45730 BLH 450 X BNF Slipsheet BLH4380A Manual EN
User Manual: Manual Blade 450 X Flybarless 3D RC Helicopter BNF with BeastX Stabilization System | Horizon Hobby
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
® BLH4380A Components Box Contents: • Blade 450 X • 3S 11.1V 2200mAh 30C Li-Po Battery • DC Li-Po Balancing Charger Airframe Blade® 450 X Motor 440H Brushless Outrunner, 4200Kv Spektrum™ AR7200BX with Receiver BeastX® Technology 35-Amp Brushless ESC ESC Swash Servos Digital Cyclic Servo 12 g Metal Gear Digital Tail Servo 12 g Metal Gear Tail Servo 3S 11.1V 2200mAh 30C Li-Po Battery DC Li-Po Balancing Charger Charger To register your product online, visit www.bladehelis.com Transmitter Setup Program your transmitter before attempting to bind or fly the helicopter. Transmitter programming values are shown below for the Spektrum DX6i, DX6, DX7/DX7se, DX7s, DX8, DX9 and DX18. The files for models using Spektrum TM transmitters with AirWare™ software are also available for download online in the Spektrum Community. DX6i SETUP LIST Model Type HELI Reverse Swash Type THRO N AILE N ELEV N 1 Servo 90 Degree RUDD R GYRO N PITC R Gyro Rate SW-F. Mode 77.0% NORM 0 Pos. 0 1 77.0% STUNT 0 NORM STUNT HOLD ADJUST LIST Dual Rate / Expo Switch Pos. D/R Expo 0 100% INH AILE 1 85% INH 0 100% INH ELEV 1 85% INH 0 100% INH RUDD 1 85% INH Timer Type: Down Time: 4:00 Switch: Trainer L 0% 75% 10% Throttle Curve 2 3 30% 60% 75% 75% 10% 10% 4 60% 75% 10% DX7/DX7se SETUP LIST Model Type HELI Pos. 0 Reverse Swash Type THRO N AILE N ELEV N 1 Servo 90 Degree RUDD R GYRO N PITC N Gyro Rate SW-F. Mode 77.0% NORM 0 1 77.0% STUNT 0 Type: Down Time: 4:00 Switch: Trainer Throttle Curve 2 3 4 H 30% 60% 60% 60% NORM 100% 100% 100% 100% STUNT 10% 10% 10% 10% HOLD DX6/DX7s/DX8/DX9/DX18 SETUP LIST Model Type HELI Pos. Rate Reverse Swash Type THRO N AILE N ELEV N 1 Servo 90 Degree RUDD R GYRO N PITC N Gyro SW-F. Mode 0 54.0% NORM 0 1 54.0% STUNT 0 NORM STUNT HOLD Pitch Curve 2 3 40% 50% 25% 50% 25% 50% L 30% 0% 0% Pitch Curve 2 3 40% 50% 25% 50% 25% 50% ADJUST LIST Dual Rate / Expo Switch Pos. D/R Expo 0 100% INH AILE 1 85% INH 0 100% INH ELEV 1 85% INH 0 100% INH RUDD 1 85% INH Timer Type: Down Time: 4:00 Switch: Trainer Throttle Curve L 2 3 NORM 0% 30% 60% STUNT 1 75% 75% 75% STUNT 2 100% 100% 100% HOLD 10% 10% 10% L 30% 0% 0% ADJUST LIST Dual Rate / Expo Switch Pos. D/R Expo 0 100% INH AILE 1 85% INH 0 100% INH ELEV 1 85% INH 0 100% INH RUDD 1 85% INH Timer L NORM 0% STUNT 100% HOLD 10% H 60% 75% 10% 4 60% 75% 100% 10% H 60% NORM 75% STUNT 100% 10% HOLD L 30% Pitch Curve 2 3 40% 50% Travel Adjust THRO AILE ELEV RUDD GYRO PITC 100% 100% 100% 100% 100% 100% Sub-Trim* THRO AILE ELEV RUDD GYRO PITC 0 0* 0* 0* 0 0 Swash Mix 4 75% 75% 75% H 100% 100% 100% Travel Adjust THRO AILE ELEV RUDD GYRO PITC 100% 100% 100% 100% 100% 100% INHIBIT Sub-Trim* THRO AILE ELEV RUDD GYRO PITC 0 0* 0* 0* 0 0 Swash Mix 4 75% 75% 75% H 100% 100% 100% Travel Adjust THRO AILE ELEV RUDD GYRO PITC 100% 100% 100% 100% 100% 100% INHIBIT Sub-Trim* THRO AILE ELEV RUDD GYRO PITC 0 0* 0* 0* 0 0 Swash Mix 4 75% H 100% 0% 25% 50% 75% 100% 0% 25% 50% 75% 100% INHIBIT * Never use sub-trims or trims on AILE, ELEV or RUDD channels with the AR7200BX. Transmitter and Receiver Binding Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum™ DSM2/DSMX technology equipped aircraft transmitter to the receiver for proper operation. Binding Procedure 1. Program your transmitter using the Transmitter Setup found in this manual. 2. Insert the bind plug in the BND/DAT port on the receiver. 3. Connect the flight battery to the ESC. The H menu LED should be flashing, indicating the AR7200BX is in bind mode. 4. Move the throttle stick to the desired failsafe position (low throttle position in normal mode). 5. Follow the procedures of your specific transmitter to enter Bind Mode. The system will connect within a few seconds. Once connected, the H LED will turn off and the AR7200BX will start the initialization process. 6. When the initialization process is complete, the Status LED light will come ON solid BLUE. 7. Disconnect the flight battery and remove the bind plug from the AR7200BX. Store the bind plug in a convenient place. NOTICE: Remove the bind plug to prevent the system from entering bind mode the next time the power is turned on. If you encounter problems, obey binding instructions and refer to transmitter troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support office. For a list of compatible DSM transmitters, please visit www.bindnfly.com. Compliance Information for the European Union Declaration of Conformity Instructions for disposal of WEEE by users in the European Union (in accordance with ISO/IEC 17050-1) No. HH2014070202 Product(s): Blade 450 X BNF Item Number(s): BLH4380A Equipment class: 1 The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE Directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 2006/95/EC: This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product. EN 301 489-1 V1.9.2: 2012 EN 301 489-17 V2.1.1: 2009 EN60950-1:2006+A11:2009+A1:2010+A12: 2011 EN55022:2010 + AC:2011 EN55024:2010 Signed for and on behalf of: Horizon Hobby, LLC. Champaign, IL USA July 2, 2014 Robert Peak Chief Financial Officer Horizon Hobby, LLC
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : ghunt Create Date : 2014:07:14 16:33:25-05:00 Modify Date : 2014:07:14 16:36:29-05:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Producer : Acrobat Distiller 10.0.0 (Macintosh) Format : application/pdf Creator : ghunt Title : 45730 BLH 450 X BNF Slipsheet.indd Creator Tool : Adobe InDesign CS5.5 (7.5.2) Metadata Date : 2014:07:14 16:36:29-05:00 Document ID : uuid:f7ed50ec-2baf-6247-a6d5-655109c38ed4 Instance ID : uuid:5a803741-0ec8-d44d-bc98-4d84ea4173f0 Page Count : 2EXIF Metadata provided by EXIF.tools