Makita RP0900 Manual User To The 0976b505 9f8b 44a2 Ace3 Fc1125956a1b

User Manual: Makita RP0900 to the manual

Open the PDF directly: View PDF .
Page Count: 12

ENGLISH (Original instructions)

INSTRUCTION MANUAL

DOUBLE INSULATION

IMPORTANT: Read Before Using.

Router

RP0900

009743

ENGLISH (Original instructions)

SPECIFICATIONS

Model RP0900

Collet chuck capacity 6mm, 1/4", 8 mm and/or 3/8"

Plunge capacity 0 - 35 mm

No load speed (min-1) 27,000

Overall height 217 mm

Net weight 2.7 kg

Safety class /II

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

END201-5

Symbols

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

･ Read instruction manual.

･ DOUBLE INSULATION

･ Only for EU countries

Do not dispose of electric equipment

together with household waste

material!

In observance of European Directive

2002/96/EC on waste electric and

electronic equipment and its

implementation in accordance with

national law, electric equipment that

have reached the end of their life must

be collected separately and returned to

an environmentally compatible

recycling facility.

ENE010-1

Intended use

The tool is intended for flush trimming and profiling of

wood, plastic and similar materials.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and

can only be operated on single-phase AC supply. They

are double-insulated and can, therefore, also be used

from sockets without earth wire.

ENG905-1

Noise

The typical A-weighted noise level determined

according to EN60745:

Sound pressure level (LpA) : 89 dB(A)

Sound power level (LWA) : 100 dB(A)

Uncertainty (K) : 3 dB(A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum)

determined according to EN60745:

Work mode : cutting grooves in MDF

Vibration emission (ah) : 4.0 m/s2

Uncertainty (K) : 1.5 m/s2

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test

method and may be used for comparing one tool

with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the

power tool can differ from the declared emission

value depending on the ways in which the tool is

used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of

exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it

is running idle in addition to the trigger time).

ENH101-16

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machine(s):

Designation of Machine:

Router

Model No./ Type: RP0900

are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following

standards or standardised documents:

EN60745

The technical documentation is kept by:

Makita International Europe Ltd.

Technical Department,

Michigan Drive, Tongwell,

Milton Keynes, Bucks MK15 8JD, England

30.1.2009

000230

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, 446-8502, JAPAN

GEA005-3

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

10. Use of power supply via a RCD with a rated

residual current of 30mA or less is always

recommended.

Personal safety

11. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

12. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

13. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your finger on the switch or energising power

tools that have the switch on invites accidents.

14. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

15. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

16.

Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts.

Loose clothes, jewellery

or long hair can be caught in moving parts.

17. If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce dust-

related hazards.

Power tool use and care

18. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

19. Do not use the power tool if the switch does

not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous

and must be repaired.

20. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

21. Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

22.

Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use.

Many accidents

are caused by poorly maintained power tools.

23. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

24. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

Service

25. Have your power tool serviced by a qualified

repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

26. Follow instruction for lubricating and

changing accessories.

27. Keep handles dry, clean and free from oil and

grease.

GEB018-4

ROUTER SAFETY WARNINGS

1. Hold power tool by insulated gripping

surfaces, because the cutter may contact its

own cord. Cutting a "live" wire may make

exposed metal parts of the power tool "live" and

shock the operator.

2. Use clamps or another practical way to secure

and support the workpiece to a stable

platform. Holding the work by your hand or

against the body leaves it unstable and may lead

to loss of control.

3. Wear hearing protection during extended

period of operation.

4. Handle the bits very carefully.

5. Check the bit carefully for cracks or damage

before operation. Replace cracked or

damaged bit immediately.

6. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

7. Hold the tool firmly with both hands.

8. Keep hands away from rotating parts.

9. Make sure the bit is not contacting the

workpiece before the switch is turned on.

10. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate improperly

installed bit.

11. Be careful of the bit rotating direction and the

feed direction.

12. Do not leave the tool running. Operate the tool

only when hand-held.

13. Always switch off and wait for the bit to come

to a complete stop before removing the tool

from workpiece.

14. Do not touch the bit immediately after

operation; it may be extremely hot and could

burn your skin.

15. Do not smear the tool base carelessly with

thinner, gasoline, oil or the like. They may

cause cracks in the tool base.

16. Use bits of the correct shank diameter

suitable for the speed of the tool.

17. Some material contains chemicals which may

be toxic. Take caution to prevent dust

inhalation and skin contact. Follow material

supplier safety data.

18. Always use the correct dust mask/respirator

for the material and application you are

working with.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function

on the tool.

Adjusting the depth of cut

009744

Place the tool on a flat surface. Loosen the screw

securing the stopper pole.

Loosen the lock lever and lower the tool body until the

bit just touches the flat surface. Tighten the lock lever to

lock the tool body.

009745

Next, lower the stopper pole until it makes contact with

the adjusting hex bolt. Align the depth pointer with the

"0" graduation.

Raise the stopper pole until the desired depth of cut is

obtained. The depth of cut is indicated on the scale (1

mm per graduation) by the depth pointer. Then tighten

the screw to secure the stopper pole.

Now, your predetermined depth of cut can be obtained

by loosening the lock lever and then lowering the tool

body until the stopper pole makes contact with the

adjusting hex bolt.

009746

CAUTION:

• Since excessive cutting may cause overload of the

motor or difficulty in controlling the tool, the depth

of cut should not be more than 15 mm at a pass

when cutting grooves with an 8 mm diameter bit.

• When cutting grooves with a 20 mm diameter bit,

the depth of cut should not be more than 5 mm at

a pass.

When you wish to cut grooves more than 15 mm

deep with an 8 mm diameter bit or more than 5

mm deep with a 20 mm diameter bit, make several

passes with progressively deeper bit settings.

Stopper block

009746

The stopper block has three adjusting hex bolts which

raise or lower 0.8 mm per turn. You can easily obtain

three different depths of cut using these adjusting hex

bolts without readjusting the stopper pole.

Adjust the lowest hex bolt to obtain the deepest depth of

cut, following the method of "Adjusting depth of cut".

Adjust the two remaining hex bolts to obtain shallower

depths of cut. The differences in height of these hex

bolts are equal to the differences in depths of cut.

To adjust the hex bolts, turn the hex bolts. The stopper

block is also convenient for making three passes with

progressively deeper bit settings when cutting deep

grooves.

CAUTION:

When using a bit having total length of 60 mm or more,

or edge length of 35 mm or more, the depth of cut

cannot be adjusted as previously mentioned. To adjust,

proceed as follows:

Loosen the lock lever and carefully adjust bit protrusion

below the tool base to the desired depth of cut by

moving the tool body up or down. Then retighten the

lock lever to lock the tool body at that depth of cut. Keep

the tool body locked at this position during use. Since

the bit always protrudes from the tool base, be careful

when handling the tool.

1. Depth pointer

2. Screw

3. Stopper pole

4. Adjusting hex

bolt

5. Stopper block

1. Depth pointer

2. Screw

3. Stopper pole

4. Adjusting hex

bolt

5. Stopper block

1. Lock lever

2. Screw

1. Stopper pole

2. Screw

Adjusting the lock lever

009745

The locked position of the lock lever is adjustable. To

adjust it, remove the screw securing the lock lever. The

lock lever will come off. Set the lock lever at the desired

angle. After adjustment, tighten the lock lever clockwise.

Switch action

009747

CAUTION:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and

returns to the "OFF" position when released.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

Installing or removing the bit

009748

CAUTION:

• Install the bit securely. Always use only the

wrenches provided with the tool. A loose or

overtightened bit can be dangerous.

• Do not tighten the collet nut without inserting a bit.

It can lead to breakage of the collet cone.

Insert the bit all the way into the collet cone and tighten

the collet nut securely with the two wrenches.

A 6 mm or 1/4" collet cone is also provided as standard

equipment besides the 8 mm or 3/8" collet cone that is

factory installed on the tool. Use the correct size collet

cone for the bit which you intend to use.

To remove the bit, follow the installation procedure in

reverse.

OPERATION

Set the tool base on the workpiece to be cut without the

bit making any contact. Then turn the tool on and wait

until the bit attains full speed. Lower the tool body and

move the tool forward over the workpiece surface,

keeping the tool base flush and advancing smoothly

until the cutting is complete.

When doing edge cutting, the workpiece surface should

be on the left side of the bit in the feed direction.

001984

NOTE:

• Moving the tool forward too fast may cause a poor

quality of cut, or damage to the bit or motor.

Moving the tool forward too slowly may burn and

mar the cut. The proper feed rate will depend on

the bit size, the kind of workpiece and depth of cut.

Before beginning the cut on the actual workpiece,

it is advisable to make a sample cut on a piece of

scrap lumber. This will show exactly how the cut

will look as well as enable you to check

dimensions.

• When using the straight guide, be sure to install it

on the right side in the feed direction. This will help

to keep it flush with the side of the workpiece.

1. Workpiece

2. Bit revolving direction

3. View from the top of the tool

4. Feed direction

1. Switch trigger

1. Lock lever

2. Screw

001985

Straight guide

009749

The straight guide is effectively used for straight cuts

when chamfering or grooving.

To install the straight guide, insert the guide bars into the

holes in the tool base. Adjust the distance between the

bit and the straight guide. At the desired distance, tighten

the wing bolts to secure the straight guide in place.

123

009750

When cutting, move the tool with the straight guide flush

with the side of the workpiece.

If the distance (A) between the side of the workpiece and

the cutting position is too wide for the straight guide, or if

the side of the workpiece is not straight, the straight guide

cannot be used. In this case, firmly clamp a straight board

to the workpiece and use it as a guide against the router

base. Feed the tool in the direction of the arrow.

009751

Templet guide (Accessory)

009752

The templet guide provides a sleeve through which the

bit passes, allowing use of the tool with templet patterns.

To install the templet guide, loosen the screws on the

tool base, insert the templet guide and then tighten the

screws.

009753

Secure the templet to the workpiece. Place the tool on

the templet and move the tool with the templet guide

sliding along the side of the templet.

003695

NOTE:

• The workpiece will be cut a slightly different size

from the templet. Allow for the distance (X)

between the bit and the outside of the templet

guide. The distance (X) can be calculated by using

the following equation:

Distance (X) = (outside diameter of the templet

guide - bit diameter) / 2

1. Bit

2. Base

3. Templet

4. Workpiece

5. Distance (X)

6. Outside

diameter of the

templet guide

7. Templet guide

1. Screw

2. Base

3. Template guide

1. Guide bar

2. Clamp screw

3. Straight guide

1. Feed direction

2. Bit revolving

direction

3. Workpiece

4. Straight guide

Dust nozzle set (Accessory)

009754

Use the dust nozzle for dust extraction. Install the dust

nozzle on the tool base using the thumb screw so that

protrusion on the dust nozzle fit to the notch in the tool

base.

Then connect a vacuum cleaner to the dust nozzle.

009755

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

• Never use gasoline, benzine, thinner, alcohol or

the like. Discoloration, deformation or cracks may

result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers,

always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Straight & groove forming bits

• Edge forming bits

• Laminate trimming bits

• Straight guide

• Templet guide 25

• Templet guides

• Templet guide adapter

• Lock nut

• Collet cone 3/8", 1/4"

• Collet cone 6 mm, 8 mm

• Wrench 13

• Wrench 22

• Dust nozzle set

1. Dust nozzle

2. Thumb screw

Router bits

Straight bit

005116

DAL 1L 2

1/4"

8 8 60 25

1/4"

650 18

85018

20 50 15

009802

"U"Grooving bit

005117

DAL 1L 2R

6 6 50 18 3

009803

"V"Grooving bit

005118

DAL 1L 2

1/4" 20 50 15

009804

Drill point flush trimming bit

005120

L 1

L 2

L 3

009806

Drill point double flush trimming bit

005121

L 1

L 2

L 3

L 4

009807

Corner rounding bit

005125

A 1

A 2

L 1

L 2

L 3

009808

Chamfering bit

005126

L 1

L 2

L 3

620 49 14 2

009809

Cove beading bit

005129

L 1

L 2

009810

Ball bearing flush trimming bit

005130

DAL 1L 2

1/4"

10 50 20

009811

Ball bearing corner rounding bit

005131

1/4"

A 1

A 2

L 1

L 2

L 3

3.5

009812

Ball bearing chamfering bit

005132

1/4"

A 1

A 2

L 1

L 2

009813

Ball bearing beading bit

005133

D A 1 A 2 A 3 L 1 L 2 L 3 R

5.5 4

4.5

12 726 12 8 42

20 12 8 40

009814

Ball bearing cove beading bit

005134

D A 1 A 2 A 4 L 1 L 2 L 3 R

5.5 3

12 526 22 8 42

20 18 8

A 3

12 40

009815

Ball bearing roman ogee bit

005135

D A 1 A 2 L 1 L 2 L 3 R 1 R 2

2.5 4.5

4.5

4.5 626 8 42 12

20 8 40 10

009816

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Makita Corporation

Anjo, Aichi, Japan

www.makita.com

884875D229

Makita RP0900 Manual User To The 0976b505 9f8b 44a2 Ace3 Fc1125956a1b

Navigation menu

Versions of this User Manual:

Views

Navigation