MEIAN Technology MC-235R WIRELESS PIR DETECTOR User Manual MC 235R DMT Q20100506

Download:
Mirror Download [FCC.gov]
Document ID	2295228
Application ID	NCtBLpGGy0tV9tKtDWhmEA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	60.71kB (758899 bits)
Date Submitted	2014-06-16 00:00:00
Date Available	2014-06-16 00:00:00
Creation Date	2014-04-28 19:19:10
Producing Software	Corel PDF Engine Version 15.0.0.486
Document Lastmod	2014-06-13 13:58:31
Document Title	MC-235R DMT 英文Q20100506
Document Creator	CorelDRAW X5
Document Author:	Administrator

MC-235R WIRELESS PIR DETECTOR
1.Introduction
MC-235R is PIR intrusion detector with Pet immunity. It adopts
digital microprocessor control technology. By using refined
cylindrical FRESNEL lens in PIR section, it has high energy receiving
efficiency and high sensitivity and false alarm immunity. With
advanced patented software technology, It well settles the false
alarm and malfunction caused by other interference factors. It has
ultra-high detecting sensitivity and excellent anti-False alarm
performance. It is widely used in various indoor applications by
choosing proper pulse quantity. Special battery-saver feature
and working life is up to more than 2 years.
DIP
switch
PIR
Jumper
switch
Tamper
switch
Lense
2．Specification
Model：
MC-235R
Detection distance：9m（25℃）
Emitting distance：120-150m（in open area）
Operating voltage：6V(4 *1.5 V)
2m
4m
6m
8m
10m
4.5m
3m
1 .5 m
Mounting：
Wall or corner mountable，2.0-2.4m above
ground
Current consumption：
Static≤30μA，Alarm≤20mA（433MHz）
Infrared section(as shown in the figure)
Optical lens data
Infrared area：11+5 （typical）
Max.coverage：9 m*9m (23*46feet)/90°
Emitting frequency：433MHz
Alarm indication：LED flashes for seconds.
1.5m
3m
4. 5 m
Operating environment：
Operating temp：-10℃-50℃（14℉-122℉）
Storage Temp.：-20℃-60℃（-4℉-140℉）
Wall mounting wide -angle lense view
7 .5
2 .5 m
1 .5 m
0 .6 m
2m
16
4m
30
9m
23
6m
Anti-white light（indoor）：>9000LUX
Dimensions:（L*W*H）94*62*53mm
Side view
3.Installation
3.1Notes
Do not face the cold and
heat source directly
Do not face the sunlight
directly
Do not install on
unstable object
Keep wiring away from
high-voltage cable
Do not face the
metal wall directly
3.2 pet-immunity guidebook
NO
OK
2.2--2.4m
the top of the detecting
area is the non-pet-immunity
area
prevent direct the
places where the pets can
clamb up
3.3 Illustrated installation
①.Dismantle procedure:
。
15
≤2 0 K g
2.2-2.4m
the pet is smaller
than 20kg
≤1 5 K g
2.2-2.4m
the pet is smaller than 15kg
B. Mark screw hole and drill
45 0 Corner
mount
P/N 20110506-2
The installation height of
2.2m to 2,4m is available
pet-immunity height
②.Non bracket mounting：2.0-2.4m above the ground，Wall,
bracket or 45 0 corner mountable
Wall mount
A. Remove the screw by srewdriver
2.2-2.4m
Bracket
mount
C. Insert two expandable
dowel and attach the
base to the wall with
two screws.
D. Replace the battery and
cover
4.DIP switch functions:
MC-235R can choose 3 kinds of pulse as follows:
1-pulse： Alarm 1-pulse.
2-pulse: Alarm 2-pulse。
3-pulse： Alarm 3-pulse (Factory defaul) 。
Higher pulse counting and lower catch performance
and can avoid false alarm
DIP
ON
ON
OFF
MODE
OFF 1-Pulse
ON
MC-235R can set three modes as follows:
Test Mode：Emitting alarm signal once detector is triggered.
No time-lag between two emissions. Default mode
for installing test.
Power-saver mode：Detect every 3 minutes. Send detection
signal of detector and battery status once detector
is triggered.
Coding Mode：Press tamper switch for more than 3 seconds
and send an identification code to receiver.
2-Pulse
Modes of DIP switch 3&4:
OFF OFF 3-Pulse
5. Coding method between detector and
control pane and tamper switch setting：
① Coding set：
Install the battery，LED flashes，when
the detector gets stable after seconds，
press tamper switch for more than 3
seconds and detector will send a
wireless signal. If the control panel
receives the signal and get the response
sound then code successfully. Please
refer to control panel manual for details.
② If short circuit of the jumper as shown
then tamper alarm function invalid
MODE
ON OFF TEST
OFF ON
POWER-SAVER
OFF OFF CODING
6.Detection distance adjustment and battery change
The detector checks its batteries conditions when the batteries in
low voltage then it will transmit signals to warning users to
replace the batteries. It only transmit once to warn users.
Polarity
Pull out the base cover and change
battery. Please pay attention to the
positive and negative.
② Jumper
① Push here to
coding set
7. Walk test in coverage area:
① Set as Test Mode to proceed walk-test,pulse count set as 1,2 or 3
② Walk across the far edge of coverage area at the speed of 1 step/second(about0.75m/s)
The LED will flash for seconds then alarm（as shown in the right figure）
③ Do walk-test in opposite direction to confirm the boundary of both sides, Make sure the
detection centre pointing to the centre of protected area.。
④ Make sure the detection centre at the proper place. Should properly adjust the detection
area if you can not get an ideal detection area.
⑤ After adjust the detection angle , should redo the walk test as above.
⑥ Please change TEST mode to NORMAL mode after the Walk-test .
8. Customer Service
Our products are very reliable，but for some special reasons, the working performance will be limited in certain range.
We here list some cases as follows：
①. The voltage of control panel is not stable；
②. Low-voltage of the detector.
For any help please contact with our company and your could visit our website for more information.
Warning: We are not responsible for the problem caused by improper operation by users!
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2014:04:28 19:19:10+08:00
Creator Tool                    : CorelDRAW X5
Modify Date                     : 2014:06:13 13:58:31+08:00
Metadata Date                   : 2014:06:13 13:58:31+08:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : MC-235R DMT 英文Q20100506
Producer                        : Corel PDF Engine Version 15.0.0.486
Document ID                     : uuid:7b749933-674a-4b29-94a0-59574be96eb8
Instance ID                     : uuid:5e4ca428-25c5-45cd-bccd-2531dd5c537b
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 2
Author                          : Administrator

EXIF Metadata provided by EXIF.tools