Pdf GTB UHD600 HBTL Manual
2018-01-03
: Manual Pdf Gtb-Uhd600-Hbtl Manual pdf_GTB-UHD600-HBTL_manual GTB-UHD600-HBTL products
Open the PDF directly: View PDF 
.
Page Count: 30
| Download | |
| Open PDF In Browser | View PDF |
4K Ultra HD 600 MHz HDBaseT™ Extenders GTB-UHD600-HBT GTB-UHD600-HBTL User Manual Version A2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install or place this product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. To reduce the risk of electric shock and/or damage to this product, never handle or touch this unit or power cord if your hands are wet or damp. Do not expose this product to rain or moisture. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Batteries that may be included with this product and/or accessories should never be exposed to open flame or excessive heat. Always dispose of used batteries according to the instructions. 2 Warranty Information For the latest warranty coverage information, refer to the Warranty and Return Policy under the Connect section of the Gefen website at http://www.gefen.com/connect/warranty-andreturn-policy 3 Contact Us Technical Support 1-707-283-5900 1-800-472-5555 8:00 AM to 5:00 PM Monday - Friday, Pacific Time Email support@gefen.com Web http://www.gefen.com Mailing Address Gefen Core Brands, LLC c/o Customer Service 1800 S McDowell Blvd Petaluma, CA 94954 USA © 2017 Core Brands, LLC. All Rights Reserved. All trademarks are the property of their respective owners. Gefen and Core Brands, LLC reserve the right to make changes in the hardware, packaging, and any accompanying documentation without prior notice. 4 Operating Notes • Important • While Unshielded (UTP) CAT-5e is usually adequate, shielded (STP) CAT-6A is recommended. Shielded (STP) CAT-5e or unshielded (UTP) CAT-5e or CAT6A may be acceptable depending on cable quality. Care should always be given to keep these cables away from power lines and other sources of electromagnetic interference. • Cable quality is critical when handling 600 MHz HDMI signals. We highly recommend 10-foot or shorter Gefen Locking HDMI cables. They have been designed and tested to work at 600 MHz and reliably transport the the full 18.2 Gbps throughput of HDMI 2.0. • The Sender unit has 2 EDID Management DIP Switches on its bottom panel, under a self-adhesive cover. This product is shipped with its DIP switches set to enable 4K with 2-Channel Audio mode (SW1: ON, SW2: OFF). Please see the manual for details before changing the DIP Switch settings. • The GTB-UHD600-HBT and GTB-UHD600-HBTL vary in maximum extension distances, based on resolution / timing and color depth. Refer to the Features section on pages 6 and 7 for more information . • Power Over Line (POL) is a proprietary Gefen implementation that provides power over the link cable. The GTB-UHD600-HBT and GTB-UHD600-HBTL feature Bi-Directional POL, meaning that the power supply (1 pc included) can be connected to either the Sender or the Receiver unit. • The information in this manual has been carefully checked and is believed to be accurate. However, Gefen and Core Brands, LLC assume no responsibility for any inaccuracies that may be contained in this manual. In no event will Gefen and Core Brands, LLC be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect or omission in this manual. • All information contained herein is subject to change without notice. This product uses UL-Listed power supplies 5 Features & Packing List Features (GTB-UHD600-HBT)* • Supports 18.2 Gbps bandwidth and 600 MHz TMDS clock • Extends HDMI, RS-232, & Bi-Directional IR over a single CAT-5e/CAT-6A: • * 4K Ultra HD (3840 x 2160 to 60 Hz, 4:4:4), up to 264 feet/80 meters (8-bit color) * 4K Cinema (DCI) (4096 x 2160 to 60 Hz 4:4:4), up to 264 feet/80 meters (8-bit color) * 1080p Full HD (60 Hz) and WUXGA (1920 x 1200 to 60 Hz), up to 330 feet/100 meters (up to 12-bit Deep Color) HDMI Features Supported: * HDMI 2.0 (full bandwidth to 18.2 Gbps/600 MHz) * HDR-10: 10-bit color at 4K 60 Hz 4:2:0 and 4K 24 Hz 4:4:4 * Dolby® Vision™ HDR: 12-bit color at 4K 60Hz 4:2:0 and 4K 24 Hz 4:4:4 * HDCP 2.2 and 1.4 * 12-bit Deep Color (at 1080p) * Uncompressed LPCM digital audio up to 7.1 channels * HBR (High Bit Rate) digital audio up to 7.1 channels, including Dolby Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™ * 3DTV pass-through * CEC pass-through * Lip Sync pass-through • Supports the use of DVI sources and DVI displays up to 1080p Full HD and WUXGA (1920x1200), with Gefen CAB-DVI2HDMI-LCK DVI-to-HDMI cables (not included) • RS-232 2-way link between Sender and Receiver • IR extension from Sender to Receiver and from Receiver to Sender • Gefen’s Bi-Directional POL provides power to the Sender or the Receiver unit over the link cable - only one side will need external power • Uses Gefen’s implementation of HDBaseT™ technology with proprietary algorithms and enhanced features • Advanced EDID Management • Firmware updatable via RS-232 using Gefen Syner-G™ • Locking power connector • Plug & Play – no configuration or set-up required for most applications • Surface mountable • Compact enclosures are easy to install and can be hidden away *Features and specifications are subject to change without notice. All trademarks and registered trademarks are properties of their respective owners. 6 Features & Packing List Features (GTB-UHD600-HBTL)* • Supports 18.2 Gbps bandwidth and 600 MHz TMDS clock • Extends HDMI & Bi-Directional IR over a single CAT-5e/CAT-6A: • * 4K Ultra HD (3840 x 2160 to 60 Hz, 4:4:4), up to 132 feet/40 meters (8-bit color) * 4K Cinema (DCI) (4096 x 2160 to 60 Hz 4:4:4), up to 132 feet/40 meters (8-bit color) * 1080p Full HD (60 Hz) and WUXGA (1920 x 1200 to 60 Hz), up to 200 feet/60 meters (up to 12-bit Deep Color) HDMI Features Supported: * HDMI 2.0 (full bandwidth to 18.2 Gbps/600 MHz) * HDR-10: 10-bit color at 4K 60 Hz 4:2:0 and 4K 24 Hz 4:4:4 * Dolby® Vision™ HDR: 12-bit color at 4K 60Hz 4:2:0 and 4K 24 Hz 4:4:4 * HDCP 2.2 and 1.4 * 12-bit Deep Color (at 1080p) * Uncompressed LPCM digital audio up to 7.1 channels * HBR (High Bit Rate) digital audio up to 7.1 channels, including Dolby Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™ * 3DTV pass-through * CEC pass-through * Lip Sync pass-through • Supports the use of DVI sources and DVI displays up to 1080p Full HD and WUXGA (1920x1200), with Gefen CAB-DVI2HDMI-LCK DVI-to-HDMI cables (not included) • IR extension from Sender to Receiver and from Receiver to Sender • Gefen’s Bi-Directional POL provides power to the Sender or the Receiver unit over the link cable - only one side will need external power • Uses Gefen’s implementation of HDBaseT™ technology with proprietary algorithms and enhanced features • Advanced EDID Management • Firmware updatable via Gefen Syner-G™ port • Locking power connector • Plug & Play – no configuration or set-up required for most applications • Surface mountable • Compact enclosures are easy to install and can be hidden away *Features and specifications are subject to change without notice. All trademarks and registered trademarks are properties of their respective owners. 7 Features & Packing List Packing List* (GTB-UHD600-HBT) The following items are included in the GTB-UHD600-HBT package. If any of these items are not present in the box when you first open it, please contact Gefen Technical Support as soon as possible. (1) (1) (1) (1) (1) (1) Sender Unit (GTB-UHD600-HBT-TX) Receiver Unit (GTB-UHD600-HBT-RX) HDMI-to-HDMI Male-to-Male Locking cable, 6 feet IR Emitter (EXT-IREMIT) IR Extender (EXT-RMT-EXTIRN) 12V DC power supply with US/EU/UK/AU reginal AC plugs and 5.5mm/2.1mm DC plug (EXT-PS121.5AIP-LP-6) Packing List* (GTB-UHD600-HBTL) The following items are included in the GTB-UHD600-HBTL. If any of these items are not present in the box when you first open it, please contact Gefen Technical Support as soon as possible. • • • • • • (1) (1) (1) (1) (1) (1) Sender Unit (GTB-UHD600-HBTL-TX) Receiver Unit (GTB-UHD600-HBTL-RX) HDMI-to-HDMI Male-to-Male Locking cable, 6 feet IR Emitter (EXT-IREMIT) IR Extender (EXT-RMT-EXTIRN) 12V DC power supply with US/EU/UK/AU reginal AC plugs and 5.5mm/2.1mm DC plug (EXT-PS121.5AIP-LP-6) *Features and specifications are subject to change without notice. All trademarks and registered trademarks are properties of their respective owners. 8 Table of Contents Introduction.................................................................................................................... 10 GTB-UHD600-HBT................................................................................................................10 GTB-UHD600-HBTL.............................................................................................................. 15 Installation.....................................................................................................................20 Connection Instructions....................................................................................................... 20 Sample Wiring Diagrams...................................................................................................... 21 LED Status.......................................................................................................................22 IR Control........................................................................................................................ 23 Controlling the Source from the Viewing Location..............................................................23 Controlling the Display from the Source Location...............................................................24 Controlling the Source / Display from the Head-End and Viewing Locations �������������������25 DIP Switch Configuration..............................................................................................26 EDID Management................................................................................................................26 RS-232*............................................................................................................................ 27 Firmware Update...........................................................................................................28 Specifications.................................................................................................................29 * GTB-UHD600-HBT only 9 Introduction GTB-UHD600-HBT Sender Unit 1 3 GTB-UHD600-HBT-TX Link Power HDMI 2 Link Tx Rx G On ON Off 5 IR Out RS-232 Prog HDMI In 6 7 8 9 10 1 2 4 1 IR In/Ext ON 12V DC 11 10 Introduction ID Name Description 1 Power This LED indicator glows solid blue when the unit is powered. See LED Status (page 22) for more information. 2 Link This LED glows solid green when a link is established between the Sender and Receiver. See LED Status (page 22) for more information. 3 HDMI This LED indicator glows solid green when a source is connected to the HDMI In port. See LED Status (page 22) for more information. 4 12V DC This power receptacle is used to connect the included 12V DC power supply. Only one power supply is required for the extender system to operate. The power supply can be connected to either the Sender or Receiver unit. 5 Link Connect a CAT-5e or better cable, shielded CAT6A preferred, up to the recommended length for a given resolution, from this port to the Link port on the Receiver unit. 6 IR In/Ext 3.5mm mini-stereo jack. Connect an IR Extender (Gefen part no. EXT-RMT-EXTIRN) to this port. Alternatively, connect a 3.5mm mini-stereo connector from this port to the output of an automation system with an electrical IR output. See IR Control (page 23) for more information on using IR. 7 IR Out Connect an EXT-IREMIT IR Emitter (1 pc included) from this port to the IR sensor of the device to be controlled. See IR Control (page 23) for more information on using IR. 11 Introduction ID Name Description 8 RS-232 Connect RS-232 Tx, Rx, and Ground from an automation control device, using the removable 3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 port of the Sender unit. 9 Prog For normal operation, this switch should be in the Off (down) position. Setting this switch to the On (up) position, places the unit in firmware update mode. If either the Sender or the Receiver switch is in On position, extenders will not work. For the new setting of this switch to take effect, power needs to be removed from the unit by removing and reinstated by reconnecting them. 10 HDMI In Use the included Locking HDMI cable to connect an Ultra HD source to this HDMI port. 11 DIP Switches These DIP switches provide EDID management. See DIP Switch Configuration (page 26) for more information. Receiver Unit 1 3 GTB-UHD600-HBT-RX Link Power HDMI 2 Link Tx Rx G On ON Off 12V DC 4 5 1 IR In/Ext IR Out RS-232 Prog HDMI Out 6 7 8 9 10 12 Introduction ID Name Description 1 Power This LED indicator glows solid blue when the unit is powered. See LED Status (page 22) for more information. 2 Link This LED glows solid green when a link is established between the Sender and Receiver. See LED Status (page 22) for more information. 3 HDMI This LED indicator glows solid green when a source is connected to the HDMI In port. See LED Status (page 22) for more information. 4 12V DC This power receptacle can be used to connect the included 12V DC power supply. Only one power supply is required for the extender system to operate. The power supply can be connected to either the Sender or Receiver unit. 5 Link Connect a CAT-5e or better cable, shielded CAT6A preferred, up to the recommended length for a given resolution, from this port to the Link port on the Sender unit. 6 IR In/Ext 3.5mm mini-stereo jack. Connect an IR Extender (Gefen part no. EXT-RMT-EXTIRN) to this port. Alternatively, connect a 3.5mm mini-stereo connector from this port to the output of an automation system with an electrical IR output. See IR Control (page 23) for more information on using IR. 7 IR Out Connect an EXT-IREMIT IR Emitter (1 pc included) from this port to the IR sensor of the device to be controlled. See IR Control (page 23) for more information on using IR. 13 Introduction ID Name Description 8 RS-232 Connect Tx, Rx, and Ground from an automation control device, using the removable 3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 port of the Receiver unit. 9 Prog For normal operation, this switch should be in the Off (down) position. Setting this switch to the On (up) position, places the unit in firmware update mode. If either the Sender or the Receiver switch is in On position, extenders will not work. For the new setting of this switch to take effect, power needs to be removed from the unit by removing and reinstated by reconnecting them. 10 HDMI Out Use a Gefen Locking HDMI cable, up to 10 feet long, to connect an Ultra HD display to this HDMI port. 14 Introduction GTB-UHD600-HBTL Sender Unit 1 3 GTB-UHD600-HBTL-TX Link Power HDMI 2 Tx Rx G On ON Off 4 IR In/Ext 5 6 IR Out Syner-G™ 7 8 1 Prog HDMI In 9 10 ON 12V DC 1 2 Link 11 15 Introduction ID Name Description 1 Power This LED indicator glows solid blue when the unit is powered. See LED Status (page 22) for more information. 2 Link This LED glows solid green when a link is established between the Sender and Receiver. See LED Status (page 22) for more information. 3 HDMI This LED indicator glows solid green when a source is connected to the HDMI In port. See LED Status (page 22) for more information. 4 12V DC This power receptacle can be used to connect the included 12V DC power supply. Only one power supply is required for the extender system to operate. The power supply can be connected to either the Sender or Receiver unit. 5 Link Connect a CAT-5e or better cable, shielded CAT6A preferred, up to the recommended length for a given resolution, from this port to the Link port on the Receiver unit. 6 IR In/Ext 3.5mm mini-stereo jack. Connect an IR Extender (Gefen part no. EXT-RMT-EXTIRN) to this port. Alternatively, connect a 3.5mm mini-stereo connector from this port to the output of an automation system with an electrical IR output. See IR Control (page 23) for more information on using IR. 7 IR Out Connect an EXT-IREMIT IR Emitter (1 pc included) from this port to the IR sensor of the device to be controlled. See IR Control (page 23) for more information on using IR. 16 Introduction ID Name Description 8 Syner-G™ This port is used for firmware update using Gefen Syner-G™ 9 Prog For normal operation, this switch should be in the Off (down) position. Setting this switch to the On (up) position, places the unit in firmware update mode. If either the Sender or the Receiver switch is in On position, extenders will not work. For the new setting of this switch to take effect, power needs to be removed from the unit by removing and reinstated by reconnecting them. 10 HDMI In Use the included Locking HDMI cable to connect an Ultra HD source to this HDMI port. 11 DIP Switches These DIP switches provide EDID management. See DIP Switch Configuration (page 26) for more information. Receiver Unit 1 3 GTB-UHD600-HBTL-RX Link Power HDMI 2 Link Tx Rx G On ON Off 12V DC 4 IR In/Ext 5 6 IR Out Syner-G™ 7 8 17 1 Prog HDMI Out 9 10 Introduction ID Name Description 1 Power This LED indicator glows solid blue when the unit is powered. See LED Status (page 22) for more information. 2 Link This LED glows solid green when a link is established between the Sender and Receiver. See LED Status (page 22) for more information. 3 HDMI This LED indicator glows bright blue when an source is connected to the HDMI In port. 4 12V DC This power receptacle can be used to connect the included 12V DC power supply. Only one power supply is required for the extender system to operate. The power supply can be connected to either the Sender or Receiver unit. 5 Link Connect a CAT-5e or better cable, shielded CAT6A preferred, up to the recommended length for a given resolution, from this port to the Link port on the Sender unit. 6 IR In/Ext 3.5mm mini-stereo jack. Connect an IR Extender (Gefen part no. EXT-RMT-EXTIRN) to this port. Alternatively, connect a 3.5mm mini-stereo connector from this port to the output of an automation system with an electrical IR output. See IR Control (page 23) for more information on using IR. 7 IR Out Connect an EXT-IREMIT IR Emitter (1 pc included) from this port to the IR sensor of the device to be controlled. See IR Control (page 23) for more information on using IR. 8 Syner-G™ This port is used for firmware update using Gefen Syner-G™ 18 Introduction ID Name Description 9 Prog For normal operation, this switch should be in the Off (down) position. Setting this switch to the On (up) position, places the unit in firmware update mode. If either the Sender or the Receiver switch is in On position, extenders will not work. For the new setting of this switch to take effect, power needs to be removed from the unit by removing and reinstated by reconnecting them. 10 HDMI Out Use a Gefen Locking HDMI cable, up to 10 feet long, to connect an Ultra HD display to this HDMI port. 19 Installation Connection Instructions ►► Video 1. Connect the included HDMI locking cable between the Ultra Hi-Def source and the HDMI In port on the Sender unit. 2. Connect an Ultra HD display to the HDMI Out port on the Receiver unit using another Gefen HDMI locking cable. ►► CAT-5 3. Connect a CAT-5e or better cable, shielded CAT-6A preferred, from the Link port on the Sender unit to the Link port on the Receiver unit. Note Video resolution will affect maximum extension distance. Please see the Specifications section for recommended cable lengths. ►► IR 4. Refer to IR Control (page 23) for details on connecting IR devices. ►► RS-232 (GTB-UHD600-HBT only) 5. Connect Tx, Rx, and Ground from the RS-232 port of an automation control unit or a device-to-be-controlled, using the removable 3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 ports of the Sender and Receiver units. Each of the 3 pins is identified on the connector panel. ►► Power 6. Connect the included 12V DC power supply to the power receptacle on either the Sender or Receiver unit. Power to the other unit will be supplied through the Link cable. 7. Connect the AC plug of the power supply to an available electrical outlet. 20 Installation Sample Wiring Diagrams IR Extender (EXT-RMT-EXTIRN) OR 4K Ultra HD 600 MHz Source CAT-5e CABLE HDMI CABLE RS-232 CABLE IR IN IR OUT Automation Control Device GTB-UHD600-HBT-RX Receiver Unit OR IR Emitter (EXT-IREMIT) OR IR Extender (EXT-RMT-EXTIRN) RS-232 Controlled Device GTB-UHD600-HBT-TX Sender Unit Automation Control Device IR Emitter (EXT-IREMIT) 4K Ultra HD 600 MHz Display GTB-UHD600-HBT CAT-5e or better CABLE HDMI CABLE IR IN IR Extender (EXT-RMT-EXTIRN) OR 4K Ultra HD 600 MHz Source IR OUT Automation Control Device GTB-UHD600-HBTL-RX Receiver Unit IR Emitter OR Automation Control Device IR Extender (EXT-RMT-EXTIRN) GTB-UHD600-HBTL-TX Sender Unit IR Emitter 4K Ultra HD 600 MHz Display GTB-UHD600-HBTL Notes 1. The wiring diagrams above show an additional IR emitter (Gefen part no. EXT-IREMIT) and IR extender (Gefen part no. EXT-RMT-EXTIRN) that are not included with the product. These are available for purchase from your Gefen distributor. 2. Power supply connections are not shown in the diagrams above. Power supply can be connected to Sender or Receiver. The other unit will recerive power through the link cable, 21 LED Status The Power, Link, and HDMI LED indicators on the Sender and Receiver unit provide basic information on the current status of each unit. The information, in the table below, applies to both the Sender and Receiver unit. Power Description Solid blue • The Sender / Receiver unit is powered. Off • Check the power supply and the Link connection between the Sender and the Receiver unit. Link Description Solid green • Link integrity is good between the Sender and Receiver unit. Off • Check the power supply and the Link connection between the Sender and the Receiver unit. HDMI Description Solid green • Sender: Source is connected and powered. • Receiver: Display / sink device is connected and powered. • Connect a source to the Sender unit; connect a display/sink to the Receiver unit. Make sure both source and sink are powered. Off 22 IR Control Controlling the Source from the Viewing Location 1. Connect an EXT-RMT-EXTIRN IR Extender (1 pc included) to the IR In/Ext port on the Receiver unit. If using an automation system, connect the 3.5mm mini-stereo connector from the IR In/Ext port on the Receiver unit to the IR Output port of the automation system. IR signals will be transmitted over the Link cable. 2. Connect an EXT-IREMIT IR Emitter (1 pc included) from the IR Out port of the Sender unit, to the IR sensor window on the source device. Ultra HD source IR signals Link IR emitter Tx Rx G On ON Off 12V DC IR In/Ext IR Out Syner-G™ 1 Prog HDMI In Sender unit IR signals Link Tx Rx G On ON Off 12V DC IR In/Ext IR Out Syner-G™ 1 Prog HDMI Out Receiver unit to Ultra HD display IR extender IR signals IR signals or from Automation System 23 IR Control Controlling the Display from the Source Location 1. Connect an EXT-RMT-EXTIRN IR Extender (1 pc included) to the IR In/Ext port on the Sender unit. If using an automation system, connect the 3.5mm mini-stereo connector from the IR In/Ext port on the Receiver unit to the IR Output of the automation system. IR signals will be transmitted over the Link cable. 2. Connect an EXT-IREMIT IR Emitter (1 pc included) from the IR Out port on the Receiver unit to the IR sensor on the display. IR extender or IR signals from Automation System IR signals from Ultra HD source Link Tx Rx G On ON Off 12V DC IR In/Ext IR Out Syner-G™ 1 Prog HDMI In Sender unit IR signals Receiver unit Link Tx Rx G On ON Off 12V DC IR In/Ext IR Out Syner-G™ 1 Prog HDMI Out IR emitter Ultra HD display 24 IR Control Controlling the Source & Display from the Head-End and Viewing Locations 1. This set-up ewill require an additional EXT-RMT-EXTIRN and EXT-IREMIT, sold separately by your Gefen distributor. 2. Follow instructions on page 23 and 24. or IR extender IR signals from Automation System IR signals IR emitter IR Signals from Receiver unit Link Tx Rx G On ON Off 12V DC IR In/Ext IR Out Syner-G™ 1 Prog HDMI In Sender unit IR signals Receiver unit Link Tx Rx G On ON Off 12V DC IR In/Ext IR Out Syner-G™ 1 Prog HDMI Out IR emitter IR signals IR extender IR signals or IR Signals from Sender unit from Automation System 25 DIP Switch Configuration The Sender unit has 2 EDID Management DIP Switches on its bottom panel, under a selfadhesive cover. This product is shipped with its DIP switches set to enable 4K with 2-Channel Audio mode (SW1: OFF, SW2: ON). 1 2 ON 1 2 ON Refer to the table below for DIP switch settings. EDID Management SW 1 SW 2 EDID Mode OFF N/A External / Bypass EDID mode (default) • ON N/A DIP Switch Positions Allows all video and audio features of the connected device to be passed to the source device. Internal EDID mode • ON 1 2 ON Enables the EDID modes on SW2. 1 2 ON ON 4K 600 Multichannel Audio EDID mode • ON 4K 600 MHz w/ Multichannel Audio 1 2 ON OFF 4K 600 2-Channel Audio Mode (default) • ON 4K 600 MHz w/ 2-Channel Audio 1 2 26 RS-232* Connecting RS-232 Devices* The GTB-UHD600-HBT supports RS-232 extension. The RS-232 interface is also used to upgrade the firmware using the Gefen Syner-G™ software. 1. Connect RS-232 Tx, Rx, and Ground from an automation control device to the removable 3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 port of the Sender unit. Each of the 3 pins is identified on the connector panel. If your automation device has a male DB-9 port and you prefer to not do the wiring, you can purchase an ADA-PH2-DB9-MF-AB adaptor cable from your Gefen distributor. This adaptor cable has a female DB-9 on one end and a 3-pin Phoenix connector on the other. 2. Connect RS-232 Tx, Rx, and Ground from the device-to-be-controlled, to the removable 3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 port of the Receiver unit. Each of the 3 pins is identified on the connector panel. If the RS-232 device you wish to control has a female DB-9 port and you prefer to not do the wiring, you can purchase an ADA-PH-2-DB9-MM-AB adaptor cable from your Gefen distributor. This adaptor cable has a male DB-9 on one end and a 3-pin Phoenix connector on the other. 3. Since RS-232 is a bi-directional commuinications protocol, and depending on your application, you can also connect the automation controller to the receiver and the device-tobe-controlled to the sender. Link Tx Rx G On ON Off 12V DC IR In/Ext IR Out RS-232 1 Prog HDMI Out Important The Prog switch must be set to the OFF position in order to enable serial (RS-232) extension. In addition, when sending RS-232 commands, a CR (0x0D) must be included. * GTB-UHD600-HBT only 27 Firmeware Update Firmware Update 1. Sender and Receiver should each be updated separately. To ensure proper operation, always update both units. 2. A Windows PC that is running Gefen Syner-G™ software, needs to be connected to to the RS-232 port of the GTB-UHD600-HBT or the Syner-G™ port of the GTB-UHD600-HBTL. Sender and Receiver, either through a native RS-232 interface or using a USB-to-Serial adaptor. 3. Remove power from the unit to be updated, by disconnecting the 12V DC power supply and the Link connector. Make sure that the Prog switche on the Sender or Receiver is in On (up) position, and then re-apply power to the unit by connecting the included power supply to the 12V DC port and to an available electrical outlet. The power LED will glow to indicate that the unit is receiving power. 4. Connect RS-232 Tx, Rx, and Ground from the PC or USB-to-Serial adaptor to the removable 3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 or Syner-G™ port of the Sender or Receiver to be updated. Each of the 3 pins is identified on the connector panel. If your PC or USB-to-Serial adaptor has a male DB-9 port and you prefer to not do the wiring, you can purchase an ADA-PH-2-DB9-MF-AB adaptor cable from your Gefen distributor. This adaptor cable has a female DB-9 on one end and a 3-pin Phoenix connector on the other. 5. Follow on-screen instructions in Gefen Syner-G™ to perform the firmware update on each unit. 6. Once a unit has successfully been updated, remove power from the unit, set the Prog switch to Off (down) position, and reco0nnect the Link cable and the power supply. 28 Specifications* Supported Formats Maximum Video Resolution/Timing • • 4K Cinema - DCI (4096 x 2160 to 60Hz, 4:4:4) 4K Ultra HD (3840 x 2160 to 60Hz, 4:4:4) Audio (HDMI Pass-Thru) • Up to 8 channels of HBR, Bitstream, & LPCM Video Input Connector (Sender) • 1 x HDMI Type A 19-pin, locking, female Video Output Connector (Receiver) • 1 x HDMI Type A 19-pin, locking, female Link Connector (Sender / Receiver) • 1 x RJ-45, shielded RS-232 Connector (Sender / Receiver) • 1 x 3-pin Phoenix (GTB-UHD600-HBT only) Connectors & Indicators Syner-G™ Connector (Sender / Receiver) • 1 x 3-pin Phoenix (GTB-UHD600-HBTL only) IR In/Ext Connector (Sender / Receiver) • 1 x 3.5mm mini-stereo, female IR Out Connector (Sender / Receiver) • 1 x 3.5mm mini-stereo, female Power Connector (Sender / Receiver) • 1 x 12V DC, locking, 5.5mm barrel/2.1mm pin Power Indicator (Sender / Receiver) • 1 x LED, blue Link Indicator (Sender / Receiver) • 1 x LED, green HDMI Indicator (Sender / Receiver) • 1 x LED, green TMDS Clock • 600 MHz Video Bandwidth • 18.2 Gbps Power Consumption (Sender/Receiver) • 14 W (max.), combined Operating Temperature • +32 to +113 ºF (0 to +45 ºC) Operating Humidity • 5% to 90% RH, non-condensing Storage Temperature • -4 to +185 °F (-20 to +85 °C) Storage Humidity (RH) • 0% to 95% RH, non-condensing MTBF • 50000 hours Dimensions (W x H x D) (Sender / Receiver), not including connectors • 4.7” x 1” x 2.9” (119 mm x 26 mm x 73 mm) Net Weight (Sender/Receiver) • 0.31 lbs (0.14 kg) each Operational Physical * Features and specifications are subject to change without notice. All trademarks and registered trademarks are properties of their respective owners. Copyright© 2017 Core Brands, LLC 29 1800 S McDowell Blvd. Petaluma CA 94954, USA 1-707-283-5900 1-800-472-5555 Copyright© 2017 Core Brands, LLC.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c138 79.159824, 2016/09/14-01:09:01 Create Date : 2018:01:03 08:39:01-08:00 Metadata Date : 2018:01:03 08:39:05-08:00 Modify Date : 2018:01:03 08:39:05-08:00 Creator Tool : Adobe InDesign CC 2017 (Macintosh) Instance ID : uuid:7311cd9d-cb5f-2d45-9cbd-48812b6124ed Original Document ID : xmp.did:208FED43445CE211A75BEC20F72BF2CF Document ID : xmp.id:bc282f5b-3db0-4c49-b580-3b3360201f1b Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:3f3292be-0356-459a-aaac-9de3689955d2 Derived From Document ID : xmp.did:4a87e754-2b44-4fad-b125-77452c33dbc1 Derived From Original Document ID: xmp.did:208FED43445CE211A75BEC20F72BF2CF Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2017 (Macintosh) History Changed : / History When : 2018:01:03 08:39:01-08:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 30 Creator : Adobe InDesign CC 2017 (Macintosh)EXIF Metadata provided by EXIF.tools