Marantec America D323315 Transmitter for Vehicular Environment User Manual USA 84574 GB 0508

Download:
Mirror Download [FCC.gov]
Document ID	974072
Application ID	/AAfxTImFr8uIzLwa2vXzw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.55kB (244386 bits)
Date Submitted	2008-07-22 00:00:00
Date Available	2008-07-22 00:00:00
Creation Date	2008-06-10 13:19:39
Producing Software	Corel PDF Engine Version 14.0.0.567
Document Lastmod	2008-06-10 13:19:39
Document Title	USA_84574_GB_0508.cdr
Document Creator	CorelDRAW
Document Author:	Marina Brüsse

Car Transmitter
Instructions
GB
for model: MV-0313
Figure 1. Using Transmitter
FEATURES
The 3-channel transmitter can be used problem-free over the 12 V
voltage supply of the cigarette lighter of each passenger car. The
transmitter is thereby at the same place and a battery change is no
longer necessary always.
Each transmitter is custom encoded and ergonomically designed to be
an integral part of your garage door opener system, with two styles to suit
your personal preference.
1. Using the transmitter
Put
the transmitter into the cigarette lighter of your car (Figure 1). To
open or close garage door, press and hold the button (The transmitter
has indicator lights). When garage door begins to move release
button.
To stop the garage door during travel, press and hold button until door
stops, then release button.
To continue the garage door travel after stopping it, press and hold the
button. Press button once, the door will travel in the opposite direction.
Figure 2. Multiple Transmitters-Code Transfer
fig. 2A
2. Multiple Transmitters (Figure 2)
Each car transmitter comes factory programmed with random codes.
The car transmitter code can be changed in order to match the code of
an "active" transmitter, which you are already using. Below are
instructions for transferring an active code from a button on one
transmitter to a button of your choice on the car transmitter.
Connect the transmitter with active code to the car transmitter using
the programming cable (fig. 2A).
Press and hold the selected channel button on the transmitter with the
active code (fig. 2B). The light in the transmitter illuminates.
Press and hold the respective channel button on the car transmitter
(fig. 2C). The light in the transmitter initially starts blinking and then
illuminates continuously after 1-2 sec. Code transfer is completed.
Programming cable can be removed and both transmitters can now be
used to operate the same door.
Cigarette
lighter
fig. 2B
Programming
cable
Car
Transmitter
Transmitter
with active Code
fig. 2C
Note: For multi-button transmitters, be sure to carry out this procedure
for all the buttons you desire to use.
Figure 3. Code Changing
3. Changing the Code on Transmitters (Figure 3)
The transmitter factory preset code can be changes as follows:
Connect the programming cable into the lateral socket of the car
transmitter to change the code.
Short one of the outer pins of the programming cable with the middle
pin.
Press and hold the respective channel button. The light will blink
rapidly for approx. 5 sec. Release the button after the light illuminates
continuously. Then remove the programming cable.
Note: Be sure to carry out this procedure for all the buttons you desire to
use.
FCC Certified: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.
84574
© 2008 All rights reserved.
08/05 GB
Transmitters
Instructions
GB
(continued)
4. Multiple Transmitters (Figure 3)
Each transmitter comes factory programmed with random
codes. 2-channel transmitters have 2 different random codes,
one per button, 3-channel transmitters have 3 different random
codes and 4-channel transmitters have 4 different random
codes, one per button. Transmitters that are purchased
separately as accessories have random codes that must be
changed in order to match the code of the "active" transmitter,
which you are alredy using. Below are instructions for
transferring an active code from a button on one transmitter to a
button of your choice on another transmitter.
Connect the transmitter with active code to the new
transmitter using the programming connector (fig. 3A).
Figure 3. Multiple Transmitters-Code Transfer
fig. 3A
Transmitter with active Code
Programming
Connector
new Transmitter
fig. 3B
Press and hold the selected channel button on the transmitter
with the active code (fig. 3B). The light in the transmitter
illuminates.
Press and hold the respective channel button on the new
transmitter (fig. 3C). The light in the transmitter initially starts
blinking and then illuminates continuously after 1-2 sec. Code
transfer is completed.
fig. 3C
Programming connector can be removed and both transmitters
can now be used to operate the same door.
Note: For multi-button transmitters, be sure to carry out this
procedure for all the buttons you desire to use.
5. Changing the Code on Transmitters (Figure 4)
The transmitter factory preset code can be changes as follows:
Connect the programming connector into the lateral socket of
the transmitter to change the code.
Figure 4. Code Changing
Short one of the outer pins of the programming connector with
the middle pin.
Press and hold the respective channel button. The light will blink
rapidly for approx. 5 sec. Release the button after the light
illuminates continuously. Then remove the programming
connector.
Note: For multi-button transmitters, be sure to carry out this
procedure for all the buttons you desire to use.
FCC Certified: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.
84577
© 2008 All rights reserved.
08/05 GB

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Create Date                     : D:20080610131939Z
Modify Date                     : D:20080610131939Z
Producer                        : Corel PDF Engine Version 14.0.0.567
Author                          : Marina Brüsse
Creator                         : CorelDRAW
Title                           : USA_84574_GB_0508.cdr

EXIF Metadata provided by EXIF.tools