MTD 21AA412A700 User Manual REAR TINE TILLER Manuals And Guides 1109109L

410 Thru 420 1109109L

User Manual: MTD 21AA412A700 21AA412A700 MTD REAR TINE TILLER - Manuals and Guides View the owners manual for your MTD REAR TINE TILLER #21AA412A700. Home:Lawn & Garden Parts:MTD Parts:MTD REAR TINE TILLER Manual

Open the PDF directly: View PDF .
Page Count: 24

Operator's Manual

Rear Tine Tiller

Model Series

410 Thru 420

Model Series 410 Shown

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-

covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting

applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have

similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized

service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

PRINTED IN U.S.A. FORM NO. 770-10136D

(10/03)

Content

Important Safe Operation Practices

Assembling Your Tiller

Know Your Tiller

Operating Your Tiller

Making Adjustments

TABLEOFCONTENTS

Page Content

3 Maintaining Your Tiller

5 Troubleshooting

8 Illustrated Parts List

9 Warranty

Page

FINDINGMODELNUMBER

This Operator's Manual is an important part of your new tiller. It will help you assemble, prepare and

maintain the unit for best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the

equipment and copy the information from it in the space provided below. A sample model plate is

also given below. You can locate the model plate by standing at the operating position and

looking down at the center of the rear tine cover. This information will be necessary to use the

manufacturer's web site and/or help from the Customer Support Department or an authorized

service dealer.

P. O. BOX 3611131

CLEVELAND,OH 44136

330-228-4683

', www.m{uprOuuc_s.com 888-888-7318

Copy the model number here:

Copy the serial number here:

CUSTOMERSUPPORT

Please doNOTreturntheunit to the retailer fromwhereit waspurchased,withoutfirstcontactingCustomerSupport.

If you have difficulty assembling this product or have any questions regarding the controls, operation or

maintenance of this unit, you can seek help from the experts. Choose from the options below:

En ine

Visit mtdproducts.com for many useful suggestions. Click on Customer Support button and

you will get the four options reproduced here. Click on the appropriate button and help is

immediately available.

answer you are

looking for could be just

a mouse c//cA awayf

answer are

looking for could be just

a mouse c//cA awayf

If you prefer to reach a Customer Support Representative, please call 1-800-800-7310.

The engine manufacturer is responsible for all engine-related issues with regards to

performance, power-rating, specifications, warranty and service. Please refer to the engine

manufacturer's Owner's/Operator's Manual, packed separately with your unit, for more

information.

SECTION1: IMPORTANTSAFEOPERATIONPRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could

endanger the personal safety and/or property of yourself and others. Read and follow all instructions in

this manual before attempting to operate this machine. Failure to comply with these instructions may

result in personal injury. When you see this symbol - heed its warning.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle

components contain or emit chemicals known to State of California to cause cancer

and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this

manual. As with any type of power equipment, carelessness or error on the part of the operator can

result in serious injury. This machine is capable of amputating hands and feet and throwing objects.

Failure to observe the following safety instructions could result in serious injury or death.

Training

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe

place for future and regular reference and for

ordering replacement parts.

2. Be familiar with all controls and their proper

operation. Know how to stop the machine and

disengage them quickly.

3. Never allow children under 14 years old to operate

this machine. Children 14 years old and over should

read and understand the operation instructions and

safety rules in this manual and should be trained

and supervised by a parent.

4. Never allow adults to operate this machine without

proper instruction.

5. Keep bystanders, helpers, pets and children at least

75 feet from the machine while it is in operation.

Stop machine if anyone enters the area.

Preparation

1. Thoroughly inspect the area where the equipment is

to be used. Remove all stones, sticks, wire, and

other foreign objects which could be tripped over

and cause personal injury.

2. Wear sturdy, rough-soled work shoes and close

fitting slacks and shirt. Loose fitting clothes or

jewelry can be caught in movable parts. Never

operate this machine in bare feet or sandals.

3. Disengage clutch levers and shift (if provided) into

neutral CN") before starting the engine.

4. Never leave this machine unattended with the

engine running.

5. Never attempt to make any adjustments while

engine is running, except where specifically

recommended in the operator's manual.

6. To avoid personal injury or property damage use

extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is

spilled on yourself or your clothes which can ignite.

Wash your skin and change clothes immediately.

7. Use only an approved gasoline container.

8. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

9. Never fuel machine indoors.

10. Never remove gas cap or add fuel while the engine

is hot or running.

11. Allow engine to cool at least two minutes before

refueling.

12. Never over fill fuel tank. Fill tank to no more than ½

inch below bottom of filler neck to provide space for

fuel expansion.

13. Replace gasoline cap and tighten securely.

14. If gasoline is spilled, wipe it offthe engine and

equipment. Move machine to another area. Wait 5

minutes before starting the engine.

15. Never store the machine or fuel container inside

near an open flame, spark or pilot light (e.g.

furnace, water or space heater, clothes dryer etc.).

16. Allow machine to cool 5 minutes before storing.

Operation

1. Do not put hands or feet near rotating parts. Contact

with the rotating parts can amputate hands and feet.

2. Do not operate machine while under the influence

of alcohol or drugs.

3. Never operate this machine without good visibility

or light. Always be sure of your footing and keep a

firm hold on the handles.

4. Keep bystanders, helpers, pets, and children at

least 75 feet from the machine while it is in

operation. Stop the machine if anyone enters the

area.

5. Be careful when tilling in hard ground. The tines

may catch in the ground and propel the tiller

forward. If this occurs, let go of the handle bars and

do not restrain the machine.

6. Exercise extreme caution when operating on or

crossing gravel surfaces. Stay alert for hidden

hazards or traffic. Do not carry passengers.

7. Neveroperatethemachineathightransport

speedsonhardorslipperysurfaces.

8. Exercisecautiontoavoidslippingorfalling.

9. Lookdownandbehindandusecarewhenin

reverseorpullingmachinetowardsyou.

10. Starttheengineaccordingtotheinstructionsfound

inthismanualandkeepfeetwellawayfromthe

tinesatalltimes.

11. Afterstrikingaforeignobject,stoptheengine,

disconnectthesparkplugwireandgroundagainst

theengine.Thoroughlyinspectthemachineforany

damage.Repairthedamagebeforestartingand

operating.

12. Disengageallclutchleversandstopenginebefore

youleavetheoperatingposition(behindthe

handles).Waituntilthetinescometoacomplete

stopbeforeuncloggingthetines,makingany

adjustments,orinspections.

13. Neverrunanengineindoorsorinapoorly

ventilatedarea.Engineexhaustcontainscarbon

monoxide,anodorlessanddeadlygas.

14. Mufflerandenginebecomehotandcancausea

burn.Donottouch.

15. Usecautionwhentillingnearfences,buildingsand

undergroundutilities.Rotatingtinescancause

propertydamageorpersonalinjury.

16. Donotoverloadmachinecapacitybyattemptingto

tillsoiltodeepattofastofarate.

17. Ifthemachineshouldstartmakinganunusualnoise

orvibration,stoptheengine,disconnectthespark

plugwireandgrounditagainsttheengine.Inspect

thoroughlyfordamage.Repairanydamagebefore

startingandoperating.

18. Keepallshields,guardsandsafetydevicesinplace

andoperatingproperly.

19. Neverpickuporcarrymachinewhiletheengineis

running.

20. Useonlyattachmentsandaccessoriesapprovedby

themanufacturer.Failuretodoso,canresultin

personalinjury.

21. Ifsituationsoccurwhicharenotcoveredinthis

manual,usecareandgoodjudgment.Contactyour

dealerortelephone1-800-800-7310forassistance

andthenameofyournearestservicingdealer.

Maintenance& Storage

1. Never tamper with safety devices. Check their

proper operation regularly.

2. Check bolts and screws for proper tightness at

frequent intervals to keep the machine in safe

working condition. Also, visually inspect machine for

any damage.

3. Before cleaning, repairing, or inspecting, stop the

engine and make certain the tines and all moving

parts have stopped. Disconnect the spark plug wire

and ground it against the engine to prevent

unintended starting.

10.

Do not change the engine governor settings or

over-speed the engine. The governor controls the

maximum safe operating speed of the engine.

Maintain or replace safety and instruction labels, as

necessary.

Follow this manual for safe loading, unloading,

transporting, and storage of this machine.

Never store the machine or fuel container inside

where there is an open flame, spark or pilot light

such as a water heater, furnace, clothes dryer etc.

Always refer to the operator's manual for proper

instructions on off-season storage.

If the fuel tank has to be drained, do this outdoors.

Observe proper disposal laws and regulations for

gas, oil, etc. to protect the environment.

YourResponsibility

1. Restrict the use of this power machine to persons

who read, understand and follow the warnings and

instructions in this manual and on the machine.

2. The safety label on the tiller is reproduced below for

your review. To ensure safe operation of the tiller,

follow the instructions on all labels closely.

SECTION2: ASSEMBLINGYOURTILLER

NOTE: This operator's manual covers various models

of tillers. The units illustrated may vary slightly from

your unit. Follow only those instructions which pertain

to your model number.

NOTE: References to right or left side of the tiller are

determined from behind the unit in the operating

position.

ToRemoveUnitFromCarton

• Remove staples, break glue on top flaps, or cut

tape at carton end and peel along top flap to open

carton.

• Remove loose parts included with unit (i.e.,

operator's manual, etc.).

• Cut corners and lay carton down flat.

• Remove packing material.

• Roll or slide unit out of carton. Check carton

thoroughly for loose parts.

• Extend control cable and lay on the floor. Be careful

not to bend or kink control cable.

IMPORTANT: This unit is shipped without gasoline or oil

in the engine. Be certain to service engine with gasoline

and oil as instructed in the separate engine manual

before operating your machine.

LoosePartsIn Carton

Depth Stake

Handle Assembly

Shift Rod

Handle Adjustment Rod (Model series 420 only)

NOTE: All hardware needed for assembly is attached

to the loose parts or the tiller.

BeforeAssembly

WARNING: Disconnect the spark plug wire

and ground it against the engine to prevent

unintended starting.

AttachingDepthStake

• Tip the tiller forward so it rests on front

counterweight.

• Unthread the "T" knob from the top of the depth

stake and remove the flat washer and hex bolt.

Remove the hairpin clip from the clevis pin.

See Figure 1.

• Raise the tine shield hinge flap assembly and insert

the depth stake assembly in the slot (under the tine

shield) and up through the tine shield assembly.

• Insert clevis pin through the tine shield and depth

stake assemblies. Secure with hairpin clip.

Insert hex bolt into the top hole of the depth stake

assembly. Place flat washer on the hex bolt and

thread "T" knob onto the hex bolt. Tighten securely.

See Figure 1.

Tip the tiller back down so it rests on the tines.

Clevis Pin

Depth Stake

Flat Washer Hex Bolt

T-Knob

rpin Clip

Figure 1

AttachingHandleAssembly

• Remove the handle adjustment crank, flange nut,

retainer bracket, shoulder bolt, and lock nut from

the pivot bracket.

• Place the handle assembly in position in the handle

pivot bracket lining the upper holes in the handle

with the slots in the pivot bracket. See Figure 2.

Retainer Bracket,

Shoulder Bolt, & Lock Nut

Handle Adjustment Crank j

and Flange Nut_ /

Pivot Bracket

Figure 2

Lift up the handle assembly and align the bottom

holes in the handle assembly with the holes in the

pivot bracket. Insert shoulder bolt from the left side

of unit through the pivot bracket and the retainer

bracket on the right hand side of the unit.

See Figure 3.

Retainer Bracket

Shoulder Bolt & Lock Nut

Figure 3

•Place the hex opening of the flange nut retainer

bracket over the flange nut securing the handle

adjustment crank and install the lock nut on the

lower shoulder bolt. See Figure 4.

• Pivot handle assembly into position desired.

Tighten the bottom bolt, lock nut, and the handle

adjustment lock securely.

Handle Ad ustment Crank

Retainer Bracket

Gear

Gear Shift Rod

Handle

ustment Rod

(Model Series 420)

Rubber Washer

-lat Washer

Hairpin Clip

Figure 4

AttachingGearShiftRod

NOTE: Model series 420 tiller has two control rods. The

gear shift rod is the longer rod and must be assembled

on the right side on handle.

• Remove the T-handle, hairpin clip, flat washer and

rubber washer from the end of the gear shift rod.

Slide the rod up through the right side of bracket on

the front of the handle assembly. See Figure 5.

• Insert the end of the gear shift rod through the

opening in the top of the shift cover and into the

shift bracket. Secure with rubber washer first, flat

washer, and then hairpin clip. See Figure 5.

• Install the nut and T-handle on the gear shift rod.

Figure 5

AttachingHandleAdjustmentRod

(Model420 seriesonly)

• Remove the T-handle, flange nut, hairpin clip, and

rubber washer from the ends of the handle

adjustment rod. Slide the rod up through the left

side of bracket on the front of the handle assembly.

Refer to Figure 5.

Handle

Adjustment Rod

Positioner

Rubber

Washer

Figure 6

• Slide the rubber washer on the unthreaded end of

the handle adjustment rod and insert the end of the

handle adjustment rod into the positioner bracket

beneath the handle and on top of the tine shield.

Secure with hairpin clip. See Figure 6.

• Reinstall the nut and T-handle.

AttachingClutchCable

• Route the clutch cable underneath the handle and

through the cable clip. Be careful not to bend or

kink the cable. See Figure 7.

Handle Adjustment Crank

Cable

Clip

Figure 7

• Remove one hex nut from the threaded casing on

the end of the cable. Slip the wire up through the

slot on the cable bracket underneath the handle.

• Push the end of the casing up through the cable

bracket. Rethread the hex nut on the end of the

cable. Do not tighten at this time.

Hex Nut

Lock

Washer

Hex

End

Slot in

Cable Bracket

(Viewed From Under Handle)

Figure 8

Pull the cable upwards to obtain slack and hook the

Z end of the cable from right to left into the bracket

on the clutch control (beneath the handle panel).

Tighten the nut against the cable bracket.

See Figure 8.

NOTE: Do not overtighten clutch cable, since too much

tension may cause it to break.

FinalClutchAdjustment

IMPORTANT:Service the engine with oil and gasoline

before checking this adjustment. Refer to the separate

engine manual packed with your tiller.

Position the tiller so the front counterweight is

against a solid object, such as a wall. With the gear

selection lever in NEUTRAL, start the engine. Refer

to Operation section.

NOTE: Keep hands out of belt area while unit is

operating.

• Standing on the right side of the tiller, visually

examine the belt (inside the belt cover). It should

not be turning.

•If the belt turns with the unit in neutral, adjust by

moving the hex nut below the cable bracket down a

few turns.Tighten the upper hex nut against the

bracket. See Figure 8.

• Now move the shift lever to FORWARD (Wheels

Forward) position. Carefully engage the clutch by

squeezing the clutch handle against the handle.

The wheels should spin.

• If the wheels do not spin with the unit in

forward, adjust by moving the hex nut which is

above the cable bracket up a few turns. Tighten the

bottom hex nut against the bracket.

Recheck both adjustments, and readjust as necessary.

Make certain hex nuts at cable bracket are tight (do not

overtighten clutch cable).

NOTE: If additional adjustment is required, it may be

necessary to remove the belt cover and move the hex

nuts at the other end of the clutch cable to increase belt

tension.

Tire Pressure

The tires on your unit may be over-inflated for shipping

purposes. Reduce the tire pressure before operating

the unit. Recommended operating tire pressure is

approximately 14 p.s.i, on 14 inch tires and 20 p.s.i, on

16 inch tires.(Check sidewall of tire for tire

manufacturer's recommended pressure).

WARNING: Maximum tire pressure under

any circumstances is 30 p.s.i. Equal tire

pressure should be maintained on both

tires.

SECTION3: KNOWYOURTILLER

Gear Selection __ Clutch

Handle "_......__ Gear Shift Rod

Handle

Adjustment Cran

Stake

\Handle

Adjustment Rod

Model 420 Series

Model 410 Series

Figure 9

_, WARNING: Read, understand, and follow

all instructions and warnings on the

machine and in this manual before

operating.

Reverse

Reverse wheel drive only.

Neutral

Transmission is in neutral.

GearSelectionHandle

The gear selection handle is located on the front of the

handle assembly (right handle on Model 420 Series). It

is used to select NEUTRAL, REVERSE, orone of the

FORWARD modes.

This tiller is designed for the gear selection handle to be

moved while the engine is running. (It will be difficult to

obtain all four positions with the engine off.) Pull or push

the handle so that the indicator on top of shift cover

points to the area of the operating mode desired.

See Figure 9.

NOTE: If difficulty is encountered in moving the gear

selection handle, refer to the following helpful hints:

•To shift into forward or reverse wheel drive, move

tiller forward slightly then backward to allow the

gears to synchronize.

• To shift into forward wheels and tine drive, push

forward slightly on the gear selection handle and

slowly engage the clutch handle allowing the gears

to synchronize.

• To stop forward movement and tine drive, release

the clutch handle. Do not shift gears with the clutch

handle engaged except when engaging the tines.

Wheels Forward

Forward wheel drive only.

Tines Reverse

Forward wheel drive and reverse tine drive.

,_ WARNING: Make certain unit

NEUTRAL when starting the engine.

is in

ClutchHandle

The clutch handle is located beneath the handle.

Squeezing the clutch handle against the handle

engages the wheel and tine drive mechanisms.

See Figure 9.

ThrottleControl

The throttle control lever is located on the engine. It

controls the engine speed and stops the engine.

ChokeLever(If Equipped)

The choke lever is located by the throttle. It is used to

enrich the fuel mixture in the carburetor when starting a

cold engine.

PrimerButton(If Equipped)

The primer button is located behind the air cleaner. It is

used to enrich the fuel mixture in the carburetor when

starting a cold engine.

DepthStake

The depth stake controls the tilling depth. Refer to

"Setting the Depth" in the Operating Section.

HandleAdjustmentCrank

The handle may be adjusted to the height desired.

Loosen the handle height adjustment lock a few turns.

Pivot handle up or down to desired position. Tighten

lock. See Figure 9.

On Model 420 series, the handle may also be adjusted

to be in line with the tiller or swung to the left or right so

the operator is not walking in the freshly tilled soil. To

adjust the handle position from side to side, pull the

handle adjustment handle back, pivot the tiller handle to

desired position and release the handle.

FuelShut-OffValve Equipped)

Make sure the valve is in the On (horizontal) position

when starting the unit. Any time the tiller is not in

operation (i.e., storing, performing maintenance or

adjustment), make sure the valve is in the OFF

(vertical) position.

EngineControls

See the separate engine manual for additional

information and functions of the engine controls.

SECTION4: OPERATINGYOURTILLER

,_ WARNING: Read, understand, and follow

all instructions and warnings on the

machine and in this manual before

operating.

BeforeStarting

GasAndOilFill-Up

Service the engine with gasoline and oil as instructed in

the separate engine manual packed with your tiller.

Read instructions carefully.

WARNING: Use extreme care when

handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

Never fuel machine indoors or while the

engine is hot or running.

StartingEngine

NOTE: When pushing the unit with the engine off, you

will hear a ratcheting sound (gear noise) which is

normal.

_, WARNING: Be sure no one is standing in

front of the tiller while the engine is

running or being started.

• Place gear selection lever in NEUTRAL.

• Place the throttle control lever in FAST position or if

equipped, place the engine speed control in the

START position.

• Move choke lever to CHOKE position or, if

equipped, push primer two (2) or three (3) times.

Wait about two (2) seconds between each push.

NOTE: A warm engine may not require choking or to be

primed.

• Stand at side of tiller. Grasp the starter handle and

pull out slowly, until it pulls slightly harder. Let rope

rewind slowly.

• Pull starter handle rapidly. Do not allow handle to

snap back. Allow it to rewind slowly while keeping a

firm hold on the starter handle.

• Repeat previous steps until engine starts.

• As engine warms up and begins to operate evenly,

move choke lever gradually to RUN position. If

engine falters, return to choke position, then slowly

move to RUN position.

NOTE: See your engine manual packed with your unit

for more detailed instructions.

NOTE: After starting and prior to using the tiller for the

first time, be certain to check the clutch adjustment as

described in "Checking the Clutch Adjustment" section

of the Assembly Instructions.

ToStopEngine

• Move throttle control to STOP or OFF position.

• Disconnect spark plug wire and ground to prevent

accidentally starting while equipment is

unattended.

NOTE: After the first ten hours of operation, recheck

the clutch adjustment. Refer to final clutch adjustment

in Assembly Instructions.

SettingTheDepth

Tilling depth is controlled by the depth stake which can

be adjusted to five different settings. Adjust the side

shields as you adjust the depth stake.

WARNING: Be certain spark plug wire is

disconnected and grounded against the

engine when performing any adjustments.

•When using the tiller for the first time, use the

second adjustment hole from the top (1" of tilling

depth). See Figure 10.

Use This Position _

First _ort Position

Clevis Pin

Use This Hole For

Lowest (Shallowest)

Position

-----Use This Hole For

Highest (Deepest)

Position

Figure 10

• When breaking up sod and for shallow cultivation,

use the setting which gives 1" of tilling depth

(second hole from the top). Place the side shields in

their lowest position.

• For further depth, raise the depth stake and side

shields and also make one or two more passes

over the area.

• When tilling loose soil, the depth stake may be

raised to its highest position (use bottom

adjustment hole) to give the deepest tilling depth.

Raise the side shields to their highest position.

• To transport tiller, lower the depth stake (use top

adjustment hole).

To adjust the depth stake, remove the clevis pin and

hairpin clip. Move the depth stake to the desired setting

and secure with the clevis pin and hairpin clip.

See Figure 10.

To adjust the side shields, remove the wing nuts. Move

the side shield to the desired position and replace the

wing nuts. Tighten securely.

OperatingtheTiller

• Select the depth stake setting.

• Start engine as instructed on the previous page.

• Move gear selection handle to one of the forward

modes or reverse.

WARNING: Do not move the gear selection

handle with the wheels or tines engaged.

Make certain the unit is stopped

completely before changing the gear

selection. A partial engagement may be

necessary when engaging tines.

• Squeeze the clutch handle against the handle to

engage the wheels and tines.

NOTE: Make certain the gear selection indicator is

correctly positioned before engaging the clutch handle.

If it is between gears, the engine will stall.

To transport tiller, do not engage the tines. Select the

wheel drive only.

WARNING: Do not push down on the

handles so that the wheels are lifted offthe

ground while using the tine drive, or the

tiller could move backward and cause

personal injury.

For best results, it is recommended the garden be tilled

twice (lengthwise, then widthwise) to pulverize the soil.

SECTION5: MAKINGADJUSTMENTS

,_ WARNING: Never attempt to make any

adjustments while the engine is running,

except where specified in operator's

manual.

HandleAdjustment

The handle may be adjusted to the height desired and

on Model 420 series, the handle may also be adjusted

to be in line with the tiller or swung to the left or right.

Refer to the handle adjustment in the Know Your Tiller

section for details.

BeltTensionAdjustment

Periodic adjustment of the belt tension may be required

due to normal stretch and wear on the belt. Adjustment

is needed if the tines or wheels seem to hesitate while

turning, but the engine maintains the same speed.

To adjust the tension on the belt, refer to Final Clutch

Adjustment in Assembly Instructions.

EngineAdjustment

Refer to the separate engine manual for engine

adjustment instructions.

SECTION6: MAINTAININGYOURTILLER

,_ WARNING: Disconnect the spark plug wire

and ground it against the engine before

performing any repairs or maintenance.

Engine

Refer to the separate engine manual for engine

maintenance instructions.

Maintain engine oil as instructed in the separate

engine manual packed with your unit. Read and follow

instructions carefully.

Service air cleaner every ten hours under normal

conditions. Clean every hour under extremely dusty

conditions. Poor engine performance and flooding

usually indicates that the air cleaner should be

serviced. To service the air cleaner, refer to the

separate engine manual packed with your unit.

IMPORTANT: Never run your engine without air cleaner

completely assembled.

The spark plug should be cleaned and the gap reset

every 25 hours of engine operation. Spark plug

replacement is recommended at the start of each tiller

season; check engine manual for correct plug type and

gap specification.

Clean the engine regularly with a cloth or brush. Keep

the cooling system (blower housing area) clean to

permit proper air circulation which is essential to engine

performance and life. Be certain to remove all dirt and

combustible debris from muffler area.

Lubrication

Transmission

The transmission is pre-lubricated and sealed at the

factory. It requires no checking unless the transmission

is disassembled. To fill with grease, lay the right half of

the transmission on its side, add 22 ounces of

Benalene 920 grease, and assemble the left half to it.

This grease can be obtained at your nearest authorized

dealer by ordering part number 737-0300.

Clutch Handle

Lubricate the pivot point on the clutch handle and the

cable at least once a season with light oil. The control

must operate freely in both directions.

PivotPoints

Lubricate all pivot points and linkages at least once a

season with light oil.

Tine Shafts

Remove tine assemblies and lubricate the tine shafts at

least once a season.

Wheel Shafts

Remove wheel assemblies and lubricate the axle shafts

at least once a season.

CleaningTineArea

Clean the underside of the tine shield after each use.

The dirt washes off the tines easier if rinsed off

immediately instead of after it dries. Always towel dry

the tiller afterwards and apply a light coat of oil or

silicone to prevent rusting or water damage.

IMPORTANT:Never use a "pressure washer" to clean

your tiller. Water can penetrate tight areas of the tiller

and its chaincase and cause serious damage to the

unit.

Tires

Recommended operating tire pressure is

approximately 14 p.s.i, on 14 inch tires and 20 p.s.i, on

16 inch tires. (Check sidewall of tire for tire

manufacturer's recommended pressure). Maximum tire

pressure under any circumstances is 30 p.s.i. Equal tire

pressure should be maintained on both tires.

When installing a tire to the rim, be certain rim is clean

and free of rust. Lubricate both the tire and rim

generously.

WARNING: Excessive pressure (over 30

p.s.i.) when seating beads may cause tire/

rim assembly to burst with force sufficient

to cause serious injury.

BeltReplacement

Your tiller has been engineered with a belt made of

special material (Kevlar Tensile) for longer life and

better performance. It should not be replaced with an

off-the-shelf belt. Order all belts through you authorized

service dealer.

•Disconnect and ground the spark plug wire against

the engine.

• Remove the belt cover from the left side of the tiller

by removing two torx head screws from the top of

belt cover.

• Remove two hex cap nuts and flat washers from

front side of the belt cover. Remove the hex nut and

flat washer at the back of the cover.

• Remove the belt keeper assembly located behind

the engine pulley by removing two hex bolts and

lock washers. See Figure 11.

• Remove belt and reassemble the new belt. Follow

instructions in reverse order.

NOTE: Upon reassembly, make certain the belt is

routed over the idler pulley and inside of belt keepers by

engine pulley. See Figure 11.

Engine

Pulley Belt Keeper

Hex Bolt

Idler

Figure 11

0ff-Seas0nStorage

If the tiller will not be used for a period longer than 30

days, the following steps should be taken to prepare the

tiller for storage.

• Clean the exterior of engine and the entire tiller

thoroughly. Lubricate the tiller as described in the

lubrication instructions.

• We do not recommend the use of pressure

washers to clean your unit. They may cause

damage to electric components, spindles, pulleys,

bearings or the engine. The use of pressure

washers will result in shortened life and reduce

serviceability.

• Refer to the engine manual for correct engine

storage instructions.

• Wipe tines with oiled rag to prevent rust.

• Store tiller in a clean, dry area. Do not store next to

corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment in

an unventilated or metal storage shed, care should be

taken to rustproof the equipment. Using a light oil or

silicone, coat the equipment and especially any

springs, bearings, and cables.

SECTION7: TROUBLESHOOTINGGUIDE

Possible Cause(s)

Fuel tank empty, or stale fuel.

Trouble

Engine fails to

start

Engine runs

erratic

Engine overheats

Tines do not

engage

Wheels do not

engage

Throttle control lever not in correct starting

position (if so equipped).

Blocked fuel line.

Dirty aircteaner.

Choke not in ON position.

Spark plug wire disconnected.

Faulty spark plug.

Engine flooded.

Unit running on CHOKE.

Spark plug wire loose.

Blocked fuel line or stale fuel.

Vent in gas cap plugged.

Water or dirt in fuel system.

Dirty air cleaner.

Carburetor out of adjustment.

Engine oil level tow.

Dirty air cleaner.

Air flow restricted.

Carburetor not adjusted properly.

Foreign object lodged in tines.

Tine clevis pin(s) missing.

Pulley and idler not in correct

adjustment.

Not shifting properly.

Control cable not adjusted properly.

Belt worn and/or stretched.

Clevis pin missing.

Tiller is not being shifted properly.

Control cable not adjusted properly.

Belt worn and/or stretched.

Corrective Action

Fill tank with clean, fresh gasoline. Fuel will not last over thirty

days unless a fuel stabilizer is used.

Move throttle lever to start position.

Clean fuel line.

Refer to the engine manual packed with your unit.

Move choke to ON position.

Connect wire to spark plug.

Clean, adjust gap or replace.

Refer to the engine manual packed with your unit.

Move choke lever to OFF position.

Connect and tighten spark plug wire.

Clean fuel line; fill tank with clean, fresh gasoline. Fuel will not

last over thirty days unless a fuel stabilizer is used.

Clear vent.

Drain fuel tank. Refill with fresh fuel.

Refer to the engine manual packed with your unit.

Fill crankcase with proper oil.

Refer to the engine manual packed with your unit.

Adjust carburetor as instructed in separate engine manual.

Dislodge foreign object.

Replace tine clevis pin(s).

Take unit to authorized service dealer.

Refer to controls section of operator's manual for proper

shifting procedures.

Adjust control cable (see assembly instructions).

Replace belt.

Replace clevis pin.

Refer to controls section of operator's manual for proper

shifting procedures.

Adjust control cable (see assembly instructions).

Replace belt.

NOTE: For repairs beyond the minor adjustments above, contact your local authorized service dealer.

SECTION8: PARTSLISTFORMODELSERIES410THRU420

4 i 2\\

\\I

[

26 3,

ModelSeries410thru420

Ref. Part No.

No.

1. 710-1017

2. 786-0101B

786-0168

3. 686-0095

4. 712-3004A

5. 715-0120

6. 786-0117

7. 710-3008

8. 712-3010

9. 736-0242

10. 710-3180

11. 710-1007

12. 619-0009

13. 642-0015

642-0016

14. 711-0415

15. 714-0149B

16. 634-0240

634-0241

634-0238

634-0239

17. 711-1017

18. 734-1796

734-0808

Part Description

Hex Screw 1/4-20 x.625

Shift Cover - Briggs & Stratton

Shift Cover - Tecumseh

Crank Shift Assembly

Hex Lock Nut 5/16-18

Spiral Pin

Shift Cover Mounting Bracket

Hex Cap Screw 5/16-18 x.75

Hex Nut 5/16-18

Bell Washer.340 ID x.872 OD

Hex Cap Screw 5/16-18 x 1.75

Hex Washer Screw 3/8-16 x 1.5

Frame Counterweight

Tine Assembly - LH

Tine Assembly - RH

Clevis Pin

Cotter Pin

Complete Wheel Ass'y - RH (14")

Complete Wheel Ass'y - LH (14")

Complete Wheel Ass'y - RH (16")

Complete Wheel Ass'y - LH (16")

Clevis Pin

Tire Only (14")

Tire Only (16")

Ref.

No.

19.

21.

22.

23.

24.

25.

26.

27.

28.

29.

30.

31.

32.

33.

34.

35.

36.

37.

38.

39.

40.

41.

42.

43.

Part No.

714-0104

710-1090

686-0031A

736-0119

710-0237

756-0971

756-0972

754-0438

756-0405

738-0899

736-0256

756-0634

736-0105

712-0379

736-0452

710-0152

786-0080

710-0723

738-0876

736-3020

786-0100

712-0392

786-0107

686-0094

Part Description

Cotter Pin

Flange Screw 5/16-18 x 1.25

Belt Keeper Bracket Ass'y

Lock Washer 5/16

Hex Cap Screw 5/16-24 x.625

Inner Pulley Half

Outer Pulley Half

V-Belt

Flat Idler

Bolt 5/16-18 x 1/4-28 x 2.35

Flat Washer.635 ID x.930 OD

Flat Pulley

Spring Washer.401 ID x.870 OD

Flange Lock Nut 3/8-24

Bell Washer.396 ID x 1.140 OD

Hex Cap Screw 3/8-24 x 1.0

Idler Bracket

Hex Cap Screw 3/8-16 x 1.25

Shoulder Nut 7/16-20

Flat Washer.271 ID x.630 OD

Belt Cover

Hex Lock Nut 1/4

Cable Bracket

Gear Case Assembly

IMPORTANT: For a proper working machine, use Factory

Approved Parts.

V-BELTS are specially designed to engage and disengage

safely. A substitute (non OEM) V-Belt can be dangerous by not

disengaging completely.

ModelSeries410thru420

Ref. Part No.

No.

1. 721-0378

2. 712-0378

3. 736-0407

4. 721-0379

5. 716-0865

6. 686-0038

7. 618-0245B

9. 713-0233

10. 750-0570

11. 736-0163

12. 750-0936

13. 736-0518

14. 617-0004

15. 736-0351

16. 750-0938

17. 717-1458

19. 611-0021

20. 713-0226

21. 738-0885

22. 750-0935

23. 611-0058

24. 686-0039

25. 710-0896

26. 726-0331

27. 741-0563

28. 712-3067

Part Description

Shaft Seal 1.0 Dia

Hex Nut 7/16-20

Belt Washer.45 ID x 1.00D

Shaft Seal.75 Dia

Snap Ring.50 Dia

Gear Case Assembly - RH Half

Shift Assembly

Chain - #41 1/2" Pitch x 30 Links

Space 1.0 ID x 2.00D

Thrust Washer 1.03 ID x 1.62 OD

Spacer.635 ID x 1.00D

Thrust Washer.445 ID x 1.92 OD

Idler Gear Assembly

Flat Washer.760 ID x 1.50 OD

Spacer.735 ID x.886 OD

Spur Gear 46T

Tine Shaft Assembly 18T

Chain - #50 5/8" Pitch x 52 Links

Jack Shaft 5/8 Dia. X. 2.06 Lg

Spacer.635 ID x 1.00D

Wheel Shift Assembly

Gear Case Assembly - LH Half

Hex Washer Screw 1/4-14 x.625

Plug

Ball Bearing w/Snap Ring

Hex Patch L-Nut 7/16-20

Ref.

No.

29.

30.

31.

32.

33.

34.

35.

36.

37.

38.

39.

40.

41.

42.

43.

44.

45.

46.

47.

48.

49.

50.

51.

52.

53.

Part No.

786-0086

721-0295

710-0258

736-0329

736-0512

741-0124

736-0541

717-1451A

713-0435

736-0265

716-0235

718-0237

711-1087

732-0863

741-0862

718-0234

717-1409

736-0442

732-0614

736-0518

611-0016

738-0884

736-0336

750-0931

617-0003

Part Description

Reinforcement Bracket

Chain Case Gasket

Hex Cap Screw 1/4-20 x.625

Lock Washer 1/4

Flat Washer.281 ID x.875 OD

Ball Bearing

Flat Washer

Spur Gear 16T

Sprocket 11T #41 Chain

Flat Washer.88 ID x 1.50 OD

Retainer Ring

Clutch Key

Drive Shaft

Compression Spring

Detent Ball

Clutch Collar

Spur Gear 17T

Flat Washer.69 ID x 1.06 OD

Wire Ring

Thrust Washer.445 ID x 1.90D

Intermediate Gear Assembly

Jack Shaft

Flat Washer.625 ID x 1.00D

Spacer.635 ID x.86 OD

Tine Drive Assembly

ModelSeries410

10_

-7

J j

J j _ J

J J

17 42_

ModelSeries410

Ref, Part No.

No.

1. 710-1017

2. 786-0131

3. 710-0896

4. 720-0278A

5. 735-0246

6. 647-0014

7. 786-0118

8. 786-0098

9. 649-0017

10. 720-0210A

11. 712-3008

12. 726-0330

13. 747-0902

14. 735-0127

15. 714-0104

16. 736-0204

17. 712-3004A

18. 784-0191

19. 712-0379

20. 750-0885A

21. 784-0190

22. 710-0189

23. 786-0109

24. 786-0108

Ref.

Part Description No. Part No.

Tap Screw 1/4-14 x.625 25. 726-0106

Handle Cover w/o Throttle 26. 747-0432

Hex Washer Screw 1/4-14 x.625 27. 786-0113

Foam Grip 28. 710-3005

End Plug 29. 736-0117

Clutch Control Assembly 30. 710-3008

Return Bracket- LH 31. 738-0849

Return Bracket- RH 32. 786-0085

Handle Assembly 33. 712-0421

Knob 34. 686-0044A

Jam Nut 3/8-16 35. 786-0090

Cable Clip 36. 786-0076

Shift Control 37. 710-0376

Rubber Washer.33 ID x.87 OD 38. 736-0169

Cotter Pin 39. 711-0415

Flat Washer.344 ID x.62 OD 40. 712-0798

Hex Flange Lock Nut 5/16-18 41. 710-3038

Retainer Bracket 42. 686-0043A

Flange Lock Nut 3/8-24 43. 786-0120

Spacer.322 ID x.625 OD 44. 786-0077

Handle Adjustment Crank 45. 710-3097

Hex Screw 5/16-18 x 3.0 46. 714-0147

Handle Mounting Bracket- LH 47. 746-0916

Handle Mounting Bracket- RH

Part Description

Cap Nut

Rod

Rear Tine Shield Flap

Hex Cap Screw 3/8-16 x 1.25

Flat Washer.375 ID x.620 OD

Hex Cap Screw 5/16-18 x.75

Hex Screw 5/16-18 x.75

Tine Shield

Wing Nut

End Cover Assembly

Side Shield

Shield Bracket RH

Hex Cap Screw 5/16-18 x 1.0

Lock Washer 3/8

Clevis Pin

Hex Nut 3/8-16

Hex Cap Screw 5/16-18 x.875

Tine Shield Bracket Assembly

Depth Stake

Shield Bracket- LH

Carriage Bolt 3/8-16 x 1.0

Cotter Pin

Clutch Cable

NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed,

to the part number to order a replacement part. For instance, if a part numbered 700-xxxx is painted Oyster Gray, the part

number to order would be 700-xxxx-0662.

Black -- 0691 ; Black, Powder-- 0637; Blue, Midnight -- 0667; Charcoal -- 0483; Grey -- 0648;

Grey, Oyster -- 0662; Orange -- 0606; Red -- 0650; Red, MTD -- 0638; Silver-- 0629; Yellow -- 0674.

ModelSeries420

4 5

]

Ii ]

]

ModelSeries420

Ref, Part No.

No.

1. 710-1017

2. 786-0131

3. 746-0916

4. 720-0278A

5. 647-0014

6. 735-0246

7. 710-0896

8. 649-0016

9. 786-0118

10. 786-0098

11. 720-0210A

12. 712-3008

13. 747-0902

14. 747-0901

15. 714-3021

16. 712-0386A

17. 736-0317

18. 712-0375

19. 726-0330

20. 732-0493

21. 748-0375

22. 712-0379

23. 784-0191

24. 712-3004A

25. 784-0190

26. 710-0521

27. 710-0189

Ref.

Part Description No. Part No.

Tap Screw 1/4-14 x.625 28. 686-0048

Handle Cover w/o Throttle 29. 710-3097

Clutch Cable 30. 686-0071

Foam Grip 31. 712-0421

Clutch Control Assembly 32. 735-0127

End Plug 33. 736-0204

Hex Washer Screw 1/4-14 x.625 34. 714-0104

Handle Assembly 35. 786-0090

Return Bracket - LH 36. 710-3005

Return Bracket - RH 37. 736-0117

Knob 39. 710-3008

Jam Nut 3/8-16 40. 738-0849

Shift Control 41. 786-0113

Handle Adjustment Rod 42. 786-0085

Cotter Pin 43. 686-0044A

Slotted Hex Nut 5/8 44. 747-0432

Bell Washer.64 ID x 1.25 OD 45. 726-0106

Hex Lock Nut 3/8-16 46. 786-0076

Cable Clip 47. 786-0077

Torsion Spring 48. 710-0376

Handle Swing Link 49. 714-0147

Flange Lock Nut 3/8-24 50. 711-0415

Retainer Bracket 51. 686-0043A

Hex Flange Lock Nut 5/16-18 52. 710-3038

Handle Adjustment Crank 53. 712-0798

Hex Cap Screw 3/8-16 x 3.0 54. 736-0169

Hex Cap Screw 5/16-18 x 3.0 55. 786-0120

Part Description

Handle Pivot Bracket Assembly

Carriage Bolt 3/8-16 x 1.0

Handle Bracket Assembly

Wing Nut

Rubber Washer.33 ID x.87 OD

Flat Washer.344 ID x.62 OD

Cotter Pin

Side Shield

Hex Cap Screw 3/8-16 x 1.25

Flat Washer.375 ID x.620 OD

Hex Cap Screw 5/16-18 x.75

Hex Screw 5/16-18 x.75

Rear Tine Shield Flap

Tine Shield

End Cover Assembly

Rod

Cap Nut

Shield Bracket RH

Shield Bracket - LH

Hex Cap Screw 5/16-18 x 1.0

Cotter Pin

Clevis Pin

Shield Tine Bracket Assembly

Hex Cap Screw 5/16-18 x.875

Hex Nut 3/8-16

Lock Washer 3/8

Depth Stake

NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed,

to the part number to order a replacement part. For instance, if a part numbered 700-xxxx is painted Oyster Gray, the part

number to order would be 700-xxxx-0662.

Black -- 0691 ; Black, Powder -- 0637; Blue, Midnight -- 0667; Charcoal -- 0483; Grey -- 0648;

Grey, Oyster -- 0662; Orange -- 0606; Red -- 0650; Red, MTD -- 0638; Silver -- 0629; Yellow -- 0674.

NOTES

MANUFACTURER'S LIMITED WARRANTY FOR:

The limited warranty set forth below is given by MTD LLC with

respect to new merchandise purchased and used in the

United States, its possessions and territories.

"MTD"warrants this product against defects in material and

workmanship for a period of two (2) years commencing on the

date of original purchase and wilt, at its option, repair or

replace, free of charge, any part found to be defective in

materials or workmanship. This limited warranty shall only

apply if this product has been operated and maintained in

accordance with the Operator's Manual furnished with the

product, and has not been subject to misuse, abuse,

commercial use, neglect, accident, improper maintenance,

alteration, vandalism, theft, fire, water, or damage because of

other peril or natural disaster. Damage resulting from the

installation or use of any part, accessory or attachment not

approved by MTD for use with the product(s) covered by this

manual will void your warranty as to any resulting damage.

Normal wear parts are warranted to be free from defects in

material and workmanship for a period of thirty (30) days from

the date of purchase. Normal wear parts include, but not

limited to items such as: batteries, belts, blades, blade

adapters, grass bags, rider deck wheels, seats, snow thrower

skid shoes, shave plates, auger spiral rubber and tires.

HOW TO OBTAIN SERVICE: Warranty service is available,

WITH PROOF OF PURCHASE, through your local authorized

service dealer. To locate the dealer in your area, check your

Yellow Pages, or contact MTD LLC at P.O. Box 361131,

Cleveland, Ohio 44136-0019, or call 1-800-800-7310 or 1-

330-220-4683 or tog on to our Web site at

www.mtdproducts.com.

This limited warranty does not provide coverage in the

following cases:

The engine or component parts thereof. These items

may carry a separate manufacturer's warranty. Refer

to applicable manufacturer's warranty for terms and

conditions.

Log splitter pumps, valves, and cylinders have a

separate one year warranty.

Routine maintenance items such as lubricants, filters,

blade sharpening, tune-ups, brake adjustments, clutch

adjustments, deck adjustments, and normal

deterioration of the exterior finish due to use or

exposure.

Service completed by someone other than an

authorized service dealer.

MTD does not extend any warranty for products sold or

exported outside of the United States, its possessions

and territories, except those sold through MTD's

authorized channels of export distribution.

Replacement parts that are not genuine MTD parts.

Transportation charges and service calls.

No implied warranty, including any implied warranty of

merchantability of fitness for a particular purpose,

applies after the applicable period of express written

warranty above as to the parts as identified. No other

express warranty, whether written or oral, except as

mentioned above, given by any person or entity,

including a dealer or retailer, with respect to any product,

shall bind MTD. During the period of the warranty, the

exclusive remedy is repair or replacement of the product

as set forth above.

The provisions as set forth in this warranty provide the

sole and exclusive remedy arising from the sale. MTD

shall not be liable for incidental or consequential loss or

damage including, without limitation, expenses incurred

for substitute or replacement lawn care services or for

rental expenses to temporarily replace a warranted

product.

Some states do not allow the exclusion or limitation of

incidental or consequential damages, or limitations on how

long an implied warranty lasts, so the above exclusions or

limitations may not apply to you.

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold. Alteration

of safety features of the product shall void this warranty.

You assume the risk and liability for toss, damage, or injury to

you and your property and/or to others and their property

arising out of the misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the

original purchaser or to the person for whom it was purchased

as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This

limited warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

IMPORTANT: Owner must present Original Proof of

Purchase to obtain warranty coverage.

MTD LLC, P.O.BOX361131CLEVELAND,OHIO44136-0019; Phone:1-800-800-7310,1-330-220-4683

MTD 21AA412A700 User Manual REAR TINE TILLER Manuals And Guides 1109109L

410 Thru 420 1109109L

Navigation menu

Versions of this User Manual:

Views

Navigation