MEIAN Technology MC-235R WIRELESS PIR DETECTOR User Manual MC 235R DMT Q20100506

Shenzhen Meian Technology Co.,Ltd . WIRELESS PIR DETECTOR MC 235R DMT Q20100506

Users Manual

MC-235R WIRELESS PIR DETECTOR MC-235R is PIR intrusion detector with Pet immunity. It adoptsdigital microprocessor control technology. By using refined cylindrical FRESNEL lens in PIR section, it has high energy receivingefficiency and high sensitivity and false alarm immunity. With advanced patented software technology, It well settles the false alarm and malfunction caused by other interference factors. It hasultra-high detecting sensitivity and excellent anti-False alarm performance. It is widely used in various indoor applications by choosing proper pulse quantity. Special battery-saver feature and working life is up to more than 2 years. Model：MC-235R Detection distance：9m（25℃ ） Emitting distance：120-150m（in open area）Operating voltage：6V(4 *1.5 V)Infrared section(as shown in the figure)Optical lens dataInfrared area：11+5 （typical）Max.coverage：9 m*9m (23*46feet)/90°Emitting frequency：433MHzAlarm indication：LED flashes for seconds.Mounting：Wall or corner mountable，2.0-2.4m above groundOperating environment：Operating temp：-10℃-50℃ （14℉-122℉ ）Storage Temp.：-20℃-60℃ （-4℉-140℉ ）Anti-white light（indoor） ：>9000LUXDimensions:（L*W*H）94*62*53mm3.Installation2．Specification3.1NotesWall mounting wide -angle lense view Side view2. 5 m1. 5 m0. 6 m6m4m2m7. 523 3 016,52,,,8,0,,,XXXX9mDo not face the cold andheat source directlyDo not face the sunlightdirectlyKeep wiring away from high-voltage cableDo not install on unstable objectDo not face themetal wall directly1.IntroductionP/ N 201 10 5 06 - 2LensePIRTamper switch01.5m1.5m3m3m4.5m4.5m10m8m6m4m2m00JumperswitchXDIP switchCurrent consumption： Static≤30μA，Alarm≤20mA（433MHz） 3.2 pet-immunity guidebook The installation height of 2.2m to 2,4m is available pet-immunity height2.2- 2 . 4 m2.2- 2 . 4 m≤15K gthe pet is smaller than 15kgthe top of the detecting area is the non-pet-immunityareaNOOK2.2- - 2 . 4 m2.2- 2 . 4 m≤20K g15。the pet is smaller than 20kgprevent direct the places where the pets can clamb up X3.3 Illustrated installationWall mount②.Non bracket mounting：2.0-2.4m above the ground，Wall, 0 bracket or 45 corner mountable B. Mark screw hole and drill C. Insert two expandable dowel and attach the base to the wall with two screws.D. Replace the battery and cover ①.Dismantle procedure: A. Remove the screw by srewdriverBracketmount0 4 5mount Corner
8. Customer Service① Set as Test Mode to proceed walk-test,pulse count set as 1,2 or 3 ③ Do walk-test in opposite direction to confirm the boundary of both sides, Make sure the detection centre pointing to the centre of protected area.。④ Make sure the detection centre at the proper place. Should properly adjust the detection area if you can not get an ideal detection area.② Walk across the far edge of coverage area at the speed of 1 step/second(about0.75m/s) The LED will flash for seconds then alarm（as shown in the right figure）7. Walk test in coverage area:⑤ After adjust the detection angle , should redo the walk test as above.⑥ Please change TEST mode to NORMAL mode after the Walk-test . 4.DIP switch functions:MC-235R can set three modes as follows:Test Mode：Emitting alarm signal once detector is triggered. No time-lag between two emissions. Default mode for installing test.Power-saver mode：Detect every 3 minutes. Send detection signal of detector and battery status Coding Mode：Press tamper switch for more than 3 seconds and send an identification code to receiver. MC-235R can choose 3 kinds of pulse as follows:1-pulse： Alarm 1-pulse. 2-pulse: Alarm 2-pulse。3-pulse： Alarm 3-pulse (Factory defaul) 。Higher pulse counting and lower catch performance and can avoid false alarm 3214DIPONModes of DIP switch 3&4:MODEON OFF TESTOFF ON POWER-SAVEROFF OFF CODING34 1 2MODE1-Pulse2-Pulse3-PulseON ON OFF OFF OFF OFF Our products are very reliable，but for some special reasons, the working performance will be limited in certain range. We here list some cases as follows： ①. The voltage of control panel is not stable； ②. Low-voltage of the detector.For any help please contact with our company and your could visit our website for more information. Warning: We are not responsible for the problem caused by improper operation by users!5. Coding method between detector and control pane and tamper switch setting：① Coding set：Install the battery，LED flashes，whenthe detector gets stable after seconds，press tamper switch for more than 3seconds and detector will send awireless signal. If the control panel receives the signal and get the responsesound then code successfully. Pleaserefer to control panel manual for details. ① Push here to coding set6.Detection distance adjustment and battery changePull out the base cover and changebattery. Please pay attention to thepositive and negative.Polarity② Jumper② If short circuit of the jumper as shownthen tamper alarm function invalidFCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.once detector is triggered.The detector checks its batteries conditions when the batteries in low voltage then it will transmit signals to warning users to replace the batteries. It only transmit once to warn users.

Navigation menu