MEIAN Technology MC-535R Wireless digital PIR detector User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3418159
Application ID	gQx9M8NOlAEsXUliJamv+g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	57.74kB (721792 bits)
Date Submitted	2017-06-08 00:00:00
Date Available	2017-06-08 00:00:00
Creation Date	2017-05-11 10:21:37
Producing Software	Corel PDF Engine Version 14.0.0.701
Document Lastmod	2017-06-08 15:50:38
Document Title	MC-535R 红外探测器 锂电池 英文 PN20170428A01.cdr
Document Creator	CorelDRAW
Document Author:	Administrator

Wireless digital PIR detector User Manual
1.Introduction
MC-535R is a PIR intruder detector for indoor use.It adopts
precision cylindrical FRESNEL lens, can effectively improve
energy saving, with high sensitivity and free of false alarm. By
using advanced patented software, it can identify the real
intruder and other interference factor which may result in false
alarm. Pulse counting can be adjustable. It is widely use in
various indoor applications, Built-in big capacity lithium
battery, power-save mode.Its working life is up to 2 years or
above.
2.Specifications
Battery container
Tamper switch
DIP switch
LED
PIR
Fig.1 Appearance
Fig.2 Internal Structure
9m
Installation：
①wide-angle: 12M * 12M detection angle of 110 degrees
②flat curtain: 12M * 2M detection angle of 3 degrees
③ceiling curtain: 6M * 1M detection angle of 3 degrees
④Installation height： 2~2.3M
6m
Model:MC-535R
3m
Maximum detection distance: 12m/25℃
Emitting distance: 120m (in the open area)
Infrared distance:12m
3m
Working voltage: DC3V, 1*CR123A lithium battery
6m
Alarm current: ＜20mA
9m
8m
4m
12m
Quiescent Current: 16µA~17µA
Wall mounting wide
Infrared section (as shown at right)
angle lens view
Optical lens data sheet
7.5
Infrared area: 12 × 4 (typical)
Maximum coverage: 12m * 12m (39 * 39 feet) / 90 ° ,
16
23
8m
4m
12m
Emitting distance : 433MHz
Side view
Alarm indication: The LED indicator is on for 2~3 seconds.
Operation condition:
2.3m
1.5m
0.6m
Operation temperature:-10℃~60℃﹤95%RH
Storage temperature:20℃ ~60℃(4℉ ~140℉)
Size:：86(L)*45(W)*36(H)mm
3.Installation
3.1 Notes
Don't face cold or
heat directly
Don't face the sun
-shine directly
Don't install near
electric cables
Don't install on a
unstable base
Don't face metal wall
3.2 Installation location
Use double-sided adhesive to install the detector 2 to 2.3 meters
Detector
from the ground, pay attention to the installation of PIR down.
Installation can choose to install wide-angle, flat
curtain, ceiling curtain three ways, different installation
methods corresponding to the installation height and
detection angle is different (see "2, specifications and
technical parameters").
3.3 Change battery:
2~2.3m
B, remove the old battery, according to the marked polarity of the
battery correctly into the battery.
A, with a word screwdriver
light top groove, pull out the
bottom cover, remove the
bottom cover.
P/N:20170428A01
-1-
C, the side of the shell with a battery up one end, the bottom cover
with a button at one end down the face of the shell to close and
pull the bottom cover into the face shell.
4. DIP switch function description
Switch serial
number
OFF
High sensitivity( default)
Alarm delay 5 second
Alarm delay 5 minutes(default)
LED is off
LED is on(default)
ON
ON
KE
Low sensitivity
5. Coding method between detector and panel:
Coding setting:
①Set the detector as normal mode, place the battery and LED will flash
seconds,set the panel as coding mode(panel coding setting pls refer
to panel manual), within 3 seconds when press the confirm key of the panel
Wave hand near the front side of detector, it will send a alarm signal
to the panel, if the panel sounds a response then code successfully.
②Enter the address number to code with panel,set the panel as manual coding
Tamper switch
mode and enter the 9-digit address number,this method is much better.
6. Walking test in coverage area:
①Set the detector as test mode to proceed walk-test.
②Walk accross the far edge of coverage area at the speed of 1step/second
(about 0.75m/s). The LED will flash for seconds then alarm(see the right figure).
③Do walk-test in opposite direction to confirm the boundary of both sides.Make
sure the detection centre pointing to the centre of protected area.
④Make sure the detection centre at the proper place,should properly adjust the
detection area if you can not get an ideal detection area.
⑤After adjust the detection angle, should re-do walk test as above.
⑥After passing the test, be sure to set the alarm delay to 5 minutes mode, otherwise it will
affect the battery life。
7.Customer Service
For any help please contact with our company and you could visit our website for more information
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help .
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
-2-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : Administrator
Title                           : MC-535R 红外探测器 锂电池 英文 PN20170428A01.cdr
Create Date                     : 2017:05:11 10:21:37+08:00
Creator Tool                    : CorelDRAW
Modify Date                     : 2017:06:08 15:50:38+08:00
Metadata Date                   : 2017:06:08 15:50:38+08:00
Producer                        : Corel PDF Engine Version 14.0.0.701
Document ID                     : uuid:8e568950-d870-460b-b405-e4fb8c566430
Instance ID                     : uuid:8e1b3146-caf7-422c-9065-d412f23fe7a2
Page Count                      : 2
Author                          : Administrator

EXIF Metadata provided by EXIF.tools