plate. Step. 3 Thread power cord through the hole at the bottom of the top cabinet. Swing the unit upward to meet the top of the mounting plate and hold secure. Step. 4 Insert the 2 bolts through 2 flat washers into holes on top cabinet floor. Tighten screws to close the gap between top cabinet and the microwave oven. NOTE: MICROWAVE MOUNTING BOLTS. OVEN MUST BE SECURED WITH TWO Dress power cord nearly in top cabinet. Install the _ease filters. * Using filler block for recessed bottom cabinet Insert a bolt, with a 3/4" washer into one of the holes drilled previously in the top cabinet floor. (D & E on Top Cabinet Template.) \Vashel Top cabinet nlOtlll_illg sclew Cabinet Cabinet flont bottom shelf Microwave oven top B. Vertical Ventilation System B-1. Ventilation motor See the page 4, A-1. Ventilation motor, step 3. B-3. Mounting Microwave oven See the page 6, A-3. Mountingthe Microwave oven. B-2. Install the mounting plate See the page 5, A-2. Install the mounting plate. • Yon need not pertbnn the step2 and step 4; Horizontal ventilation only. B-4. Install the Damper For the vertical exhaust open the top cabinet and attach the damper to the microwave through the cabinet bottom. For front to back or side to side adjustment, slide the damper as needed. With the damper out, twist the damper to fit under the flaps of the blower plate. Replace the damper and make sure it will move easily by the force of the exhaust air. Be sure to square the comers After the microwave on the hinge oven is installed, ends. Pull the house duct down to conncet to the damper. Install the _ease filters. C. Recirculation Ventilation System Your over the range microwave oven has been provided with a charcoal filter for a recirculation the charcoal filter is required, contact your MAYTAG authorized dealer. C-1. Ventilation motor This ventilation motor has been assembled for Recirculation exhaust. Chalcoal C-2. Install the Mounting plate See the page 5, A-2. Install the mounting plate. • You need not perform the step 2 and step 4; Horizontal only. C-3. Mounting Microwave oven See the page 6_ A-3. Mounting the Microwave * You need not use damper for recirculation. C-4. Install the Charcoal Filter ventilation oven. Glille. filter * Remove the screws on the front of the grille and remove * Install the charcoal filter. the grille. * Replace the grille and screws. * Install the grease filters. Checklist 1. 2. 3. 4. for Installation Make sure oven has been installed according Remove all packing material from the oven. Plug in power cord. Read Use and Care manual. 5. Keep installation instructions and template to these instructions for the local electrical and top cabinet template. inspector's use. venting application. If replacement of
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 8 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Tue Mar 25 06:29:39 2008 Author : Title : Subject :EXIF Metadata provided by EXIF.tools