MITSUBISHI Projection/Digital 42 And Above TV Manual L0208263
User Manual: MITSUBISHI MITSUBISHI Projection/Digital 42 and above TV Manual MITSUBISHI Projection/Digital 42 and above TV Owner's Manual, MITSUBISHI Projection/Digital 42 and above TV installation guides
Open the PDF directly: View PDF 
.
Page Count: 79
| Download | |
| Open PDF In Browser | View PDF |
_
MITSUBISHI
THE BIG SCREEN COMPANY _"
RISK OF ELECTRIC
DO NOT OPEN
CAUTION:
TO REDUCE
SHOCK
THE RISK OF ELECTRIC
SHOCK,
COVER (OR BACK).
NO USER SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
DO NOT REMOVE
PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the
user of the presence of uninsulated "dangerous voltage" within the product's enclosure that
may be sufficient magnitude to constitute a risk of electric shock.
The exclamation
point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing)
instructions in the literature
panying the appliance.
Warning:
To avoid permanently imprinting a fixed image onto your TV screen, please do not display the
same stationary images on the screen for more than 15% of your total TV viewing in one week. Examples
of stationary images are letterbox toplbottom
bars from DVD disk or other video sources, side bars when
showing standard TV pictures on widescreen TV's, stock market reports, video game patterns, station
Iogos, web sites or stationary computer images. Such patterns can unevenly age the picture tubes causing
permanent damage to the TV. Please see page 51 for a detailed explanation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions,
may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
connected.
• Consult the dealer or an experienced
radiolTV technician for help.
Changes or modifications
this equipment.
not expressly
approved
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
OR MOISTURE.
CAUTION:
TO PREVENT
ELECTRIC
SHOCK,
by Mitsubishi
SHOCK,
MATCH WIDE BLADE
could void the user's authority
DO NOT EXPOSE
is
to operate
THIS APPLIANCE
TO RAIN
OF PLUG TO WIDE SLOT, FULLY INSERT.
NOTE TO CATV SYSTEM INSTALLER:
THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO
ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES
FOR THE PROPER GROUNDING
AND, IN PARTICULAR,
SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED
TO THE
GROUNDING
SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS
PRACTICAL.
IMPORTANT
SAFEG UARDS .............................................................................
Appendix A: Bypassing the V-Chip Lock ...........................................................................................................
Appendix B: High Definition Inputs Connection Compatibility .......................................................................
Appendix C: Remote Control Programming Codes ..........................................................................................
Appendix D: Cleaning and Service .....................................................................................................................
Appendix E: Diamond Shield Installation and Removal .............................................................................
Appendix F: Cabinet Separation Procedure .................................................................................................
Appendix G: Troubleshooting ........................................................................................................................
Index .................................................................................................................................................................
Mitsubishi Projection TV Limited Warranty .......................................................................................................
4-5
66
67
68
69
70-71
72-73
74-75
76-77
78
IMPORTANT
L Please
_Always
.
.
.
.
.
SAFEGUARDS
read the following
safeguards for your TV and retain for future
follow all warnings and instructions
marked on the television.
reference.
Read, Retain and Follow All Instructions
Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions
for future reference. Follow all operating and use instructions.
Heed Warnings
Adhere to all warnings on the appliance and in the operating instructions.
Cleaning
Unplug the TV from the wall outlet before cleaning. Do not use liquid, abrasive, or aerosol cleaners. Cleaners
can permanently damage the cabinet and screen. Use a lightly dampened cloth for cleaning.
Attachments
and Equipment
Never add any attachments and/or equipment without approval of the manufacturer as such additions may
result in the risk of fire, electric shock or other personal injury.
Water and Moisture
Do not use the TV where contact with or immersion in water is possible.
bowls, kitchen sinks, laundry tubs, swimming pools, etc.
Do not use near bath tubs, wash
6. Accessories
Do not place the TV on an unstable cart, stand, tripod, or table. The TV may fall, causing
serious injury to a child or adult and serious damage to the TV. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold with the TV. Any mounting
of the TV should follow the manufacturer's instructions, and should use mounting accessories
recommended by the manufacturer.
An appliance and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and cart combination to overturn.
7. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and
to protect it from overheating. Do not block these openings or allow them to be obstructed by placing the TV
on a bed, sofa, rug, or other similar surface. Nor should it be placed over a radiator or heat register. If the
TV is to be placed in a rack or bookcase, ensure that there is adequate ventilation and that the manufacturer's
instructions have been adhered to.
.
Power Source
This TV should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied to your home, consult your appliance dealer or local power company.
g.
Grounding or Polarization
This TV is equipped with a polarized alternating current line plug having one blade wider than the other. This
plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
10. Power-Cord
Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the TV.
11. Lightning
For added protection for this TV during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent
damage to the TV due to lightning and power-line surges.
IMPORTANT
12.
SAFEGUARDS
Continued
Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching such power lines or circuits as contact with
them might be fatal.
13. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
14. Object and Liquid Entry
Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or
short-out parts that could result in fire or electric shock. Never spill liquid of any kind on or into the TV.
15. Outdoor
Antenna Grounding
If an outside antenna or cable system is connected to the TV, be
sure the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static charges.
Section 810 of the National Electric Code, ANSI/NFPA No.
70-1984, provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead in wire to
an antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
ON,T
I
EQUIPMENT_
I-- / /_ J
_/.,_
CONDUCTORS
"_"_"_"
NEC
- NAT!ONAL
GROUNDING
ELECTRICAL
CODE
POWER
SERVICE
GROUNDING
ELECTRODE
SYSTEM
{NEC ART 250 PART H't
16. Servicing
Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
17. Damage Requiring Service
Unplug the TV from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
(a)
(b)
(c)
(d)
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the TV.
If the TV has been exposed to rain or water.
If the TV does not operate normally by following the operating instructions, adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the TV to its normal operation.
(e) If the TV has been dropped or the cabinet has been damaged.
(f) When the TV exhibits a distinct change in performance - this indicates a need for service.
18. Replacement
Parts
When replacement parts are required, be sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
19. Safety Check
Upon completion of any service or repair to the TV, ask the service technician to perform safety checks to
determine that the TV is in safe operating condition.
20.
Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
at Mitsubishi Would Like to Thank You
To the Mitsubishi
Consumer:
Welcome to the wonderful and exciting world of digital television! We are honored that you
chose Mitsubishi as your premier home entertainment
partner. The development
team at
Mitsubishi understands that our customers demand and expect the very best. Mitsubishi
is founded on the core beliefs and philosophies that drive us to deliver products that are
both cutting-edge
and upgradeable.
While some televisions are destined for near-future obsolescence,
Mitsubishi's
HD-upgradeable
televisions are engineered with "future-ability."
Your television
continue to provide unparalleled
home entertainment
for years!
will
Whether this is your first Mitsubishi consumer electronics product or an addition to your
growing Mitsubishi family, we hope that this television will bring you and your family many
hours of enjoyment.
THE PROMISE
We will engineer and manufacture the upgrades necessary so the HD-Upgradeable
television you purchased today can be made compatible with near-future advances in
digital television and digital interconnectivity.
Specifically, we promise that you will be able
to have your television upgraded, at a reasonable cost, to include an off-air HDTV tuner, a
cable TV tuner (for unscrambled
programming),
an IEEE 1394 (FireWire®) connection, HAVi
system control, and 5C copy protection.
Part I: Introduction
Unpacking Your New TV
Special Features
Please take a moment to review the following
list of items to ensure that you have received
Your new High Definition (HD) Upgradeable
bigscreen television has many special features
that make it the perfect addition to your home
entertainment system. A few of these special
features are described below.
everything included:
_11 Remote Control type []
[]
[]
or []
(2) AAA Batteries
(2) IR Emitter Cables
(WS-55411, WS-65411 and WS-73411 Only)
I_1 Product Registration Card
[] Owner's Guide
Quick Reference Card
HD Upgradeable
With the use of an optional HDTV receiver
(Mitsubishi SR-HD400 or similar model) your
Mitsubishi bigscreen can display high definition
pictures.
See pages 20 & 21 for more information.
16:9 Widescreen
TV
Enjoy a full theatrical experience in the comfort
of your home. View pictures as film directors
intended them. Both the DTV and DVD support
the widescreen format well-suited for your new
TV.
See pages 62-65 for more information.
4:3 Narrow Screen TV
Your Mitsubishi narrow screen displays
widescreen HD signal source(s) through the
letterbox format. The gray bars on top and
Or
_
MII"SI.IBISI-II
B
bottom make widescreen
viewing possible.
See pages 60 & 61 for more information.
Remote Control
Remote Control
(VS-50111,VS-60111,
WT-42311,WS-48311,
WS-55311, and WS-65311)
(WS-55411,
WS-73411)
(,_4AA
WS-65411, and
PIP/POP Viewing Option
Using Picture-in-Picture
and Picture-outsidePicture give you exciting options for viewing
favorite programs.
Batteries
See pages 58-59 for more information.
V-Chip Technology
_1
Mitsubishi understands you may want to
shield certain viewers from specific program
content. Your Mitsubishi bigscreen will allow
you to restrict programming
by general contents,
(2) IR Emitter Cables
(WS-55411,
WS-73411)
WS-65411 and
specific contents,
or even by time.
See pages 40-42 for more information.
_1 Product Registration
Card
Multibrand
Remote Control
Your Mitsubishi
remote control can be
programmed
to control many other audio/video
components.
See page 26 & 27 for more information.
l
Front Control Panel
Many remote control buttons are duplicated on the front control panel. These buttons are shaded
in Figure 1 and Figure 2. Please see Remote Control Functions, pages 54-58, for an explanation
of their usage.
S-VIDEO
VIDEO
L*AUDIO*R
A!V RESET
@
O
TIMER
INPUT*3
Figure 1. The ADJUST,
screen menus.
ENTER,
MENU, and CANCEL buttons
may be used to access
S-VIDEO
or navigate
VIDEO
through the
L*AUDIO*R
Figure 2. The ADJUST, ENTER, MENU, and CANCEL buttons may be used to access or navigate through the screen
menus (for models WT-42311 and WS-48311 only).
F
0
TIMER
Timer
During normal operation, the timer light glows green when the TV is On. It does not glow when the
TV is Off. When the time is used to turn On at a specific time, the green timer light blinks while the
TV is Off. See Timer Menu, pages 43-44 for timer setup instructions.
A!V RESET
@
CANCEL
A/V Reset
Press this button to reset the AiV memory on all eight inputs (seven inputs for the VS-50111 and
VS-60111) to the factory default settings. See Audio/Video
Settings Menu, page 48 for instructions.
S-ViDEO
_[__
VIDEO
°
@
L-AUDIO*R
__°
Input3
This input can be used for convenient
connection
of a camcorder
You may connect to the S-VIDEO or VIDEO terminal
or other video device to the TV.
but not to both.
Part I1: Installation
Back Panel
TV Rear Side
®®®
TV Back Panel
I'
?
i®
®
®
®m®
®
®
®
®
®®D®
@®®®
@®®®
®
®®®®®
®®®®®
®®®®®
®®
I
IR
EMITTER
Panel
REPEATER
H
_
1°1
n
Monitor Out
The Monitor Output sends the TV audio and video signals
(excluding
[]
component
video or DTV video) to an AiV receiver or other equipment.
Inputs 1-2
These inputs can be used for the connection
of a VCR, Super VHS (S-VHS) VCR, laser disc player,
or other AiV device to the TV. With each input, you may connect to the S-VIDEO or VIDEO
terminal
but not to both.
[] Antenna (ANT-A, LOOP OUT, and ANT-B)
ANT-A and ANT-B receive signals from VHFiUHF
the ANT-A signal out to another
Lq IR Emitter Repeater
Connecting
IR emitters
component,
antennas
or a cable system.
LOOP OUT sends
such as a cable box or VCR.
(System 4 Home Theater IR Control)
here allow the TV to automatically
home theater setup and pass IR commands
change a digital AiV receiver's
input in a
to other AiV devices.
(Applicable for WS-55411, WS-65411 and WS-73411 only.)
[]
DTV Input
This input is used to connect a DTV receiver and can be configured
(YPbPr),
RGB sync on green, and RGB plus H&V.
for HDTV component
Please see AppendixB,
page 67, for signal
compatibility.
r4 Component
Inputs 1-2
-rhese inputs can be used for the connection
as a DVD player or Video Game System.
(Models
VS-50111
and VS-60111
of AiV equipment
Please see Appendix
with component
video outputs,
such
B, page 67, for signal compatibility.
[4:3] only include Component
Input 1.)
How Connections
Affect the PIP and POP
To see a picture in the PIP or POP, you may
need to select an input source. If the only
input connected is ANT-A, then both the main
picture and the PIP/POP will be from that input
source. If other video equipment is connected,
you may be able to view these input sources
as the PIP/POP. When connecting your new
Mitsubishi bigscreen, it is important to
understand which main picture and PIP/POP
input sources can and cannot be used together.
Table 1 shows which inputs can and cannot be
used together and the limitations they may have.
If you press the INFO key it will display the
current Input, signal (480i, 480p, or 10800,
format, time, day and sleep time.
See Operation
of PIP and POP, pages 58-62,
for operating
instructions.
How Connections
OK*
NoPiP/POP
OK
OK
OK
OK
OK*
OK
OK
OK
OK
OK
OK**
OK
OK
OK
OK
OK
OK**
OK
OK
OK
OK
OK
OK**
Table 1. *No Side-by-Side with the same
channel.
**No Side-by Side with the same input.
Affect the System 4 Home Theater
IR Control
(Applicable for WS-55411, WS-65411 and WS-73411 only.)
The Mitsubishi System 4 Home Theater IR
Control is a special feature that makes it easier
to use your TV with a digital surround sound
AiV receiver. Once your equipment is properly
connected and set up, your TV and digital AiV
receiver will change inputs together to match
high resolution pictures with the proper
surround sound.
You will automatically hear the high quality
digital surround sound from digital products
like your DTV receiver and DVD player,
and high quality analog stereo or surround
sound from non-digital products like your
VCR.
When you change inputs on your TV to watch
different video products, your TV will send
signals via your remote control and the infrared
emitters to your digital AiV receiver to change
inputs.
remote will be passed through your TV to
your AiV devices. Your AiV devices can
be hidden or behind cabinet doors and
Additionally, all IR remote signals from your
Mitsubishi remote or other manufacturer's
controlled
by pointing the remote at the TV.
Part I1: Installation
Special Setups:
VCR:
Connect
A/V Equipment
(For System 4 Home Theater IR Control)
the cables to the TV as directed
on page 17, with one exception. Connect the
audio output connection to the appropriate input
on the back of the AiV receiver (as shown in
Table 1).
DVD: Connect the cables as
19 (using the COMPONENT-1
exception.
Connect the digital
connection on the DVD player
appropriate digital input on the
digital AiV receiver (as shown
directed on page
input), with one
audio output
to the
back of the
in Table 1).
DTV: Connect the cables as directed on pages
20-21, with one exception.
Connect the digital
audio output connection on the DTV receiver to
the appropriate digital input on the back of the
digital AiV receiver
(as shown
• Digital Input Assignment
for DVD: Assign
the digital input you used for your DVD player
to the AiV receiver's DVD input selector. This
procedure is explained in your AiV receiver's
Owner's Guide.
• Digital Assignment
for DTV: Assign the
digital input you used for DTV to the AiV
receiver's DTV input selector. This procedure
explained
in your AiV receiver's
Infrared
22.
Emitter:
Connect as shown on page
settings
in Table 1).
•TV Speakers:
OFF
,Audio Output:
Fixed
See Audio Video Menu, page 31.
•TV Inputs
Appropriately
See Input Assignment
•Auto Standby:
ON (See your AiV receiver's
Owner's Guide for this procedure).
For all TV
use, the sound will come from the AiV receiver.
Not available with all A/V receivers.
of various brands of AV Receivers
Named
Menu, page 31.
Remote Control,
pages 26-27.
,,Set the slide switch to the TV position and
follow the programming instructions using the
AiV receiver code appropriate for your AiV
receiver, page 27 (Figure 5).
are shown below.
The products listed at the top of this column connect to the
below listed inputs on the back of the appropriate AiV receiver.
Brand
Model
"l'V/Cable
Mitubishi
Mitsubishi
Denon
M-VR1000iMR800
M-RVR900iM-VRT00
AVR2800
JVC
Kenwood
RX-888V
VR-2080
Onkyo
Pioneer
TX-DS575
VSX-21
Sony
Yamaha
STR-DE825
RX-V2095
TV
TV
TViDBS
TV
AVAUX
VIDEO3
TVlSAT
TViDBS
TViDBS
Guide.
Special Setups: TV
To correctly setup System 4 use the following
A/V Receiver:
Connect as directed on page
18, with two additions.
Use an S-Video cable
in step 1 if you have an S-Video VCR. The
TV outputs should be connected to the AiV
receivers input marked TV.
Samples
Owner's
SAT/DBS/DTV
VCR2
CABLEiDBS
VCR2
VIDEO2
LD
VIDEO2
VIDEO2
VIDEO2
VCR2
Table 1. A/V receiver back panel input table (Connections
VCR
VCR1
VCR
VCR1
VCR1
VIDEO1
VIDEO1
VCR1
VIDEO1
VCR1
is
DVD
DVD
DVD
DVDiLD
DVD
DVD
DVD
DVDiLD
DVDiLD
DVDiLD
vary by model; you may need to test individually)
Connecting an Antenna, Wall Outlet Cable, or Cable Box
VHF
A_tenna
(Chennels
UHF_te_r_
(£';h_nnels 14-_9)
213)
TV back panel
I
Separate
View)
I
ANT-A
Pl_t r
FI_ ]'_4n Leaf
(Detailed
'
Extem_
Antetltl_
or C_b_e
UHF and VHF Antennas
(Figure 1)
_11 Connect the UHF and VHF antenna
to the UHFiVHF combiner.
[]
Push the combiner
[]
back panel.
UHF/VHF
combiners
leads
onto ANT-A on the TV
are not provided
with the TV. They are available
electronic
stores.
Figure 1. Connecting separate UHF and VHF antennas.
Note: See page 5 for Outdoor Antenna Grounding
at most
TV back panel
Twin Lead Antenna, Coaxial Lead
Antenna, or Wall Outlet Cable
[]
View
I
For antenna with twin flat leads (Figure 2)
_11 Connect the 300ohm
transformer.
(Detailed
,,
300 Oh#_Fret
T_r_ Le_d
75 Ohm
Co_al C_bIe
I
twin leads to the
I
I
Push the 75ohm side of the transformer
onto ANT-A on the TV back panel.
Opt!£1tal _
300ohm to 75ohm matching transformers
are not provided with the TV. They are
available at most electronic stores.
For cable or antenna with coaxial lead (Figure 2)
[]
Connect the incoming
the TV back panel.
cable to ANT-A
on
Ohm
to 75 Ohm
Figure 2. Connecting twin lead antenna, coaxial lead
antenna, or wall outlet cable.
Note: See page 5 for Outdoor Antenna Grounding
ncoming
Cable
,. ....
_lm--_ob
;_r
......
®
@
TV beck panel (Detailed
View)
LOOP
IANT'A
OUT
ANT-B
Cable Box
(Figure 3)
_11 Connect the incoming
[]
[]
cable to ANT-A on
the TV back panel.
Connect two coaxial cables as follows:
One from LOOP-OUT on the TV back panel
to IN on the cable box back panel.
One from OUT on the cable box back panel
to ANT-B on the TV back panel.
Figure 3. Connecting the cable box.
Note: See page 5 for Outdoor Antenna Grounding
|MPGRTANT
Part I1: Installation
Antennas or Wall Outlet Cable
Connecting a VCR
(Figure 1)
H
Connect the incoming cable to ANT-A on
the TV back panel.
E_J Connect two coaxial cables as follows:
One from LOOP-OUT on the TV back panel
to ANTENNA IN on the VCR back panel.
One from VCR back panel ANTENNA OUT
to ANT-B on the TV back panel.
IL_ Now complete Figure 3, steps 1-2.
Figure 1. Connecting VCR with antennas or wall outlet
table.
Cable Box
(Figure 2)
H
Connect the incoming
cable to ANT-A on
the TV back panel.
E_J Connect three coaxial cables as follows:
One from LOOP-OUT on the TV back panel
to IN on the back of the cable box.
One from OUT on the back of the cable
box to ANTENNA IN on the VCR back
panel.
Figure 2. Connecting
IL_ One from ANTENNA OUT on the VCR back
panel to ANT-B on the TV back panel.
Now complete Figure 3, steps 1-2.
VCR with cable box.
TV back
panel
(Detailed
View)
Composite Video with Audio or
S-Video with Audio
(Figure 3)
H
L................
VCR
_
back#_[nel
If your
chan_lel
VCR
has
or RF
Connect a video cable from VIDEO OUT on
the VCR back panel to VIDEO INPUT-1 or
INPUT-2 on the TV back panel.
If you have an S-VHS VCR, follow the
same steps using the S-Video terminals
the VCR and TV (in place of the composite
terminals). You may connect to the
S-VIDEO or VIDEO terminal but not to
_ video
ON!OFF
switch, se_ to OF_
OUT
•
•
•
Figure 3. Connecting the VCR Audio/Video.
both.
Connect
a set of audio cables from AUDIO
OUT on the VCR back panel to AUDIO
INPUT-1 or INPUT-2 on the TV back panel.
The red cable connects to the R (right)
channel and the white cable connects to
the L (left) channel. If your VCR is mono
(non-stereo), connect only the white (left)
cable.
Connecting an Audio Receiver
TV back panel
(Detailed
....
I
m
i
i
' I
m
I
I
I
I
I
Stereo Audio System
(Figure 1)
_11 Connect the audio cables from AUDIO
MONITOR OUTPUT on the TV back panel
to TV IN or AUX IN terminals on the back of
/
the audio system. The red cable connects
to the R (right) channel, and the white cable
connects to the L (left) channel.
[]
[]
Turn off the TV's speakers
through
C
the AiV
SETTINGS Menu, page 48.
Set the audio system's input to the TV
or AUX position to hear the TV's audio
through your stereo system.
_
Audio
svstem
back p_nel section
._ ÷
®
®
Figure 1. Connecting the Stereo Audio System.
|MPGRTANT
i t,I I_aCK
_llef[U_l
I{[_l
view}
I@@
omoo
A/V Receiver
(Figure 2)
@
®
®®
®®
_11 Connect either a video cable or an
S-Video cable (but not both) from VIDEO
MONITOR OUT on the back of the AiV
receiver to VIDEO INPUT-1 or INPUT-2 on
[]
the TV back panel.
Connect a video cable from VIDEO
MONITOR OUTPUT on the TV back panel
to VIDEO TV IN on the back of the AiV
receiver.
[]
Connect a set of audio cables from AUDIO
MONITOR OUTPUT on the TV back panel
to AUDIO TV IN on the back of the AiV
receiver. The red cable connects to the
R (right) channel, and the white cable
connects to the L (left) channel.
Figure 2. Connecting the A/V Receiver.
|MPGRTANIT
View)
Part I1: Installation
WARNING:
DVD Player with Component
Video
(Figure 1)
[]
Connecting a DVD Player
TV back panel
(Detailed
Connect the Component Video cables from
(YCb Cr or Y Pb Pr) VIDEO OUT on the
back of the DVD player to COMPONENT-1
or COMPONENT-2
on the TV back panel,
View)
matching
Ill
[]
[]
the correct components:
YtoY
CborPbtoPb
CrorPrtoPr
Connect
a set of audio cables from AUDIO
OUT on the back of the DVD player to
COMPONENT AUDIO Input 1 or 2 on
the TV back panel. The white cable L_!
connects to the L (left)channel,
and the
red cable D connects
channel.
to the R (right)
|MPQRTANT
Figure 1. Connecting a DVD Player with Component
Video.
Connecting an S-Video
Device
TV back
panel
(Detailed
View)
Other S-Video Device
(Figure 2)
I
@@
®®
@@_-_
il
Re_
I
an S-Video
cable from VIDEO OUT
on the device back panel to VIDEO INPUT-1
or INPUT-2 on the TV back panel.
[]
00
Connect
Connect
a set of audio cables from AUDIO
OUT on
INPUT-1
,,The red
channel
the device back panel to AUDIO
or INPUT-2 on the TV back panel.
cable connects to the R (right)
and the white cable connects to
the L (left) channel.
,,If your S-Video Device is mono (nonstereo), connect only the white (left) cable.
Figure 2. Connecting S-Video Device.
g a DTV Recewer
DTV Connectors
and Adaptors
(Figure 1)
The TV back panel has five RCA-type
connectors for the DTV connection.
The back
panel of your DTV receiver may use RCA-type
connectors or BNC-type connectors.
If your
DTV receiver comes with BNC type
connections, you will need to purchase BNC to
RCA adaptors to connect the TV to the DTV
receiver. These adaptors should be available at
most electronic supply stores.
or
BNC to
RCA
Adaptor
BNC
Connector
A_
Fitted to
Connection
RCA
Connector
Figure 1. DTV connectors and adaptors.
TV back panel (Detailed View)
DTV Receiver with Component
Video Connections
m
@
(Figure 2)
@
@
_11 Connect the outside antenna cable, or
satellite to ANT or SATELLITE IN on the
@@ @
i®®
i!1®®
®®l®
®@
DTV receiver (see your DTV receiver
owner's guide for instructions and cable
compatibility).
®®
@
@® @
ANT-A
[]
Connect
or cable
TV back
at most
the incoming terrestrial
(not satellite) to ANT-A
panel (a coaxial splitter,
electronic supply stores,
required to complete
[]
@
this installation).
You may need to set the DTV Input
Assignment,
page 31, to YiPbiPr.
Connect the L (left) and R (right) audio
cables from the DTV receiver to DTV
AUDIO on the TV back panel.
[]
ANTRA
Connect the RCA-type cables from the
outputs on the DTV receiver to DTV INPUT
YiPbiPr or Satellite/Box
on the TV back
panel.
D
antenna
on the
available
may be
To utilize the benefits of a digital
AiV receiver, connect your DTV receiver's
digital audio out to a digital input on your
digital AiV receiver. Component 1 and 2
may also be used for 1080i component.
Figure 2. Connecting the DTV receiver with component
Video Connections.
IMPORTANT
Part I1: Installation
Connecting a DTV Receiver
DTV Receiver with RGB Video
Connections
(Figure 1)
H
Connect the outside antenna, cable, or
satellite to ANT or SATELLITE IN on the
DTV receiver (see your DTV receiver's
owner's guide for instructions and cable
compatibility).
®
[]
®®
[]
ANTRA
_@
Figure 1. Connecting the DTV receiver with RGB video
connections.
Connect the incoming terrestrial antenna
or cable (not satellite) to ANT-A on the
TV back panel (a coaxial splitter, available
at most electronic supply stores, may be
required to complete this installation).
Connect the RGB cables from the DTV
receiver to the TV back panel as listed
below (if your DTV receiver uses BNC-type
cables, use the adaptors shown in
Figure 1, page 20):
DTV ReceiverTV
|MPQRTANT
[]
D
G (green)
B (blue)
[]
R (red)
Back Panel
=
=
Y
Pb
=
Pr
=8 If the
DTV receiver has outputs for H
and V sync, connect as listed below (DO
NOT connect if DTV receiver uses "Sync
on Green"):
H (horizontal sync)
kl V (vertical sync)
D
=
=
H
V
Connect the L (left) and R (right) audio
cables from the DTV receiver and to DTV
AUDIO on the TV back panel.
To utilize the benefits of a digital
AiV receiver, connect your DTV receiver's
digital audio out to a digital input on your
digital AiV receiver.
You may need to setup the DTV (See Input
Assignment, page 31) to RGB.
Connecting
(Applicable
the System 4 Home Theater IR Control
for WS-55411,
WS-65411
and WS-73411
models
only)
(Figure 1)
Connecting the System 4 Home
Theater IR Control.
_11 Connect the IR emitter to IR EMITTER
REPEATER
[]
[]
Place the IR emitter cable under or
along the side of the AiV device. Place
the IR lens directly in front of the AiV
device infrared signal receiver. Infrared
signal receivers are usually behind the front
translucent panel of the receiver.
Place the unused transmitter
the-way
D
on the TV back panel.
in an out-of-
location.
For permanent installation of the IR emitter
cable, use the included adhesive tape to
secure the bottom of the emitter to the
anchoring
object of your choice.
I_
[]
I
Other AN
Device
I
AN
Receiver
,j
Figure 1. Connecting the System 4 Home Theater IR
Control.
Part I1: Installation
Warning:
Do not leave stationary or letterbox images on the screen for
extended periods of time. Mix the types of pictures shown.
Uneven picture tube aging is NOT covered by your warranty.
The normal use of a TV should include
a mixture of TV picture types. The most
frequently used picture types should fill
the screen with constantly moving images
rather than stationary images or patterns.
Displaying the same stationary patterns over
extended period of time or displaying the
same stationary pattern frequently can leave
subtle but permanent ghost images. To avoid
this, mix your viewing pattern. Do not show
the same stationary image for more than 15%
of your total TV viewing in any given week.
Display constantly moving and changing
images that fill the screen whenever possible.
This projection TV uses picture tubes to
project the image to the screen. All picture
tubes age with use. As they age, their light
output is gradually reduced.
Normal TV
pictures fill the screen with constantly
changing images. Under these conditions,
picture tubes age at an even rate across the
entire screen. This maintains a TV picture
that is evenly bright over the whole screen.
Stationary images or images that only partially
fill the screen (leaving black or colored bars
to fill the screen), when used over extended
periods of time or when viewed repeatedly,
can cause uneven aging of the phosphors and
leave subtle ghosts from the stationary images
in the picture.
Still or stationary images may be received
from broadcasters, cable channels, satellite
channels, DVD discs, video tapes, laser
discs, online services, webilnternet
searching
devices, video games, and digital TV
tuner/converter
boxes. Examples of these
types of images can be, but are not limited to
the following:
[]
Letterbox top/bottom
black bars:
shown at the top and bottom of the TV
screen when you watch a widescreen
(16:9) movie on a standard
(4:3) TV.
Side bar images: solid bars shown on
each side of an image when watching a
standard (4:3) program on a widescreen
(16:9) TV.
Stock-market
report bars: ticker running
at the bottom of the TV screen.
Shopping channel Iogos & pricing displays:
bright graphics that are shown constantly or
repeatedly in the same location.
Video game patterns and scoreboards
Bright station Iogos: moving or low-contrast
graphics are less likely to cause uneven aging
of the picture tubes.
Online (Internet) websites: or any other
stationary or repetitive computer style images.
Closed Captioning
: Use of the Remote Control with Other A/V Products
_To Program the Remote to Control
Other Brands of Audio and Video
Products(Figures 1-5)
_11 Move the slide switch at the top of the
remote to the product you want to control.
[]
Press and hold the POWER
remote control.
[]
Enter the first three digit code listed for your
equipment, and then release the POWER
button on the remote control.
[]
button on the
Point the remote control to the equipment
and press the POWER button.
Note: If the equipment responds, the remote
control is properly programmed to operate
the equipment.
If the equipment does not
respond, repeat steps 2-4 with the next
three digit code listed in step 3 for your
equipment.
POWER
D
m
TV
Satellite brand
Mitsubishi DTV- DBS
DishnetworkiEchostar
Codeto enter:
006
175
If your
satellite
receiver
Hughes - DBS
RCA- DBS
173
176
Sony - DBS
Toshiba - DBS
177
170
code is not
listed here,
please see
page 68
for a
Panasonic - DBS
TO reset to default
174
code,
enter
000
Figure 2. Programming the remote to control your
satellite receiver.
POWER
El
£
POWER
TV
[_,3FJ_FJ:_I
Cable box brand
General Instruments/
Jerrold
Oak
Pioneer
Scientific Atlanta
Zenith
Codetoen_r:
111,119,120,121,122,
123,124,125,126,127
102,137,139
101,116
111,112,113
100,117
To reset to default code, enter 000
If your
cable box
code is not
listed here,
please see
page 68
for a
complete
listing.
Figure 1. Programming the remote to control your cable
box.
complete
listing.
D
m
TV
_1_][_
VCR brand
C0det0en_r:
Mitsubishi
Hitachi
JVC
001,002
020,043,065
030,054,059
043,044,051
041,042,043
020,053,065,079
048,049,050,074,075
021,
Phillips / Magnavox
Panasonic
RCA
Sony
Toshiba
If your
VCR
code is not
listed here,
please see
page 68
for a
complete
listing.
To reset to default code, enter 000
Figure 3. Programming the remote to control your VCR.
iMPORTANT
|MPQRTANT
Part II1: Setup
Use of the Remote Control with Other A/V Products
POWER
D
TV
AUDIO
DVD/LDP brand
Codetoenter:
if you r
Mitsubishi (DVD)
Mitsubishi (LDP)
Panasonic
Pioneer DVD (LDP)
003
016, 017
250
252 (016, 017)
DVD
code is not
listed here,
please see
page 68
for a
complete
listing.
Sony
Toshiba
Zenith
TO reset
254
253
259
to default
code,
enter
000
After entering the correct codes in each
position of the remote control, use the slide
switch to select which product will respond
when an operational button is pressed. If you
enter a code from the AUDIO chart while the
slide switch is set to TV, the volume and mute
functions change to match the AiV receiver.
This is useful when using an AiV receiver with
the TV all the time. In all other cases, only
one of the below devices is allowed for each
slide switch position.
Figure 4. Programming the remote to control your DVD/
LDP.
TV position:
[] TV
POWER
TV
and/orCD player
Kenwood
Onkyo
Pioneer
Sony
Yamaha
Harman
Teac
010, 011
200, 208
209, 214,240
205, 207
222
201,202
215
210
_ your
audio
code is not
listed here,
please see
page 68
for a
complete
listing
To resetto defaultcode,enter 000
Figure 5. Programming
receiver.
the remote to control your A/V
| PQRTANT
and mute only)
CableiDBSiDTV
position:
EmJCable box
E_J Satellite receiver
E_J DTV receiver
il
£
Audio brand
Codetoenter:
MitsubishiAN receiver
AiV receiver (volume
VCR position"
VCR
DVD position"
E_J DVD
E_J LD Player
Audio
AiV
position:
receiver
Mitsubishi
CD player
If you have a Mitsubishi
AiV receiver,
the
audio position may be used in conjunction
with select Mitsubishi CD players.
Your audio
position must be programmed
to either 010
or 011. Plug the CD player power cord into
a switched outlet on the back of your AiV
receiver. Pressing the POWER button turns
On the AiV receiver, along with the CD player.
In the audio position, for some CD players,
the transport controls (FF, Play, Rew, etc.)
|MPQRTANT
operate
the CD player.
The I !BWPOiMenu System
_Your
TV has Mitsubishi's
on-screen
on-screen
changes
exclusive
I_
®
operating system, which provides
information for menu choices and
(Figure
1).
A picture (icon) will be highlighted
when selected with the ADJUST
arrows.
When selected,
the
appropiate menu will appear or start
an automatic function.
You may then
make changes within the menu or
access available sub-menus.
A square button indicates that you
may make changes to the menu
screen.
The I_
®system
Figure 1. MAIN menu:
The first screen that appears when you press the
MENU button from your remote.
includes the following
special features:
• qJThe currently selected icon or button
is highlighted with a rectangular yellow
outline and the text color will be yellow.
• qJOn-screen instructions provide complete
menu choice information.
• qJSome on-screen menu options must be
set before other options are available.
For example, "Timer Menu"will only be
possible if "Clock Time"and "Set Day"
have been set.
The following buttons on your remote control
helps you to navigate within the I_MJlI[ ®system
(Figure 2):
_11 ADJUST A or v to select the menu item
you want to change.
[] ADJUST I_ to move to the setting field.
[] ADJUST A or v to change the settings.
L_I ADJUST < to move back to the menu item.
[] ENTER to enter into a menu, start an
automatic function, or select a checkbox.
11'41
CANCEL to clear a setting, or stop an
automatic function.
kl
F_EC
REWiREV
STOP
PLAY
PAUSE
Q
FF/FWD
,,_ MITSUBISHI
MENU to move back one menu screen at
a time.
IL_ HOME to exit all menus and return to TV
viewing.
Figure 2. These buttons are used for navigation within
the _B_IE ° on-screen operating system.
Part II1: Setup
Main Menu Screens (Overview)
SETUP Menu
(Figure 1)
Basic (initial) setup instructions and functions
are available through the SETUP submenu
screens. You can memorize channels, turn
the TV input connections On or Off, set the
time and day, select English or Spanish for the
menus or screen display, and set the Front
Button Lock. (Use the setup menu when you
relocate the TV, experience a power loss or
when accessories are added after initial setup).
Figure 1. SETUP menu
CAPTIONS
Menu
(Figure 2)
Display broadcasted captions or text on the
screen. You can select the closed caption
setting by choosing to display the
background color as either black or
translucent gray.
Note: Mitsubishi recommends using the
translucent gray background to prevent CRT
aging and/or burn-in.
Figure 2. CAPTIONS menu
CHANNEL
EDIT Menu
(Figure 3)
Use to customize
the channel information
for
Ant-A and Ant-B. Manually add or delete
channels from memory, name channels for
Ant-A and Ant-B, or add your favorite channels
to a SQV (Super Quick View TM) list.
Figure 3. CHANNEL EDIT menu (ANTENNA)
Main Menu Screens (Overview)
V-CHIP LOCK Menu
(Figure 1)
The V-Chip Lock locks the entire TV based on
a scheduled set time, or blocks programs based
on rating signals sent by broadcasting system.
Figure 1. V-CHIP LOCK menu
ADVANCED
FEATURES
Menu
(Figure 2)
Set your TV to turn On automatically,
converge (align) the three main colors,
display a blue screen when viewing an input
with no signal, enhance the darker parts of
bright pictures, and adjust the color balance.
Figure 2. ADVANCED FEATURES menu
AUDIO/VIDEO
SETTINGS
Menu
(Figure 3)
Adjust some or all of the AiV settings. Each
input can be set to your preferences.
AiV Reset
on the menu allows you to return the AiV
settings for the current input to the factory
presets. AiV Reset on the front button resets all
inputs at one time.
Figure 3. AUDIO!VIDEO
SETTINGS menu
Part II1: Setup
SETUP Menu: Memorize Channels/INPUT
Memorize
ASSIGNMENT
Channels
(Figure 1)
This selection memorizes the channels your TV
can receive and skips the unused or weak
channels.
|MPQRTANT
Figure 1. Memorize Channels
MEMORIZE
Menu
(Figure 2)
You can stop memorization at any time by
pressing CANCEL.
Channels memorized prior
to pressing CANCEL will stay in memory.
After channels are memorized, you may select
memorized channels in ascending or
descending order by pressing the CHANNEL
button on the remote control.
Now memorizing
all the stations
you can receive
on Ant-A Air.
Please
standby.
Figure 2. MEMORIZE menu (Memorize Channels
in memory)
INPUT ASSIGNMENT
Menu
(Figure 3)
INPUT ASSIGNMENT
turns off unused inputs,
turns them on again, or changes the name of
the input. If you turn an input Off, it will be
skipped when you press the INPUT button on
the remote control.
[]
Antenna-A
Input choices
or Antenna-B:
are:
On or Off.
LmJ DTV: YPbPr, RGB, or Off.
INPUT-l, INPUT-2, INPUT-3:
Cycle through a list of preset names, or
Off.
COMPONENT-1
or COMPONENT-2:
Cycle through a list of preset names, or Off.
Figure 3. INPUT ASSIGNMENT
menu
SETUP Menu: Language /Front Button Lock
_Language
(Figure 1)
Display the on-screen menus in either English
or Spanish (EspaSol). The first time your power
On your TV, you were requested to select an
on-screen menu language. When you change
the selection to EspaSol, all text will immediately
switch to Spanish.
Figure 1. Language/Idioma
Front Button Lock
(Figure 2)
Front Button Lock lets you disable controls on
the front panel to prevent young children from
changing settings by accident.
Select On to lock out the operations of the
front panel button and select Off to restore the
operations of the front panel buttons. If the
front panel buttons have been locked and you
misplace the remote control, you can restore the
function of the front panel buttons by pressing
and holding the MENU button on the front panel
for more than 8 seconds.
If the TV is already
on, a message will be displayed to confirm the
release of the Front Button Lock.
Figure 2. Front Button Lock
Part II1: Setup
CLOCK Menu: Clock Setting / Tme Zone / D.S.T.
Clock Setting (Auto)
(Figure 1)
Setting the Clock Setting to Auto will
automatically set the day and time using
Extended Data Service (XDS) time data. This
data is automatically retrieved when tuned to
a PBS channel or other channels carrying this
service.
Figure 1. Clock Setting (Auto)
Time Zone
(Figure 2)
When Auto has been selected
for the Clock
Setting, you need to select the correct time zone
(Atlantic, Eastern, Central, Mountain, Pacific,
Alaska,
or Hawaii) for your area.
Figure 2. Time Zone
Daylight Savings Time
(Figure 3)
When Auto has been selected
for the Clock
Setting, you need to select the Daylight Savings
Time (DST) option that your state uses.
Applies = uses DST
Ignore = does not use DST
Figure 3. Daylight Savings Time
The clock time and day will be set automatically
after tuning to a channel carrying the Extended
Data Service (XDS) time data (usually your
local PBS channel).
Clock Time / Set Day
Clock Menu:
Clock Time
(Figure 1)
For the manual clock setting, select the current
time, including AM or PM.
Press A or • to slowly adjust the time. Press
and hold A or • to quickly adjust the time.
Figure 1. Clock Time
Set Day
(Figure 2)
When Manual
has been selected for the Clock
Setting, you need to select the current day of
the week.
Figure 2. Set Day
Part II1: Setup
CAPTIONS Menu: Closed Captions
CAPTIONS
Menu
(Figure 1)
Broadcasters
can send either Standard
or Text
closed captioning.
Standard closed captioning
follows the dialogue of the characters on-screen
and displays in a small section of the screen.
Text closed captioning often contains
information such as weather or news and covers
a large portion of the on-screen program. Your
TV can decode four different standard and four
Figure 1. CAPTIONS menu
different text closed captioning signals from
each TV station. However, each TV station may
broadcast only one or two closed captioning
signals, or none at all.
Within the CAPTIONS menu, you can turn On
or Off the closed caption decoder, select the
type of captions or text, and choose black or
translucent gray as the background color for the
closed caption area.
| PGRTANT
Closed Captions
(Figure 2)
The TV can display one of the following:
LmJCC1, CC2, CC3, or CC4: Standard
[]
Figure 2. Closed Captions
closed
captioning signals.
Text1, Text2, Text3, or Text4: Text closed
captioning signals.
On if mute: Closed captions when
mute. When selected, the standard closed
captioning signal (CC1) will turn on/off by
pressing the MUTE button on the TV
remote control.
Off: No closed captions.
f_CAPTIONS
_CC
Menu: CO Background
Background
(Figure 1)
To make the closed captions easier to read, you
can choose to display the background color as
either black or translucent gray.
Note: Mitsubishi recommends using the
translucent gray background to prevent CRT
aging and/or burn-in.
Figure 1. CAPTIONS menu
|MPGRTANT
Part II1: Setup
CHANNEL EDIT Menu: Antenna and Channel
Antenna
(Figure 1)
Select Ant-A or Ant-B.
For each antenna,
you can add or delete channels in memory,
name channels, and add channels to the
SQV (Super Quick View TM) list.
Figure 1. Antenna
Channel
(Figure 2)
Select the channel you want to add or delete
from memory, name, or add to the SQV
(Super Quick View TM) list.
Figure 2. Channel
CHANNEL EDIT Menu: Memory and Name
Memory
(Figure 1)
After all available
channels
have been
memorized with Memorize Channels (page 31),
weaker channels viewed with Ant-A or Ant-B
can be added and unwanted channels can be
deleted.
Use the CHANNEL button on the remote control
to view memorized channels.
Figure 1. Memory
Name
(Figure 2)
Channels shown on Ant-A or Ant-B can be given
names (up to four characters).
After you enter
a name, it will appear on the TV screen next to
the channel number.
0
Select Ant-A or Ant-B.
Select the memorized
name.
channel you want to
m Press
D
ADJUST
until you see the
underline
highlighted
in the Name
field.
Use ADJUST • or v to select letters A-Z,
numbers 0-9, and/or symbols (!.&'i:*- and
blank) for each character of the name you
would like for the selected channel. Press
ENTER
after choosing
each
letter and
after the name is complete. If you want to
change your selection while on the option
field, use CANCEL to delete the current
character. You will move one position back.
If you press CANCEL while at the first
character, the entire name will be deleted.
Figure 2. Name
Part II1: Setup
CHANNEL EDIT Menu: SQV (Super Quick View TM)
SQV (Super Quick View
Using
The Remote
TM)
Control
Changing SQV banks using the remote
control:
0
[]
H
Screen
[]
(Figure 1)
SQV (Super Quick View TM) allows you to put
together a list of your favorite channels from
Ant-A and Ant-B. You can store up to 6
channels in each of the 9 different memory
banks. Once you have added a channel to
the SQV memory, "SQV" will appear under the
channel number on the TV screen.
Use the CHANNEL
or number
buttons to
Press and hold the SQV button for about
3 seconds. When "SQV" and the memory
bank number appear under the channel
number, the channel has successfully been
added.
Removing
control:
SQV channels
using the remote
_11 Press the SQV button repeatedly
see the desired channel.
Changing
SQV channels
the menu:
g
and banks using
[]
control to select the channel you wish to
add or delete from a SQV memory bank.
Press • when at SQV in the menu to move
the selector to the On/Off choice.
[]
Press
• or v when at SQV in the menu
to select the SQV memory
to modify.
D
bank you wish
Press ENTER to add (On) or delete (Off)
the current channel from the SQV memory
bank that you have selected.
While the channel
until you
number and SQV
indicator are still displayed on the screen,
press the CANCEL button. If the CANCEL
button is not pressed before the SQV
indicator disappears, the channel will not be
removed.
Press =, or v when at Channel in the menu
or use the CHANNEL button on the remote
[]
using the
select the channel you want to add to the
current SQV memory bank.
SQV (Super Quick View TM)
The Menu
To change memory banks, press a number
button within 5 seconds of pressing the
SQV button.
Viewing and Adding SQV channels
remote control:
Figure 1. SQV (Super Quick View TM)
Using
Press the SQV button.
[]
When the SQV indicator disappears, the
channel has successfully
been removed.
V-CHIP Menu: V-CHIP LOCK
_Entry to the V-CHIP
LOCK
(Figures 1-2)
The first time you select V-CHIP LOCK from the
MAIN menu or after you have canceled your
passcode, you will see the screen shown in
Figure 1. Use the number buttons on the
remote control to input a new four-digit
passcode, then press ENTER. You can
delete a character and move back one
character by pressing CANCEL, or leave
the passcode screen by pressing MENU or
HOME. The next time you select V-CHIP
LOCK from the MAIN menu, input your
passcode as shown in Figure 2 (Note: Text
changes from "a new" to "your" passcode.)
Figure 1. First time entry to the V-CHIP LOCK
V-CHIP LOCK
(Figure 3)
Figure 2. Re-entry
to the V-CHIP LOCK
You can Block or Allow programs based upon
rating signals sent by the broadcasting station.
The factory preset for TV Ratings is TV-PG
(Parental Guidance) allowing only programs
rated TV-PG or lower. The factory preset
for Movies is PG, allowing only movies rated
PG or lower.
|MPORTANiT
Figure 3. V-CHIP LOCK menu
Part II1: Setup
V-CHIP LOCK Menu: V-Chip (continuation)
V-Chip Signal Information
When provided by the broadcaster, V-Chip ratings can be used to control which programs can be viewed or will be
blocked. When V-Chip ratings are sent, you will see the ratings when you change the channel or when you press
the INFO button on the remote control. The V-Chip rating includes both TV and Movie ratings. TV ratings apply to
programs and movies developed for TV. TV ratings can have supplemental blocking by content categories. Movie
ratings use MPAA ratings for movies released in theaters.
TV Ratings:
Used with TV programs and made for TV movies.
TV-Y
Youth, designed for children under the age of 7.
TV-Y7
Youth, 7 years old and older. Designed for children 7 years old and older.
TV-G
General Audience. Designed for the entire family to view.
TV-PG
Parental Guidence. Parental Guidence is recommended, may not be suitable for some children.
TV-14
Adolescent 14 years old and older. Not recommended for children under the age of 14.
TV-MA
Mature Audience. Recommend for adults only.
Content Categories:
Used in association with the TV ratings above.
FV
Fantasy Violence- applies to TV-Y7 only.
D
Sexual Dialog- applies in different degrees to TV-PG and TV-14.
L
Adult Language- applies in different degrees to TV-PG, TV-14, and TV-MA.
S
Sexual Situations- applies in different degrees to TV-PG, TV-14, and TV-MA.
V
Violence (graphic or realistic)- applies in different degrees to TV-PG, TV-14, and TV-MA.
TV
Rating
FV
D
L
S
V
TM-PG
x
x
x
x
TM-14
x
x
x
x
x
x
x
TV-Y
TM-Y7
TM-MA
x
Movie Ratings:
Used with theater released movies and direct-to-video movies.
G
General Audience- Designed for the entire family to view.
PG
Parental Guidence- Parental Guidence is recommended, may not be suitable for some children.
PG-13 Parental Guidence 13 years old and older- Not recommended for children under the age of 13.
R
Restricted- Restricted in the theater to 17 years old and older unless accompanied by an adult.
N0-17 No Children- Restricted in the theater to 18 years old and older.
X
Adult- Designed for and restricted in the theater to adult audiences only.
Programs Not Rated: Used for programs that are not rated like news, sports, weather, emergency bulletins, or
movies such as those prior to or without MPAA Ratings. This does not include programs without V-Chip signals.
When you select a TV or Movie rating, you are selecting the highest level of program that will be allowed to be
viewed. As an example, if you select TV-PG, you are allowing programs rated TV-Y, TV-Y7, TV-G and TV-PG to
be seen and blocking programs rated TV-14 and TV-MA. If you select a movie rating of PC-13, you are allowing
movies rated G, PG and PC-13 to be seen and blocking movies rated R, NC-17, and X. When you select a TV
Content category, you will block all TV programs that have the same content category listing. As an example,
if you select to block V (Violence) at the TV-14 level, you will also block any program that has the V category
listing at the TV-PG rating level as well.
V-CHIP LOCK Menu: V-Chip Hours/Lock
by Time
_V-CHIP HOURS / LOCK BY TIME
(Figure 1)
V-CHIP HOURS/LOCK
BY TIME will allow you
to activate the V-Chip or lock the entire TV
during specific hours.
V-CHIP Start Time and V-CHIP Stop
Time
(Figure 2)
Select the times you would like the V-Chip to be
Active. By setting the V-Chip Start Time and
V-Chip Stop Time to the same time, the V-Chip
will be active 24 hours a day.
Press A or • to slowly adjust the time.
Press
Figure 1. V-CHIP HOURS/LOCK
BY TIME
and hold A or • to quickly adjust the time.
Lock by Time, Lock Time, and
Unlock Time
(Figure 2)
Lock by Time locks the entire TV when Lock by
Time is On. Your TV continues to be locked
until you input your passcode,
locked time expires.
or when the
Passcode Screen
Figure 2. V-CHIP HOURS/LOCK
(Figure 3)
To view a program blocked by V-Chip or
watch the TV blocked by Lock by Time,
you must enter your four-digit passcode.
The figure to the right shows the passcode
request when Lock by Time has blocked the
TV. A similar passcode request is displayed
when V-Chip has blocked a program. A
released block will not block again until the
TV is turned off. When the TV is turned on
again, if the block still applies, the passcode
is requested again.
Figure 3. Passcode
Screen
BY TIME
Part II1: Setup
ADVANCED FEATURES Menu: TIMER, Timer Menu, and Set Time
TIMER
(Figure 1)
The timer will automatically
turn the TV on (if
it is off) at the time you schedule and select.
When Ant-A or Ant-B is the selected input, you
may select any memorized channel. The TV
will tune to this channel when the timer turns
it on.
|MPGRTANT
Figure 1. ADVANCED FEATURES menu (Timer)
TIMER menu
(Figure 2)
The timer can be turned On or Off. When On,
you need to select the time and the day to turn
On and the input and channel to display. At
your preselected time, the timer will turn the
TV on and a message will be displayed, "Press
a key for the TV to stay on." Any button on
the remote control must be pressed within 5
minutes or the TV will turn itself off.
Figure 2. TIMER menu (Timer)
Set Time
(Figure 3)
Select the hour and minute, including
when the TV is to turn on.
AM or PM,
Press • or v to slowly adjust the time. Press
and hold • or v to quickly adjust the time.
Figure 3. TIMER menu (Set Time)
ADVANCED FEATURES Menu: Set Day, Input, and Channel
Set Day
(Figure 1)
Select the days that the TV will turn on
automatically.
You can select Everyday,
Mon-Fri (Monday through Friday), or the
individual days of the week.
Figure 1. TIMER menu (Set Day)
Input
(Figure 2)
Select the input to use when the timer turns on
the TV. If the TV is already on, the timer will
turn the TV to this selected input.
Figure 2. TIMER menu (Input)
Channel
(Figure 3)
If the selected input is for Ant-A or Ant-B, the
timer will turn the TV to the selected channel.
Figure 3. TIMER menu (Channel)
Part II1: Setup
ADVANCED FEATURES Menu: CONVERGENCE
CONVERGENCE
Menu
(Figure 1)
Your Mitsubishi TV has three picture tubes
which are aligned to properly converge the
projected light beams on the screen. Each
picture tube projects a single color of red, blue
or green. During production, your TV was
carefully adjusted to properly align these colors.
As a special feature, you have the ability to
adjust the red and blue light beams in reference
to the fixed green light beam. This process
is called convergence.
Convergence aligns
the entire screen at once. Select either Red
Figure 1. CONVERGENCE
menu
Convergence
alignment.
or Blue Convergence
Convergence
to begin
Screen
(Figure 2)
When the Red and Blue crosshairs are properly
converged, the center-screen crosshairs will
appear white. You can use A, V, <, or I_
to move the Red and Blue crosshairs.
Press
VIDEO to switch between Red and Blue. Press
AUDIO for the Advanced
Convergence
screen.
Advanced Convergence
Figure 2. Convergence screen
(Figure 3)
After adjusting the Red Convergence and Blue
Convergence, you can fine-tune your TV by
adjusting the Red and Blue convergence at 64
individual points. Move the flashing bracket to
a position needing adjustment by pressing A, •
<, or I_. Press ENTER to select the position
(flashing will stop). Move the Red or Blue line
by pressing A, •, <, or I_. Press VIDEO to
switch between the Red and Blue lines. A
Figure 3. Advanced Convergence screen
position is properly converged when all three
lines combine to appear white. Press ENTER to
deselect the position (flashing will resume), and
move the brackets to the next position
needing adjustment.
When completed, press
MENU to save your changes, and exit the
Advanced Convergence screen.
,ADVANCED FEATURES Menu: Reset Convergence,
Mute, Black Enhancement
Video
RESET FACTORY DEFAULTS
(Figure 1)
If you do not want to reset the convergence,
press the MENU key to return to the
Convergence menu without performing a reset.
Figure 1. RESET CONVERGENCE
DEFAULTS
TO FACTORY
You may reset the red and blue convergence to
factory default settings when you first use your
TV or after making manual changes. Press
the ENTER key to restore the convergence
to the default settings. All the changes you
made manually will be deleted. The message
"Convergence Completed" appears when the
convergence reset process ends.
Video Mute
(Figure 2)
Video Mute lets you display a blue or gray
background when no signal is being received
Inputs 1-3, DTV, and Component 1-2.
Black Enhancement
(Figure 2)
The contrast
in dark scenes
better picture quality.
be affected.
Figure 2. Video Mute/Black
Enhancement
is enhanced
for
Brighter scenes will not
on
Part II1: Setup
ADVANCED FEATURES Menu: Color Balance
Color Balance
(This feature only applies to 480i signal sources
affecting all inputs.) (Figure 1)
Your Mitsubishi
TV uses six basic colors
(Magenta, Red, Yellow, Green, Cyan and Blue)
for color balancing. You may refine the colors
on your TV screen automatically or manually.
You can also reset the colors to the default
settings,
if you prefer.
Auto Color Correction
(Figure 2)
Figure 1. COLOR BALANCE
Set the Auto Color Correction option to On to
optimize skin tone color. Both Manual Color
Adjustment and Reset Color options are grayed
out and unavailable when On is selected for
Auto Color Correction.
Manual Color Adjustment
(Figure 3)
Press Enter to display the menu for manual
color adjustment. The menu includes sliders
for Magenta, Red, Yellow, Green, Cyan and
Blue. The default for each color is center. The
slider you are adjusting
highlighted text.
is for the color with the
Note: The color bar test pattern signal found on
certain DVDs and non-broadcasting
TV stations
can be used in conjunction with this adjustment.
Figure 2. Auto Color Correction
Press Adjust ,& or v to navigate between colors
and Adjust • or • to change the color slider
settings.
The Manual Color Adjustment option is only
available when Auto Color Correction is turned
Off.
Reset Color
(Figure 2)
Figure 3. Manual Color Balance screen
Use the Reset Color option to reset to the
factory default settings used for Auto
Correction.
"Reset Completed" appears when
the color reset is complete.
Reset Color is only available when Auto Color
Correction is Off.
AUDIO/VIDEO
SETTINGS Menu: Audio Output
AUDIO/VIDEO
SETTINGS
Menu
(Figure 1)
Each of the seven or eight inputs has its own
AiV memory. You can adjust each input's AiV
memory in two ways. You can use the menu or
the remote control.
A/V Memory Reset
AiV Memory Reset will return the currently
selected input's AiV memory to the factory
settings. To reset an input's AiV memory, select
AiV Memory Reset, select the input you want to
reset, and press ENTER.
TV Speakers
This selection
Figure 1. AUDIO/VIDEO SETTINGS menu
(A/V Memory Reset)
will turn on or off the TV's internal
speakers. You may select Off when sending
the sound through a separate stereo system or
surround sound AiV receiver.
Audio Output
Select Fixed if your audio receiver or stereo
system can be controlled with a remote. This
allows you to adjust the volume with the
system's remote control or the TV remote
control, if compatible. This setting is better for
surround sound receivers. Select Variable if
your audio receiver or stereo system cannot be
controlled with a remote. This allows the TV's
internal circuitry to adjust the volume.
AUDIO SETTINGS and VIDEO SE-I'rlNGS
VIDEO
INPUT
CHANNEL
VOLUME
After selecting AUDIO SETTINGS or VIDEO
SETTINGS, you can adjust the settings by
pressing A, V, •, or •. For descriptions of
the individual AiV settings see A/V Setting
Descriptions, pages 49-50.
Using the AUDIO and VIDEO Buttons
on the Remote Control
(Figure 2)
Figure 2. The AUDIO, VIDEO, and ADJUST buttons.
0
Press AUDIO or VIDEO to cycle through
available settings.
the
[]
Press • or • to adjust the setting. After 5
seconds of inactivity, the setting display will
disappear.
Part II1: Setup
A/V Setting Descriptions: Audio
Audio Settings
[]
Bass enhances or reduces low frequency
sound.
Treble enhances
sound.
or reduces
high frequency
Balance adjusts the level of sound between
the left and right speakers.
Surround creates simulated stereo and
surround effects. Your choices are:
• Off: No surround
effects.
Use this
setting when using an AiV receiver with
Dolby TM Pro Logic Surround, or Dolby TM
Digital Surround.
• Simulated
Stereo: Your TV will create a
simulated stereo effect when watching a
non-stereo program.
• Surround
Sound: Your TV will create a
simulated surround
a stereo program.
effect when watching
Listen to (for Ant-A and Ant-B) determines
how your TV will receive a broadcast audio
signal and play back the sound you hear.
Your choices are:
• Stereo: Default setting. The TV will play
stereo broadcasts in stereo and mono
broadcasts in mono. The word "Stereo"
will be displayed when you tune to a
channel broadcasting stereo.
• SAP (Second Audio Program):
Additional monaural soundtrack that you
cannot hear during normal TV viewing.
The SAP signal might be related to the
program you are watching, such as a
soundtrack in a foreign language, or
unrelated to the program you are
watching such as a weather report. If a
SAP signal is broadcast, the letters "SAP"
will be displayed when you tune to the
channel.
• Mono:
should
stereo
played
Listen
Reduces background noise and
be used when receiving a weak
audio signal. All audio will be
mono with this setting.
to (for INPUTs) is not available.
Level Sound automatically equalizes
the volume level of programs containing
significant level differences from one
segment to another (for example, regular
programming to commercials).
To receive
the best fidelity with music programs, you
can turn this setting to Off.
Video
A/V Setting Descriptions:
Video Settings
€= Contrast
provides a slider to adjust the
white-to-black
level. Low contrast shows a
variety of shades in darker images, while
high contrast shows darker images more
uniformly black and makes colors appear
more vibrant.
Brightness provides a slider to adjust the
overall brightness of the picture.
Sharpness
provides
detail and clarity.
[]
Color provides
intensity.
a slider to adjust the
a slider to adjust the color
Color Temp (Color Temperature) allows
you to adjust how white images are
displayed. Your choices are:
• Low 6500K or Low (for DTV): White
images will have a warm cast to them.
This adjustment is an average and can
vary due to ambient room lighting, video
scene brightness and the TV's age.
The Low 6500K represents the 6500K
industry standard for NTSC (non-DTV)
pictures.
• Medium: White images will be balanced
between the Low (warm) and High (cool)
settings.
• High: White images will have a cool cast
to them. This setting may provide the
most realistic picture under bright lighting.
Noise
(graininess)
Video media uses a video camera created at
30 frames per second. Film media uses a
film camera created at 24 frames per second.
Examples of video media are live TV broadcast
such as news, special events, or video taped
programs.
Examples of film media are motion
pictures, made-for-TV movies, and many prime
time programs. Filmed media is converted by
the broadcaster or home video company to
30 frames per second to match TV or video
standards.
This conversion can leave subtle
"picture artifacts"
Tint provides a slider to adjust the
proportion of red to green.
Video
Film Mode (Automatic)
reduces
minor noise
in the broadcast
or input signal.
or conversion
errors.
The settings are On and Off. If you select
On, the system automatically detects if the
signal source is Film and corrects for conversion
errors. If you select Off, the system will never
correct for conversion errors.
Velocity Scanning
(VSM) Sharpness
Modulation
When turned On selected image
emphasized, resulting in sharper
The default is On. When turned
scanning modulation function is
outlines are
images.
Off, the velocity
prevented.
Part II1: Setup
Warning:
Do not leave stationary or letterbox images on-screen for
extended periods of time. Mix the types of pictures shown.
Uneven picture tube aging is NOT covered by your warranty.
The normal use of a TV should include a
mixture of TV picture types. The most
frequently used picture types should fill the
screen with constantly moving images rather
than stationary images or patterns. Displaying
the same stationary patterns over extended
periods of time or displaying the same
stationary pattern frequently may leave a
subtle but permanent ghost image. To avoid
this, mix your viewing pattern. Do not show
the same stationary image for more than 15%
of your total TV viewing in any given week.
Display constantly moving and changing
images that fill the screen whenever possible.
This projection TV uses picture tubes to project
the image to the screen. All picture tubes
age with use. As they age, their light output
is gradually reduced. Normal TV pictures fill
the screen with constantly changing images.
Under these conditions, picture tubes age at
an even rate across the entire screen. This
maintains a TV picture that is evenly bright
over the whole screen. Stationary images
or images that only partially fill the screen
(leaving black or colored bars to fill the screen),
when used over extended periods of time or
when viewed repeatedly may cause uneven
aging of the phosphors and leave subtle
ghosts of the stationary images in the picture.
Still or stationary images may be received
from broadcasters,
cable channels, satellite
channels, DVD discs, video tapes, laser
discs, on-line services, webilnternet
searching devices, video games, and digital
TV tuner/converter
boxes. Examples of these
types of images can be, but are not limited to
the following:
[]
Letterbox
top/bottom
black bars:
shown at the top and bottom of the TV
screen when you watch a widescreen
(16:9) movie on a standard (4:3) TV.
Side bar images: solid bars shown
on each
side of an image
watching
a standard
a widescreen
(16:9)
(4:3)
TV.
when
program
on
Stock-market
report bars: ticker
running at the bottom of the TV
screen.
Shopping channel Iogos & pricing
displays: bright graphics that are
shown constantly or repeatedly in the
same location.
Video game patterns and scoreboards
Bright station Iogos: moving or
low-contrast graphics are less likely
to cause uneven aging of the picture
tubes.
Online (Internet) websites: or any other
stationary or repetitive computer style
images.
Closed Captioning
rRemote
Control Functions: Overview
Overview
(Following page, Figure 1)
gll Slide Switch: Select AiV product to be
controlled by the remote control.
[] Numbers:
Individually select channels or
input information into TV.
[] POWER: Turns power on and off for TV and
other AiV products.
L_I SQV (Super Quick ViewTM): Scan through
a memorized list of favorite channels.
[]
QV (Quick ViewTM): Switch to last channel
viewed.
I'R HOME THEATER:
Enables the System
4 Home Theater Control. Once enabled, a
press of this key (when in the VCR, DVD,
or CableiDTViDBS
layer), will automatically
switch the inputs of the AiV receiver and
the TV. (WS-55411, WS-65411 and WS-73411
ONLY)
kl SLEEP: Set the TV to turn off within 2
hours. See Sleep Timer, page 56, for setup
instructions.
IN VIDEO: Select the video settings.
1121AUDIO: Select the audio settings.
• 1 MUTE: Turn sound on or off.
ffl INPUT: Select the signal to view
(Ant-A, Ant-B, DTV, Input-l, Input-2, Input-3,
Component-I,
or Component-2).
[] CHANNEL:
Scroll up or down through
memorized channels.
• ] VOLUME: Change sound level.
ml ENTER/EXCH:
Select a channel number
or menu item. Exchange PIP or POP and
main TV picture.
• 1 HOME: Exit on-screen
to TV viewing.
m
ADJUST:
settings,
location.
menus and return
Navigate menus, change
and move the PIP on-screen
CANCEL:
entries.
Clear SQV and some menu
MENU" Display !_I_M_ ®on-screen
menu
system.
• 1 INFO:
Display on-screen summary of
the current input used and any broadcast
information available (including current
V-Chip information, Signal Source and
Format). Additionally, if you press the INFO
key, it will display time, day and sleep time.
I_J GUIDE: When the slide switch is set
to CABLEiDBSiDTV,
display the on-screen
program guide (some cable boxes and
DBSiDTV receivers).
[] V-CHIP: Enable/Disable
the V-Chip Lock.
k'_ FORMAT: Change the shape and size of the
main TV picture.
k'_ PIP INPUT: Select the PIP or POP input
source.
I_ PIP/POP: Cycle through PIP and POP
display choices.
k'_ PIP OH: Scroll up or down through
memorized channels in PIP or POP.
Ft_JREC: Manually record with your VCR.
k'_ STOP: Stop your VCR, DVD, or CD.
F'_ PAUSE: Pause your VCR, DVD, CD, or
freeze the PIP or POP image.
k'_ REW/REV: Rewind or reverse search with
your VCR, reverse scan with your DVD, or
skip reverse with your CD.
[] PLAY: Play your VCR, DVD, or CD.
[] FF/FWD: Fast forward or forward search
with your VCR, fast play with your DVD, or
skip forward with your CD.
Part IV: Operation
Remote Control Functions: Care and Operation
Operation
Installing
the
Batteries:
(Figure 2)
[]
Remove the remote control's back cover
by gently pressing the ridged tab in the
direction of the arrow and sliding off the
cover.
[]
Load the batteries,
polarities
making sure the
(+) and (-) are correct.
For Best Results from the Remote
Control"
REC
STOP
REW/REV
_
PLAY
LmJBe within 20 feet of the equipment.
E"J Do not press two or more buttons at the
same time unless instructed to.
LmJDo not allow to get wet or become heated.
LmJAvoid dropping on hard surfaces.
LmJDo not use harsh chemicals to clean. Use
only a soft, lightly moistened cloth.
LmJDo not mix new and old batteries.
LmJDo not heat, take apart, or throw batteries
into fire.
PAUSE
FFIFWD
MITSUBISHI
LmJUse only AAA batteries.
Operating
Figure 1. Remote Control Functions.
the Remote
You can use the remote to control the TV,
CABLEiDBSiDTV,
VCR, DVD, and AUDIO
products. Select the product you want to
control by moving the slide switch (g of Figure
1) to the appropriate position. The remote
control has been preset to operate the TV
and other Mitsubishi products. To program
the remote control to operate other products,
see Use of the Remote Control with Other A/V
I ;fsze A
[]
batteries
O0
Products,
Figure 2. Installing the batteries.
| PORTANT
Control:
pages 26-27.
Remote
Control Functions: Channel Selection, Sleep Timer
Channel Selection
For Non-DTV
[]
Channels:
Enter three numbers
002).
(for channel 2, press
or
Press the channel number and ENTER (for
channel 2, press 2, then ENTER).
or
Enter the channel number
seconds.
and wait four
The TV will change
automatically.
Sleep Timer
Setting the Sleep Timer:
Press SLEEP on the remote control.
A message indicating the length of time
the sleep timer is to be set appears on
the TV screen.
Each press of SLEEP will increase
the time displayed by 30 minutes, until
the maximum value of 120 minutes is
reached.
After 5 seconds of inactivity, the
message will disappear.
Press SLEEP to view the remaining time
before the timer turns the TV off.
Canceling
the Sleep Timer:
Press SLEEP to display the on-screen
message.
Press SLEEP repeatedly until OFF is
displayed. After 5 seconds of inactivity,
the message will disappear.
Part IV: Operation
Remote Control Functions:
System 4 Home Theater IR Control
The Mitsubishi Home Theater IR System
Control is a special feature that makes it easier
to use your TV with a Mitsubishi digital AiV
receiver. Once your equipment is properly
connected and set up, your TV and Mitsubishi
digital AiV receiver will change inputs together,
to match high resolution pictures with the proper
surround sound. See How Connections Affect
the System 4 Home
14-15, for installation
Theater IR Control, Pages
instructions.
When you change inputs on your TV to watch
different video products, your TV will send
signals via the infrared emitter to your Mitsubishi
digital AiV receiver and will also change inputs
to hear the sound from that product. You
will automatically
hear the high quality digital
surround sound from digital products like your
DTV receiver and DVD, and high quality analog
stereo or surround sound from non-digital
products
like your VCR.
As you change TV inputs, the AiV receiver
changes its source for sound.
(ws-55411,
WS-65411
and WS-73411 ONLY)
Remote
Control Functions: Special Functions
When your remote control has been Programmed to operate another manufacturer's
)roduct, the function performed on each layer may vary. The most common functions
• POWER
• CHANNEL
up/down
• POWER
• CHANNEL up/down
• 0-9 Number Buttons
• PLAY
•REC
•ADJUST
up/down/left/right
(on some models)
• GUIDE (on some models)
•VOLUME
• Direct Input Selection
• POWER
• MENU
• 0-9 Number
• FF/FWD
• REW/REV
• ENTER (on some models)
•CANCEL
(on some models)
(on some models)
• POWER
• PLAY
• PAUSE
•STOP
Buttons
• FF/FWD
•PLAY
•STOP
Buttons
are:
• MUTE
-use number buttons, SQV, and QV (on some models)
• REW/REV
•ARROW up/down/left/right
(on some models)
(on some models)
• PAUSE
•PAUSE
•REW/REV
•CANCEL
•ENTER
•STOP
(on some models)
Remote Control Functions: Operation of PIP and POP
Picture-In-Picture
(PIP) and Picture-OutsidePicture (POP) features allow you to view
Programming in different ways. While watching
the main screen, you can display programs from
other channels and other inputs. To see which
inputs can and cannot be used together, see
How Connections Affect the PIP and POP Table 1, page 14. You can display large and
small PIPs, side-by-side pictures, three POPs,
or nine POPs.
Activating the PIP and POP
Figures 1-4 on following page/Figure
1-5 on page 62
Press PIP/POP to choose a display format.
Each time the PIP/POP button is pressed on
the TV remote control (within 3 seconds of each
other), the PIP/POP cycles through the following
display options.
n
[]
[]
I_1
[]
POP:
POP:
PIP:
PIP:
POP:
side-by-side pictures
three POPs
large PIP
small PIP
nine POPs (Widescreen
models Only)
To turn PIP/POP Off, wait at least 10 seconds,
and press PIP/POE The next time you activate
PIP/POP, the last used PIP/POP format will be
displayed first.
Part IV: Operation
Operation of PIP and POP
4:3 Narrow Screen Set: Models VS-50111 and VS-60111
You have the option to view two TV shows or inputs at the same time. For example,
watch a game show or a sports event on another channel or a DVD movie. The PIP
allows you to view another input as a picture-inside-picture.
The POP option allows
a main picture and another input as a side-by-side or three pictures-outside-picture
(only one moving POP).
Changing
you can
option
you to view
at the side
PIP/POP Inputs
Press PIP INPUT to browse through available
=1
PIP or POP images.
MAIN
PICTURE
Side-by-Side
Changing
PIP/POP Channels
Press PIP CH to scroll up or down through
memorizes channels on the Ant-A and Ant-B.
Exchanging Program Images
Press ENTERiEXCH
to exchange the main
picture with the PIP / POP picture.
POP
[]
MAIN
PICTURE
Moving PIP Images
POP
Press ADJUST A, v, <, or • to move the PIP
display anywhere on the main screen.
POP3
Automatic
Ar_-A002KCBS
$[ar_ard
PIPA017
%_-PGDLSV
SQV-1
[]
POP Switching
When automatic POP switching is active, the TV
cycles through memorized channels, or strobe
pictures from other AiV components in the
POP display. Press PAUSE to activate/pause
automatic POP switching.
Selecting
POP "Live"
Press ADJUST
Image
A, v, <, or • to select a
different POP "live" image (automatic
switching must be paused).
PIPA017
SQV-i
D
POP
Freeze the PIP and Side-By-Side
Picture
Press PAUSE to freeze the PIP and side-by-side
images. Press Pause again to return to a "live"
image.
4:3 Display Formats (Picture Shape)
VS-50111
& VS-60111
only
Your Mitsubishi narrow screen TV (also known as 4:3 TV) reflects several types of display formats
depending upon the type of input available for HDTV and many DVD images.
By pressing
FORMAT on the TV remote control,
you may select from four available
ml Standard
- default format fills the screen with the entire picture and squeezes
definition) pictures.
[]
Expand
[]
HD (high
- enlarges the picture and crops off some of the image at each side. This is useful to
correct distorted
[]
formats:
HDTV images and fill the screen (Only available for 1080i images).
Zoom - enlarges the picture, cropping off some of the image at each side. The Zoom
format is useful when you want to remove or reduce the black top and bottom bars
(only available for 480i/480p
images).
Letterbox
Letterbox
- (HD 1080i signals only) fills the screen and adds gray bars on top and bottom. The
format displays the correct aspect ratio ideal for widescreen viewing, with a vertical
picture area resolution
of 810i.
IMPORTANT:You can find aspect ratios on the back of most DVD covers.
are usually marked "Anamorphic" or "Enhanced for 16:9 TVs."
Format (picture shape) availability
INPUTS
Standard
based on Input/Signal
Zoom
Also, Anamorphic
Source(s):
Expand
Letterbox
Ant-A 000
Ant-B 000
YES
YES
YES
YES
NO
NO
NO
NO
DTV 480i/480p
DTV (1080i)
Input-1
Input-2
Input-3
YES
YES
YES
YES
YES
YES
YES
YES
NO
YES
YES
YES
YES
NO
NO
YES
NO
NO
NO
NO
YES
NO
YES
NO
NO
NO
NO
YES
Component-1
(480i/480p)
Component-1
(1080i)
DVDs
Part IV: Operation
For the 4:3 Models
Note the difference
Normal
between the appearance
Broadcast
Picture
(4:3)
of figures in Normal Broadcast
Widescreen
and Widescreen
Picture
Picture.
- HD 1080i
(16:9)
Standard
Standard
(Recommended)
(Not Recommended)
Zoom
Expand
(Recommended for Letterbox)
(Recommended for Broadcast with Black Side Bars)
Letterbox
(Recommended)
Operation
of PIP and POP (16:9 Widescreen
Set)
Picture Inside Picture (PIP) vs. Picture Outside Picture (POP)
You have the option to view two TV shows or inputs at the same time. For example, you can
watch a game show and a sports event on another channel, or a DVD movie and more. The PIP
option allows you to view another input as a picture-inside-picture.
The POP option allows you to
view a main picture and another input as a side-by-side or three or nine pictures-outside-picture
at the side (only one moving POP).
Changing
PIP/POP
Inputs
Press PIP INPUT to browse through
O
MAIN
PICTURE
available
PIP or POP images.
Side-by-Side
Changing
PIP/POP Channels
Press PIP CH to scroll up or down through
memorizes channels on the Ant-A and Ant-B.
POP 1
[]
MAIN
PICTURE
Exchanging
Program Images
POP 2
Press ENTERiEXCH
to exchange the main
picture with the PIP / POP picture.
POP 3
Moving PIP Images
Press ADJUST
Ant-A 002 KCBS
S_andard
TV-PG DLSV
SQVq
PIPA 012"
display anywhere
Automatic
[]
A, V, <, or • to move the PIP
on the main screen.
POP Switching
When automatic POP switching is active, the TV
cycles through memorized channels, or strobe
pictures from other AiV components in the
POP display. Press PAUSE to activate/pause
automatic POP switching.
Ant-A 00_2KCBS
Standard
TV-I_G DLSV
SQV-1
PIPA 012"
Selecting
POP "Live"
Image
Press ADJUST A, V, <, or • to select a
different POP "live" image (automatic POP
switching must be paused).
Lq
Freeze the PIP and Side-By-Side
Picture
[]
POP 1
MAIN
PICTURE
POP 2
POP 3
POP 4
POP 5
POP 6
POP 7
POP 8
POP 9
Press PAUSE to freeze the PIP and side-by-side
images. Press Pause again to return to a "live"
image.
Part IV: Operation
For the 16:9 Models
Widescreen
Picture (16:9 - HD 1080i only)
For Example: A True HD Broadcast
Standard
(Recommended)
Expand (Recommended for 4:3 images with Black Side Bars)
Format
INPUTS
(picture
availability
Expand
48oi/48op
Expand
lo8oi
based on Input/Signal
Zoom
Stretch
Narrow
AnL-A 000
Ant-B 000
YES
YES
YES
YES
NO
NO
YES
YES
YES
YES
YES
YES
DTV 480i/480p
DTV (1080i)
YES
YES
YES
NO
NO
YES
YES
NO
YES
NO
YES
NO
Input-1
Input-2
Input-3
Component-1
(10800
YES
YES
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
YES
YES
YES
YES
YES
NO
YES
YES
YES
YES
NO
YES
YES
YES
YES
NO
Component-2(480i/480p)
Component-2(10800
YES
YES
YES
NO
NO
YES
YES
NO
YES
NO
YES
NO
Component-1
Standard
shape)
(480i/480p)
6:9
Display Formats (Picture Shape)
Wide Screen Models
Only
Your Mitsubishi widescreen TV (also known as 16:9 TV) reflects several types of display formats
(picture shape) available for HDTV and many DVD images.
By pressing
FORMAT on the TV remote control, you may select from six available formats:
g Standard - default format for DTV and Component Input displays a full-screen format. The
Standard format displays Anamorphic DVDs that have the 1.78:1 or 1.85:1 aspect ratios.
However, Anamorphic DVDs that have the 2.35:1 aspect ratio still display black bars at the top
and bottom of the screen, while narrow (4:3) images are stretched evenly from side to side.
[] Expand (480i/480p)enlarges the picture, cropping some of the image at the top and bottom.
The Expand format is useful to reduce the letterbox top and bottom bars of non-Anamorphic
DVDs or to correct narrow 4:3 images that have been stretched in the Standard format.
Note: This format is not available
[]
in the 1080i format.
Expand (1080i) - enlarges the picture, cropping some of the image on both sides. This Expand
format is useful to remove or reduce black side bars on HD broadcasts of 4:3 images with
black bars (See page 63).
[]
Zoom - enlarges the picture, cropping some of the image at each side, top and bottom. The
Zoom format is useful to remove or reduce the black top and bottom bars on Anamorphic
DVDs with 2.35:1 aspect ratio.
Note: This format is not available
in the 1080i signal.
[] Stretched - is the default format for ANT-A and Ant-B, and Inputs 1-3. The Stretched format
stretches narrow 4:3 images across the screen, however, there is less stretch in the center
than the sides. The Stretched format allows the entire narrow image to be displayed across
the screen, however, there is less distortion in the center than in the sides.
Note: This format is not available
[]
in the 1080i signal.
Narrow format displays narrow 4:3 images in their original shape and adds stationary
bars to fill the screen. Note: This format is not available in the 1080i signal.
IMPORTANT: You can find aspect ratios on the back of most DVD covers.
DVDs are usually marked "Anamorphic" or "Enhanced for 16:9 TVs."
|MPGRTANT
gray side
Also, Anamorphic
Part IV: Operation
For the 16:9 Models
Note the difference between the appearance
of figures in Non-Anamorphic
Normal Broadcast Picture (4:3 - 480i/480p)
For Example: NON-ANAMORPHIC
Standard
DVDs
(Not Recommended)
(Left) and Anamorphic Widescreen (Right)
Widescreen
Picture (16:9
- 480i/480p)
For Example: ANAMORPHIC
Standard
pictures
DVDs
(Recommended)
Expand (Recommended for LetLerbox)
Expand (Not Recommended)
Zoom (Not Recommended)
Zoom (Recommended for 2.35:1 DVDs)
Stretched
Stretched
(Recommended for Standard Broadcast)
Narrow (Recommended for Occasional Use)
(Not Recommended)
Narrow (Not Recommended)
Appendix
A: Bypassing
the V-Chip
Lock
Appendix
A: Bypassing
the V-Chip Lock
Bypassing the V-Chip Lock
After you set the lock, you need your
passcode to view a V-Chip locked program,
view the locked TV, cancel the lock, or enter
the V-Chip lock menus.
If you forget your passcode, you can
view the locked TV without entering your
passcode.
This is done by pressing the
number 9 and QV buttons on the remote
TV control at the same time, when your
password is requested. This process
temporarily unlocks the TV.
=====
When entering the V-Chip Lock menu, this
process deletes your old passcode and
prompts you to enter a new passcode.
|mPQRTANT
|MPQRTANT
(1)
Appendix
Component-1 and Component-2
B: High Definition
Input Connection
Compatibility
Inputs
These inputs are compatible with most
standard DVD and DTV signals with component
video outputs. Compatible DTV signals are
SDTV 480i, 480p, and HDTV 1080i.
All other DTV signals, such as 720p, need to be
converted by the DTV receiver to one of the
compatible signal types. Please check the DTV
receiver specifications before connecting.
Input Levels with Component
[]Y
Pb
Video
=l.0Vp-p (includes sync) 75ohms
=700mVp-p, 75ohms (can also receive
signals from outputs labeled B- Y and
Cb)
L_J Pr
=700mVp-p, 75ohms (can also receive
signals from outputs labeled R-Y and Cr)
DTV Input
These inputs are compatible with most
standard DVD and DTV signals with component
video outputs. Compatible DTV signals are
SDTV 480i, 480p, and HDTV 1080i.
All other DTV signals, such as 720p, need to be
converted by the DTV receiver to one of the
compatible signal types. Please check the DTV
receiver specifications
before connecting.
Input Levels When Used With
Component
Video Signals
EIA - 770.3 Standard
_Y
E_J Pb
E_J Pr
[]H
_v
This input is also compatible with some DTV
receivers using RGB with "sync on green" or
RGB with "separate H and V sync." Industry
standards for DTV RGB signals systems,
synchronization,
timing, and signal strengths are
not currently established.
These inputs will
not be compatible with all DTV receivers that
offer RGB. If your DTV receiver offers both
DTV component video signals and DTV RGB
signals, Mitsubishi suggests you use the DTV
component video signals. Please check the
DTV receiver specifications
before connecting.
Levels
=l.0Vp-p (includes sync) 75ohms
=700mVp-p, 75ohms
=700mVp-p, 75ohms
=Not Used
=Not Used
Input Levels when Used With RGB
Video Signals
G (Y) =1.0Vp-p 75ohms
on green)
B (Pb)=700mVp-p,
R (Pr)=700mVp-p,
(compatible with sync
75ohms
75ohms
H =4Vp-p+i-l.0v, 2.2k ohms
(when using separate H and V sync)
V=4Vp-p+i-l.0v,
2.2k ohms
(when using separate H and V sync)
_.ppendix C: Remote Control Programming
A/V Receivers
Mitsubishi ........
..............
Admiral ..........
Aiwa ............
Denon ..........
Fisher ..........
Gerrard ..........
Harman Kardon ....
Jensen ..........
JVC ............
Kenwood ........
Magnavox ........
Marantz
........
Mclintosh ........
Nakamichi ........
Onkyo ..........
Optimus ........
Panasonic ........
Philips ..........
Pioneer ..........
Quasar ..........
RCA ............
Sansui ..........
Sharp ..........
Sony ..........
Sound-sigh
......
TEAC ..........
Technics ........
Victor ..........
Yamaha ..........
010, 011,012,013, 014
015
220
225, 226
234, 235, 236
204
213
215
223
232, 233
200, 208
227, 228
224
216
206,217
209, 214, 240
203, 227, 231,230
219, 218,221
223
205, 207
219, 218,221
203, 205, 227, 231,230
203, 211,239
234, 237
222
238
212,213, 210,211
221,218, 219
232, 233
201,202
DVD Players
Mitsubishi ........
Denon ..........
Ferguson ........
GE ............
JVC ............
Normande ........
Panasonic ........
PhilipsiMagnavox
Pioneer ..........
ROAiProscan ......
Saba ..........
Sony ..........
Thompson ........
Toshiba ..........
Yamaha ..........
Zenith ..........
003
250
251
251
257
251
250
.258
252
251,256
251
254
251
253
250
259
Satellite Receivers
Mitsubishi
HD/Satellite Receiver
Echostar/Dishnetwork
GE ............
Hitachi ..........
Hughes ..........
Panasonic ........
Philips ..........
RCA ............
Sony ..........
Toshiba ..........
Uniden ..........
006
175
176
173, 181
173
174
171,172
176, 179, 180
177
170
171,172
Codes
VCRs
Mitsubishi ........
001,002, 060,067, 068, 061,
..............
062
Admiral ..........
055
Aiwa .........
.04_ 052
Akai .........
.049,034,035,036
Audio Dynamic
.. .059,031
Bell & Howell.
.. .025,033
Broksonic .....
.040,046
Canon .......
.043,045
Citizen .......
.026
Craig
.. .025,049,026
Curtis M'ati_es[
.. • 065,044,047
Daewoo .....
.063,021,044,079
DBX .........
.059,030,031
Dimensia ......
065
Emerson ........
023, 038, 039, 040, 045, 046
..............
062,063
Fisher ......
025,028,029, 027,033
Funai . ..
... 04_ 046,040,054
GE .....
...05_
065,044
Go Video .
.. .05_069,070,071
Goldstar
...026
Gradiente .
...054
Hitachi...
.. . 043,065,020,047
Instant Replay
.. •044,043
densen .....
...059
JVC .......
.. .059,030,031,054,076,077
Kenwood ......
059, 030,026,031
LXI ............
047, 026,020,02_ 028,025,
..............
029
Magnavox ....
051, 043,044
Marantz
... 059, 030,031
Marta ......
026
Memorex ....
044, 029
MGA ......
058, 060,06_ 068,061,062
Minolta ......
020, O65
Multitech ....
067, 047,024
NEC ........
059,030,031,054
Olympic
...044,043
Optimus
... 048,041,055,026
Orion ......
046,040
Panasonic ....
043,044,041,042
Penney ......
044, 020, 065,025, 059, 030
..............
031
Pentax ..........
020,031,065
Philco ..........
051,044,04_ 043,046,040,
..............
063
Philips ..........
051,043,044
Pioneer ..........
043
Proscan ........
065,020,043,044,051,066
..............
021,022,053
Quasar ..........
041,042, 043,044
Radio Shack ......
053,044,025,056,029,060
..............
047
RCA ............
053,065,020,043,044,049
..............
051,066,021,022,079
Realistic ........
044,025,056,029,060,047
Samsung ........
05_ 022,024,053
Sansui ..........
059,046,040,072
Sanyo ..........
025,029,033
Scott ..........
021,022,024,029,058,060
..............
06_ 068,046,040
Sears ..........
025,026, 02_ 028,020
Shaintom ........
037
Sharp ..........
055, 056
Signature 2000 ....
047, 055
Singer ......
037
Sony ..........
048, 049, 050,073,074, 075,
..............
079
SV2000 ........
047
Sylvania .
... 051, 043, 044,047
...047
Symphonic
Tashiro...
...026
Tatung . ..
...059,
030,031
TEAC
.. .059, 030,047,031
Technics
.. • 032, 041,042,043,044
Teknika .....
.044, 047
Toshiba .....
• 021
Totevision .
.. .026
Vector Research
.. • 031
Wards .......
.055,056,029,064,026
Yamaha .....
... 025,059, 030, 031,031
Zenith .....
.....
064,026
Cable Box
ABC ............
Archer ..........
Cableview ........
Citizen ..........
Color Voice ......
Comtronics
......
Curtis ..........
Diamond ........
Eagle ..........
Eastern ..........
GO Brand ........
GE ............
Gemini ..........
General Instrument
iJerrold
........
..............
Hamlin ..........
..............
Hitachi ..........
Macom ..........
Magnavo× ........
..............
Memorex ........
Movietime ........
Oak ............
Panasonic ........
Paragon ........
Philips ..........
..............
Pioneer ..........
Pulsar ..........
Puser ..........
RCA ............
Realistic ........
Regal ..........
..............
Regency ........
Rembrant ........
Samsung ........
Satellite.
Scientific Atlanta ....
Signature ........
..............
SL Mark ........
Sprucer ..........
Starcom ........
..............
Stargate ........
Teleview ........
Texscan
........
Tocom ..........
Toshiba ..........
Unika ..........
United Artists ......
United Cable ......
..............
Universal ........
Videoway ........
Viewstar ........
Zenith ..........
124
132, 125
105, 132
122, 105
128, 129, 130, 106, 107
128, 129, 130,106, 107
112, 113
124, 132, 125
129
134
132, 105
111,112, 113
122, 143
111,119, 120, 121,122,
123 124, 125, 126, 127
140, 141,142, 145, 118,
112
103, 124
103, 104, 105, 108
128, 129, 130, 106, 107,
133, 138
130
132
139, 137, 102
109, 110, 114
117
128, 129, 130, 106, 107,
133, 138
101,116
105, 132
132
115
132
112, 118, 140, 141,142,
145
134
137, 132, 105, 138
105
.100
111,112, 113
119, 124, 125, 126, 127,
120, 121,122, 111
105, 101
105, 110
119, 124, 125, 126, 127,
120, 121,122, 111
132, 105
101,105
144
135, 136
104
132, 125
139, 137, 102
119, 124, 125, 126, 127,
120, 121,122, 111
122, 132
106
129, 130
117,100
Appendix
D: Cleaning
and Service
Cleaning
Normally, light dusting with a dry,
non-scratching
duster will keep your TV clean.
If cleaning beyond this is needed, please use
the following guidelines:
Cloth speaker
[]
grills:
Lightly brush with a soft brush.
E_J If necessary,
you can vacuum
using the
brush and hose attachments of your vacuum
cleaner. Do not use the beater brush section on
the grill cloth.
General
Top and sides of the TV:
Cleaning
Warnings:
DO NOT allow liquid to enter the TV through
Gently wipe down your TV with a soft,
non-abrasive cloth such as cotton flannel or a
the ventilation
clean cloth diaper, lightly moistened with water.
Dry with a second dry, soft, non-abrasive cloth.
DO NOT use any strong or abrasive
cleaners as these can scratch the surfaces.
For oily dirt, add a few drops of mild liquid
detergent, such as dishwashing detergent to the
water used to moisten the cloth. Rinse with a
second cloth moistened
only with water.
with a third dry, soft, non-abrasive
Dry
cloth.
slots or any crevice.
E_J DO NOT use any cleaners with ammonia,
bleach, alcohol, benzine, or thinners as these
can dull the surfaces.
L"_ DO NOT spray liquids or cleaners
the TV's surfaces.
directly on
DO NOT scrub or rub the TV harshly.
Screen behind the Diamond
E_J Follow the instructions
it gently.
ShieldTM:
for the top and sides,
however, wipe gently in an up and down motion,
following the grooves in the screen.
Clean the entire screen evenly, not just
sections of the screen.
Do not allow liquid to drip down the grooves
of the screen as some liquid may enter the TV
between the screen and the screen frame.
You may purchase Mitsubishi Screen
Cleaner, part number CLEANING-VSS,
calling (800) 553-7278.
|MPGRTANT
by
|MPGRTANT
Wipe
pendix E: Diamond
Shield Instructions
Diamond Shield
TM
Installation and Removal Procedure
(WS-48311)
Follow the steps below to install and remove the
Diamond Shield TM
INSTALLATION
Note:
Included
package
in the Diamond
are the following
[]
[]
(1) Diamond Shield
(2) Molding Clips
[]
Carefully
protective
cloth.
items:
TM
packaging.
starting
Diamond Shield
Diamond Shield
[]
TM
remove the Diamond Shield
Begin by inserting
channels,
Shield
TM
TM
TM
from its
Wipe off any dust with a lint-free
the shield, sliding it into the
at the bottom.
Gently bow the
toward you and insert the
into the top channel.
Install the left and right molding clips by pressing
them into the opening starting at a corner. Do not
force the clip. The clip will slide into place. This
completes
the Diamond
Shield
TM
installation.
REMOVAL
To remove the Diamond Shield
the above procedure.
TM,
reverse the order of
Appendix
Diamond Shield
TM
E:
Diamond
Shield Installation
and
Installation and Removal Procedure
(VS-50111, VS-60111, WS-55311, WS-55411, WS-65311, WS-65411, WS-73411)
Follow the steps below to install and remove the
Diamond Shield TM
INSTALLATION
Note:
Included
package
in the Diamond
are the following
[]
(1) Diamond Shield
[]
(2) Molding Clips
[]
Carefully
protective
cloth.
[]
Shield
TM
items:
TM
remove the Diamond Shield
packaging.
Begin by inserting
TM
from its
Wipe off any dust with a lint-free
the shield, sliding it into the
channels, starting at one side. Gently bow the
Diamond Shield TM toward you and insert the other side
of the Diamond Shield
TM
into the oppositive
channel.
Install the top and bottom molding clips by pressing
them into the opening
starting
at a corner.
Do not
force the clip. The clip will slide into place. This
completes the Diamond Shield TM installation.
REMOVAL
To remove the Diamond
Shield
TM,
reverse the order of the above procedure.
Removal
Cabinet Separation for Models WS-65411 and WS-73411
Instructions for Separating the Upper and Lower
Section of the Projection Television Cabinet
For Mitsubishi Dealers and Service Personnel ONLY
This Mitsubishi projection television cabinet has been assembled in two pieces.
These pieces may be separated to allow for easier delivery and setup.
The instructions below show how to safely separate and reattach the cabinet.
@This projection television weighs over 320 pounds
and has many sensitive components.
@This dismantling procedure should be done by
authorized Mitsubishi Dealers or Service Personnel
ONLY.
The following
people:
operations should be performed
_!e
binet-T°p
by two
en Frame
D Remove the decorative Plastic Covers (2) on each
side of the cabinet and then remove the exposed
_
Brackets
Screws (2) on each side.
____
Cabinet-Bottom
Carefully lift the Cabinet-Top straight up until the
Brackets are clear from the Cabinet-Bottom. DO NOT use
the Screen Frame when lifting the Cabinet-Top.
Carefully place the Cabinet-Top
on to the floor.
Once you have moved and positioned the CabinetBottom to its desired location, reverse the procedure and
mount the Cabinet-Top on the Cabinet-Bottom.
Be sure
you align the Brackets properly. Keep fingers clear of all
joints! Replace the Screws and the decorative Plastic
Covers that were removed in Step 1_
[]
Plastic Covers,
Screws
J
B
Appendix F: Cabinet Separation
Cabinet Separation for Model WS-65311
Instructions for Separating the Upper and Lower
Section of the Projection Television Cabinet
For Mitsubishi Dealers and Service Personnel ONLY
This Mitsubishi projection television cabinet has been assembled in two pieces.
These pieces may be separated to allow for easier delivery and setup.
The instructions below show how to safely separate and reattach the cabinet.
@This projection television weighs over 320 pounds and has many sensitive components.
_This dismantling procedure should be done by authorized Mitsubishi Dealers or Service
Personnel ONLY.
The following operations should be performed
people:
by two
Front Cabinet Disassembly Procedures
Remove the Speaker Grille by gently pulling both the right
and left side of the Speaker Grille away from the wood cabinet.
_]_ Undo the wire ties and disconnect the CC and ZF connectors.
O
Remove the Screws that attach the Screen Frame to the wood
Cabinet-Bottom. The Screws are located at the bottom portion
of the screen frame.
O
This operation should be performed by two people. Carefully
remove the Screen Frame by holding the sides and bottom
of the frame and lift the frame vertically off the Cabinet.
NEVER PULL THE SCREEN FRAME FROM THE TOP.
O
Place the Screen Frame in a location where nothing will come in
contact with the screens. The screens' surface can be damaged if
not properly handled.
Cabinet Separation Procedure
Remove the decorative Plastic Covers (2) on each side
of the cabinet and then remove the exposed
Screws (2) on each side.
_)
Carefully lift the Cabinet-Top vertically until the Brackets are
clear from the Cabinet-Bottom.
O
Carefully place the Cabinet-Top on the floor.
0
Hold Speaker
Grille here
J
f
Speaker Grille
Brackets
Cabinet-Top
Plastic Covers,
Screws
Cabinet Re-assembly
Once you have moved and positioned the Cabinet-Bottom
to itsdesired location, reverse the procedure and mount
the Cabinet-Top on the Cabinet-Bottom. Be sure you align
the Brackets properly. KEEP FINGERS CLEAR OF ALL JOINTS!
Replace the Screws and the decortive Plastic Covers that were
removed in step_.
Reinstall the ScreenFrame _]). Replace the
Screws per stepO. Place wires in the wire ties and join the connectors
per step _D. Reinstall Speaker Grille O.
O
. The TV remote controi does not work:.
.Be
remote
,The TV takes severat seconds to respond to.
channel commands
. You cannot access a channel:
.On-screen displays appear each time you change a functioni.
iiii
iiii i _
i i
Check that the batteries are installed correctly;
* Check that the selected switch is set to "TV
no further than 20 feet from the TV when using the
control,
Press ENTER after a channel number to avoid delays
Use the three digit number lie 002 for channel 2
• Use number keys instead of CHANNEL up/down:
• Be sure the Channe!you want to view is in memory:
• Check that the TVis turned to the correct input source for
that channet by pressing the INPUT button:
Make sure the V,Chip setting is off (page 40):
This is part of normal TV operation
. You Cannot program the TV to turn on automaticaliy
• The TV may be tockedi
• The clock may not be set
. There is no sound even when the volume is turned upl.
Check to see if the MUTE button is on
• The TV's !'Listen to:,' setting may be set to SAR
Check that TV Speakers setting _sON
. You have forgotten your iock passcodel.
. PIP does not disptay a picturei.
. The sound does not match the screen picture:
MONITOR
.There is a iarge black or gray rectangie on thiescreen: i i !!
See AppendixA, Bypassing the V ChipLockpage6&
Make sure the V-Chip setting is off (page 40):
Not a!! inputs Canbe displayed as a PiP (page 14)
• The TV s ,!Listen to!, setting may be set to SAP
• If using stereo or A/V reveiver speakerscheck input
selection onthe stereo or A/V receiver.
If using stereo or A!V receiver, check that AUDIO is from
OUT on TV,s back panet
.The TV closed captioning has been set to 'itext' model bui i i i
there is no text information!being broadcast; !Turn Off in tihe
CAPTIONSmenu(page35).
. You Cannot see a picture when you play a VCR tape
• If you connected your VCR with A!V cabies; use the INPUT
button to select the Input source (INPUT li INPUT 2, or
INPUT 3 ) that the VCR is connected tol
• Check your VCRs owner!s guide for further troubleshooting:
. V, Chip Lock is not working.
Make sure that V-Chip is On (page 40):
• If V,Chip HourslLock by Time is currently set to disable the
V-Chip !ock, the V,Chip wi!! not b!ock programming
ii
Appendix
Problem
Cannot set adjustments to factory settings
G: Troubleshooting
Possible Solution
•Follow the steps below to reset system defaults to factory
settings.
1. Press the MENU button followed by number buttons 1, 2,
and 3 on the remote control.
Result: The above steps activate the Reset System
Defaults menu screen.
2. Press the ENTER button on the remote control.
Result: The settings reset to factory defaults.
3. Press the HOME or MENU button on the remote control to
return to the HOME or MENU screen.
IMPORTANT: This function is not recommended unless it is
mandatory to reset system defaults to factory settings. This
operation CANNOT be undone and all custom settings will be
erased.
E
A
adding and deleting
Advanced
43 -47
channels,
Features
38
menu, 30,
espafiol,
32
maintenance,
EXCH button on remote, 54-55
(BNC to RCA), 20
adjusting
(convergence),
alignment
45-46
(convergence),
antennas
45-46
(connecting),
audio settings,
13, 16-17
48, 49
Auto Color Correction,
memory
F
Film Mode (Automatic),
formats
(display),
50
60-65
front control panel, 12
47
G
B
games,
ghost, 23, 51
Black Enhancement,
(enabling
H
46
V-Chip),
40-42
connection,
(V-Chip-Lock),
38
naming
inputs, 31
42
(PIP), 9, 14,
(POP), 9,
R
15
remote control
Settings
C
I
4, 69
Clock (setting),
compatibility
contrast,
channels,
14, 22, 57
remote control functions,
26-28, 54-58
cleaning,
naming
IR System
special setups,
66
38
Picture-outside-Picture
14, 58-59, 62
Home Theater
50
31
N
Picture-in-Picture
58-59, 62
bass, 49
bypassing
(channel),
passcode,
49
brightness,
channels,
47
F
23, 51
back panel, 13
blocking
color adjustment,
memorize
adaptors
balance,
manual
2, 74
33-34
(signal),
67
convergence,
NOTES,
Safeguards,
47
£
date (setting),
34
daylight
savings
dusting,
69
time (DST), 33
Video,
50
23, 51
channel
4-5
functions,
installing
45-46
Color Balance,
49
care and operation,
IMPORTANT
Important
50
Audio,
selection,
54-65
batteries,
programming
codes,
replacement,
6
reset convergence,
language,
32
letterbox,
23, 51, 60
Lock by Time, 42
55
56
55
26-27, 68
46
reset color, 47
Sleep Timer, 56
reset (A/V), 48
locked, 40-42
Quick View
TM
(QV), 54
Index
V
S
safeguards,
servicing,
V-Chip
4-5
bypassing,
2, 5
1080i, 14, 60-61, 63-65,
480i, 14, 60-61, 63-65,
480p (progressive
60-61, 63-65, 67
67
(adjusting),
Special
DVD), 14,
screen,
48-49
V-Chip
(Remote),
58
Velocity Scanning
(VSM), 50
stand,
Video Mute, 46
4
surface,
surges,
41
Hours, 42
ventilation,
WARNING,
41
V-Chip, 40,41
SQV (Super Quick ViewTM), 28,54
STATIONARY
42
ratings and categories,
signal information,
32
Functions
Lock by Time, 42
passcode
67
Sleep Timer, 56
Spanish,
66
entry to, 40
signal types
sound
Lock, 40-42
PICTURE
Modulation
4, 69
Video Settings,
50
23-51
4
4
Mitsubishi
3r"
time (setting),
34
Timer
(turn TV on), 43-44
Timer
(Sleep),
56
treble, 49
Troubleshooting,
TV speakers,
unpacking,
upgradeable,
74-75
48
9
9
Limited Warranty,
78
Limited Warranty
MITSUBISHIPROJECTIONTELEVISIONLIMITEDWARRANTY
MITSUBISHIDIGITALELECTRONICSAMERICA, INC.("MDEA") warrantsto the originalpurchaserof thistelevision that if purchasedfrom an authorized
MITSUBISHIAudio/Video Dealer,should it provedefective by reasonet improperworkmanshipand/or material:
a. Parts. Thelenticutar(i.e.front picture)screenand/or the DiamendShietdTM is warrantedagainst defectsin materialsand workmanshipfor a periodof 30 days.
All other parts are warrantedfor a periodot one yearfrom the date of the originalpurchaseat retail. Wewill repairor replace,at our option, any defective part
without chargefor the part. Parts usedfor replacementmay be replacedwith those of likekind and quality and may be newor remanufactured. Parts usedfor
replacementare warrantedfor the remainderot the originalwarranty period.
b. Labor. For 30 days after the originalpurchaseat retail, we will repair or replace,at our option,the lenticularscreen if it proves defective. Forall other parts,
we will providethe labor for a warrantyrepair by an authorizedMITSUBISHIservice center withoutcharge for one yearfrom the originaldate or purchaseat
retail.
c. Notice. To obtain warrantyservice, you must notify an authorizedMITSUBISHIservice center of any defectwithin the applicablewarranty timeperiod.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearestauthorizedMITSUBISHIservice center whose nameand addresscan be obtainedfrom your MITSUBISHIdealeror by writing or calling
MDEAat the addressand telephonenumber providedbelow.
b.Warrantyservice will be providedin your homeor, if required,at an authorizedservice shop, providedthat your television is locatedwithin the geographic
territory customarilycoveredby an authorizedMITSUBISHIservice center. If net,you must either deliveryourtelevision to an authorizedservice locationat
your own expense,or pay for any travel and/or transportationcosts the service centermay chargeto andfrom your home. Actual service laborwill be provided
without charge.
c. Proof of purchasedate from an authorizedMITSUBISHIdealeris requiredwhen requestingwarranty service. Presentyour salesreceipt or otherdocument
which establishes proofand date of purchase. THE RETURNOF THE OWNERREGISTRATIONCARD IS NOTA CONDITIONOF WARRANTYCOVERAGE.
However,pleasereturn the Owner RegistrationCard so that we can contact you should a questionof safety arise which could affect you.
2. THIS WARRANTYDOES NOTCOVERdamage to Diamond Shield,Lenticularscreen or Freenellens, screenframe, cosmeticdamage otto any other product
where such damage is caused byunauthorizedmodification,alteration,repairsto or service of the productby anyoneother than an authorizedMITSUBISHI
service center; physicalabuse to or misuse of the product(includingany failure to carry out any maintenanceas describedinthe Owner's Guideor any product
damaged byexcessivephysical or electricalstress); any productsthat have hada serial numberor any part thereof altered,defaced or removed; productuse in
any mannercontrary to the Owner'sGuide (including unevenpicturetube aging and imprinted imageson the viewingscreen); freightdamage; or any damage
caused byacts of God or otherfactors beyond the reasonablecontrol el MDEA, such aspower surge damagecaused byelectrical systemor lightning. This
warranty also excludesservice calls where no detect in the productcovered underthis warrantyis found, service calls relatedto unsatisfactoryaudio or visual
receptionor signal unless causeda defect in the productthat is coveredunder this warranty,all costs, expensesor any other damagesarisingfrom product
installation,or set-ups, any adjustmentsof usercontrols (includingconvergence,contrast,brightness, color,tint, fine tuning, sharpness),other adjustment
necessaryto preparethe unit for displayor use, connectionwith any externalaudio receiver,antenna, cable or satellitesystems, or service of products
purchasedor serviced outsidethe U.S.A. Pleaseconsult the operating instructionscontainedinthe Owner'sGuidefurnishedwith the productfor information
regardinguser controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION
OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY
PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE.
5. Some states de not allow limitations on hew long an implied warrarly lasts,or theexclusion orlimitationof incidental,special orconsequential damages,so
the above limitations or exclusionsmay notapply to you.
6. This warrantygives you specificlegal rights,and you may also have other rights whichvary from state tostate.
7. BEFOREREQUESTINGSERVICE,pleasereviewthe instructionbookletto insureproper installationand correctcustomercontrol adjustment. If the problem
persists,contactyour nearestMITSUBISHIDealerfor the name(s)of authorizedMITSUBISHIServiceCenter(s). If you are unableto obtain this information,
pleasecall 800-332-2119,or write usat the address below.
MITSUBISHIDIGITALELECTRONICSAMERICA,INC.
9351JeronimoRoad
Irvine,CA92618-1904
RETAIN THIS PORTION
FORYOUR
RECORDS
MITSUBISHI
I
SERIAL
MODEL
DEALER
NAME
STREET
ADDRESS
PHONE
NUMBER
NUMBER
NUMBER
ZIP
PURCHASE
DATE
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 79 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Mon Apr 02 23:34:06 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools