Pdf Lx Xms 1010P Quick Install Guide User Manual

2017-11-17

User Manual: Manual Pdf Lx-Xms-1010P Quick-Install-Guide pdf_LX-XMS-1010P_quick-install-guide LX-XMS-1010P products

Open the PDF directly: View PDF PDF.
Page Count: 8

Scroll down to view the document on your mobile browser.
Fold Fold FoldREAD ME FIRSTQUICK INSTALL GUIDE10-Port/8 PoE+ Gigabit  Managed Switch XMS-1010PIncludes: XMS-1010P 10-Port/8 PoE+ Gigabit Managed Switch Rack Mount Kit Rubber Feet Power CordSETUP AND CONFIGURATION1Physical InstallationThe XMS-1010P can be rack-mounted or used as a desktop switch. Install the XMS-1010P in a stable/safe place to avoid any possible damage. Make sure there is adequate space around the XMS-1010P for ventilation and proper heat dissi-pation; Luxul recommends at least 4-6 inches around all sides. Avoid placement in direct sunlight. Do not place heavy articles on the XMS-1010P and verify the ground connection of the outlet is functioning properly.Desktop/Shelf InstallationFor desktop/shelf installation, attach the four rubber feet to the corner inden-tations on the bottom of the XMS-1010P, then place the switch horizontally on a solid, level platform.Rack InstallationUse the included L brackets for convenient installation in a 19-inch server or audio rack. As shown below, use four screws to attach the L-shaped brackets on either sides of the XMS-1010P, and horizontally insert the switch into the rack. Use your desired hardware to ax the switch supports to the rack.                         Attach feet for desktop installation                Install brackets for rack-mounting2Connecting Ethernet and PowerEthernet and Power ConnectionsUse any RJ-45 to connect the XMS-1010P to an Ethernet-enabled device,  including servers, routers or other switches. No crossover cable is necessary.   The XMS-1010P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/full-duplex mode and 1000 Mbps full-duplex mode. All ten RJ-45 ports support Auto MDI/MDIX and can be used as ordinary ports or as Uplink ports. Ports 1-8 are PoE+ and are enabled by default. Use the included power cable to connect the XMS-1010P to a surge protect-ed outlet. The AC input socket and a power switch are on the rear panel. The built-in power supply supports 100~240VAC at 50/60Hz. Network CablingLuxul recommends Category-5, super Category-5 or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best performance and stable data transmission at 1000 Mbps, use Category-6 shielded twisted pair.  cCAUTION:  Multiple Uplink channels can create loops, resulting in network failure. Ensure only one Uplink channel exists between switches or between the XMS-1010P and a router. nNOTE:  When powering up, the port LEDs corresponding to the opti-cal interface may take a moment to initialize. This is normal as the XMS-1010P initialization and startup completes. nNOTE:  The XMS-1010P has an internal 130W power supply. For optimal switch performance, do not exceed 115W combined consumption of all external PoE devices.Sales801-822-5450 sales@luxul.comTechnical Support801-822-5450 support@luxul.comLUX-QIG-XMS-1010P-v7 04131712Copyright and Trademark NoticesNo part of this document may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.© Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and registered trademarks are property of their respective holders.

Navigation menu