Makita RP0900 Manual User To The 0976b505 9f8b 44a2 Ace3 Fc1125956a1b

User Manual: Makita RP0900 to the manual

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

ENGLISH (Original instructions)

INSTRUCTION MANUAL

Router
RP0900

009743

DOUBLE INSULATION

IMPORTANT: Read Before Using.

ENGLISH (Original instructions)

SPECIFICATIONS
Model

RP0900

Collet chuck capacity

6mm, 1/4", 8 mm and/or 3/8"

Plunge capacity

0 - 35 mm

No load speed (min-1)

27,000

Overall height

217 mm

Net weight

2.7 kg

Safety class

/II

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END201-5

Wear ear protection

Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
･ Read instruction manual.
･

DOUBLE INSULATION

･

Only for EU countries
Do not dispose of electric equipment
together
with
household
waste
material!
In observance of European Directive
2002/96/EC on waste electric and
electronic
equipment
and
its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an
environmentally
compatible
recycling facility.

ENG900-1

Vibration
The vibration total value (tri-axial
determined according to EN60745:

ENG901-1
•

•

ENE010-1
•

ENF002-2

Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
level

The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH101-16

For European countries only

ENG905-1

noise

sum)

Work mode : cutting grooves in MDF
Vibration emission (ah) : 4.0 m/s2
Uncertainty (K) : 1.5 m/s2

Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.

Noise
The typical A-weighted
according to EN60745:

vector

EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Router
Model No./ Type: RP0900
are of series production and

determined

Sound pressure level (LpA) : 89 dB(A)
Sound power level (LWA) : 100 dB(A)
Uncertainty (K) : 3 dB(A)
2

electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
17. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dustrelated hazards.

Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by:
Makita International Europe Ltd.
Technical Department,
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England

30.1.2009

000230

Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
GEA005-3

General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.

Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
3

Power tool use and care
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
19. Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.
20. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
21. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
22. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
25. Have your power tool serviced by a qualified
repair
person
using
only
identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
26. Follow instruction for lubricating and
changing accessories.
27. Keep handles dry, clean and free from oil and
grease.

3.
4.
5.

6.
7.
8.
9.
10.

11.
12.
13.

14.

15.

16.
17.

18.

SAVE THESE INSTRUCTIONS.
WARNING:

GEB018-4

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.

ROUTER SAFETY WARNINGS
1.

against the body leaves it unstable and may lead
to loss of control.
Wear hearing protection during extended
period of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation. Replace cracked or
damaged bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
Make sure the bit is not contacting the
workpiece before the switch is turned on.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate improperly
installed bit.
Be careful of the bit rotating direction and the
feed direction.
Do not leave the tool running. Operate the tool
only when hand-held.
Always switch off and wait for the bit to come
to a complete stop before removing the tool
from workpiece.
Do not touch the bit immediately after
operation; it may be extremely hot and could
burn your skin.
Do not smear the tool base carelessly with
thinner, gasoline, oil or the like. They may
cause cracks in the tool base.
Use bits of the correct shank diameter
suitable for the speed of the tool.
Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
Always use the correct dust mask/respirator
for the material and application you are
working with.

Hold power tool by insulated gripping
surfaces, because the cutter may contact its
own cord. Cutting a "live" wire may make
exposed metal parts of the power tool "live" and
shock the operator.
Use clamps or another practical way to secure
and support the workpiece to a stable
platform. Holding the work by your hand or
4

FUNCTIONAL DESCRIPTION
•

•

CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting or checking function
on the tool.

•

Adjusting the depth of cut
1. Stopper pole
2. Screw

CAUTION:
Since excessive cutting may cause overload of the
motor or difficulty in controlling the tool, the depth
of cut should not be more than 15 mm at a pass
when cutting grooves with an 8 mm diameter bit.
When cutting grooves with a 20 mm diameter bit,
the depth of cut should not be more than 5 mm at
a pass.
When you wish to cut grooves more than 15 mm
deep with an 8 mm diameter bit or more than 5
mm deep with a 20 mm diameter bit, make several
passes with progressively deeper bit settings.

Stopper block
1

2
009744

Place the tool on a flat surface. Loosen the screw
securing the stopper pole.
Loosen the lock lever and lower the tool body until the
bit just touches the flat surface. Tighten the lock lever to
lock the tool body.

2
3
4
5
009746

The stopper block has three adjusting hex bolts which
raise or lower 0.8 mm per turn. You can easily obtain
three different depths of cut using these adjusting hex
bolts without readjusting the stopper pole.
Adjust the lowest hex bolt to obtain the deepest depth of
cut, following the method of "Adjusting depth of cut".
Adjust the two remaining hex bolts to obtain shallower
depths of cut. The differences in height of these hex
bolts are equal to the differences in depths of cut.
To adjust the hex bolts, turn the hex bolts. The stopper
block is also convenient for making three passes with
progressively deeper bit settings when cutting deep
grooves.

1. Lock lever
2. Screw

1
2
009745

Next, lower the stopper pole until it makes contact with
the adjusting hex bolt. Align the depth pointer with the
"0" graduation.
Raise the stopper pole until the desired depth of cut is
obtained. The depth of cut is indicated on the scale (1
mm per graduation) by the depth pointer. Then tighten
the screw to secure the stopper pole.
Now, your predetermined depth of cut can be obtained
by loosening the lock lever and then lowering the tool
body until the stopper pole makes contact with the
adjusting hex bolt.
1

2
3
4
5

1. Depth pointer
2. Screw
3. Stopper pole
4. Adjusting hex
bolt
5. Stopper block

CAUTION:
When using a bit having total length of 60 mm or more,
or edge length of 35 mm or more, the depth of cut
cannot be adjusted as previously mentioned. To adjust,
proceed as follows:
Loosen the lock lever and carefully adjust bit protrusion
below the tool base to the desired depth of cut by
moving the tool body up or down. Then retighten the
lock lever to lock the tool body at that depth of cut. Keep
the tool body locked at this position during use. Since
the bit always protrudes from the tool base, be careful
when handling the tool.

1. Depth pointer
2. Screw
3. Stopper pole
4. Adjusting hex
bolt
5. Stopper block

009746

Adjusting the lock lever

CAUTION:
Install the bit securely. Always use only the
wrenches provided with the tool. A loose or
overtightened bit can be dangerous.
•
Do not tighten the collet nut without inserting a bit.
It can lead to breakage of the collet cone.
Insert the bit all the way into the collet cone and tighten
the collet nut securely with the two wrenches.
A 6 mm or 1/4" collet cone is also provided as standard
equipment besides the 8 mm or 3/8" collet cone that is
factory installed on the tool. Use the correct size collet
cone for the bit which you intend to use.
To remove the bit, follow the installation procedure in
reverse.
•

1. Lock lever
2. Screw

1
2
009745

The locked position of the lock lever is adjustable. To
adjust it, remove the screw securing the lock lever. The
lock lever will come off. Set the lock lever at the desired
angle. After adjustment, tighten the lock lever clockwise.

OPERATION

Switch action

Set the tool base on the workpiece to be cut without the
bit making any contact. Then turn the tool on and wait
until the bit attains full speed. Lower the tool body and
move the tool forward over the workpiece surface,
keeping the tool base flush and advancing smoothly
until the cutting is complete.
When doing edge cutting, the workpiece surface should
be on the left side of the bit in the feed direction.

1. Switch trigger

1
009747

CAUTION:
Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
•

2
3

ASSEMBLY
•

1. Workpiece
2. Bit revolving direction
3. View from the top of the tool
4. Feed direction

CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.

001984

NOTE:
•
Moving the tool forward too fast may cause a poor
quality of cut, or damage to the bit or motor.
Moving the tool forward too slowly may burn and
mar the cut. The proper feed rate will depend on
the bit size, the kind of workpiece and depth of cut.
Before beginning the cut on the actual workpiece,
it is advisable to make a sample cut on a piece of
scrap lumber. This will show exactly how the cut
will look as well as enable you to check
dimensions.
•
When using the straight guide, be sure to install it
on the right side in the feed direction. This will help
to keep it flush with the side of the workpiece.

Installing or removing the bit

009748

Templet guide (Accessory)

1. Feed direction
2. Bit revolving
direction
3. Workpiece
4. Straight guide

4
001985

Straight guide

009752

The templet guide provides a sleeve through which the
bit passes, allowing use of the tool with templet patterns.
To install the templet guide, loosen the screws on the
tool base, insert the templet guide and then tighten the
screws.
1

1. Screw
2. Base
3. Template guide

009749

The straight guide is effectively used for straight cuts
when chamfering or grooving.
To install the straight guide, insert the guide bars into the
holes in the tool base. Adjust the distance between the
bit and the straight guide. At the desired distance, tighten
the wing bolts to secure the straight guide in place.

3
009753

Secure the templet to the workpiece. Place the tool on
the templet and move the tool with the templet guide
sliding along the side of the templet.

1. Guide bar
2. Clamp screw
3. Straight guide

2
1

3
4

009750

5
6

When cutting, move the tool with the straight guide flush
with the side of the workpiece.
If the distance (A) between the side of the workpiece and
the cutting position is too wide for the straight guide, or if
the side of the workpiece is not straight, the straight guide
cannot be used. In this case, firmly clamp a straight board
to the workpiece and use it as a guide against the router
base. Feed the tool in the direction of the arrow.

1. Bit
2. Base
3. Templet
4. Workpiece
5. Distance (X)
6. Outside
diameter of the
templet guide
7. Templet guide

003695

NOTE:
•
The workpiece will be cut a slightly different size
from the templet. Allow for the distance (X)
between the bit and the outside of the templet
guide. The distance (X) can be calculated by using
the following equation:
Distance (X) = (outside diameter of the templet
guide - bit diameter) / 2

009751

Dust nozzle set (Accessory)

1. Dust nozzle
2. Thumb screw
009754

Use the dust nozzle for dust extraction. Install the dust
nozzle on the tool base using the thumb screw so that
protrusion on the dust nozzle fit to the notch in the tool
base.
Then connect a vacuum cleaner to the dust nozzle.

OPTIONAL ACCESSORIES
CAUTION:
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Straight & groove forming bits
•
Edge forming bits
•
Laminate trimming bits
•
Straight guide
•
Templet guide 25
•
Templet guides
•
Templet guide adapter
•
Lock nut
•
Collet cone 3/8", 1/4"
•
Collet cone 6 mm, 8 mm
•
Wrench 13
•
Wrench 22
•
Dust nozzle set
•

009755

MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
•
Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
•

Drill point flush trimming bit

Router bits
Straight bit

005120

005116

mm
D
6

6
1/4"

1/4"

009806

Drill point double flush trimming bit

009802

"U"Grooving bit

005121

009807

Corner rounding bit

005117

mm
D

009803

"V"Grooving bit

005125

mm
D

009808

005118

mm
D

1/4"

009804

Ball bearing corner rounding bit

Chamfering bit

005126

005131

mm
D

1/4"

3.5

009809

009812

Cove beading bit

Ball bearing chamfering bit

005129

005132

mm
D

D
6
1/4"
6

009810

Ball bearing flush trimming bit

009813

Ball bearing beading bit

005130
005133

mm
D
6
1/4"

009811

mm
R

6
6

20
26

12
12

8
8

40
42

10
12

5.5
4.5

4
7

009814

Ball bearing cove beading bit

005134

mm
R

5.5

009815

Ball bearing roman ogee bit

005135

mm
R2

6
6

20
26

8
8

40
42

10
12

4.5
4.5

2.5
3

4.5
6

009816

NOTE:
•
Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.

Makita Corporation
Anjo, Aichi, Japan

884875D229

12
www.makita.com

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
GTS PDFX Conformance            : PDF/X-1a:2001
GTS PDFX Version                : PDF/X-1:2001
Trapped                         : False
Creator Tool                    : Word 用 Acrobat PDFMaker 7.0.7
Modify Date                     : 2012:07:30 09:26:30+09:00
Create Date                     : 2012:07:24 08:59:32+09:00
Metadata Date                   : 2012:07:30 09:26:30+09:00
Format                          : application/pdf
Title                           : Manual
Creator                         : makita Team
Company                         : nakanippon
Document ID                     : uuid:fcb526ce-525b-443b-9b10-4f3ebb26031e
Instance ID                     : uuid:b753aca0-bc08-4629-bb28-9bf67c7fe54f
Page Count                      : 12
Page Layout                     : OneColumn
Author                          : makita Team

EXIF Metadata provided by EXIF.tools

Makita RP0900 Manual User To The 0976b505 9f8b 44a2 Ace3 Fc1125956a1b

Navigation menu

Versions of this User Manual:

Views

Navigation