Marvel Industries 3Swcce Users Manual
3SWCCE to the manual cb9c2285-4494-4250-8f21-f80465d139df
2015-02-05
: Marvel-Industries Marvel-Industries-3Swcce-Users-Manual-358013 marvel-industries-3swcce-users-manual-358013 marvel-industries pdf
Open the PDF directly: View PDF 
.
Page Count: 10
| Download | |
| Open PDF In Browser | View PDF |
MARVEL REFRIGERATED CHAMPAGNE CELLAR Installation Operation and Maintenance Instructions Refrigerated Champagne Cellar 3SWCCE UNPACKING YOUR WINE CELLAR Remove Packaging Your champagne cellar has been packed for shipment with all parts that could be damaged by movement securely fastened. Before using, be sure all packing materials and tape have been removed. Important Keep your carton packaging until your champagne cellar has been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed as proof of damage in transit. Note to Customer This merchandise was carefully packed and thoroughly inspected before leaving our plant. Responsibility for its safe delivery was assumed by the retailer upon acceptance of the shipment. Claims for loss or damage sustained in transit must be made on the retailer as follows: • Exterior and Concealed Damage Any damage must be reported immediately to your retailer. REMINDER IT IS IMPORTANT THAT YOU SEND IN YOUR WARRANTY RECORD CARD IMMEDIATELY AFTER TAKING DELIVERY OF YOUR CHAMPAGNE CELLAR. DO NOT RETURN DAMAGED MERCHANDISE TO THE MANUFACTURER - FILE THE CLAIM WITH THE RETAILER. Undercounter 30SWCCE Champagne Cellar Specifications Exterior Cabinet Dimensions WxHxD (in.) Weight Capacity Temperature Power Supply supplied with a 15 amp plug 1 14 7/8 x 34 1/4 x 23 5/8 128 lbs. 15 Bottles 40-65 °F 115VAC/60Hz INSTALLING YOUR WINE CELLAR Select Location The proper location will ensure peak performance of your appliance. Choose a location where the unit will be out of direct sunlight and away from heat sources. Best performance will be maintained when installed within the following parameters: Electrical Plug Optional Location: Cutout shown for electrical outlet which can be located in adjacent cabinetry. Ideal Ambient Temperature Range Built-In 65-80 °F Free-Standing 65-90 °F Cabinet Clearance Ventilation is required from the bottom front section of the unit. Keep this area open and clear of any obstructions. Leveling Legs Adjustable legs at the front corners of the unit should be set so the unit is firmly positioned on the floor and the front is raised just enough so that the door closes easily when opened about halfway. Turn leveling legs clockwise to raise unit, counterclockwise to lower it. Door Hinge Reversing You can change the door swing from right- to left-hand very easily. Simply unscrew the top and bottom hinge pin, lift the door off the bottom hinge, and switch the hinges to the other side. Screw the hinge pin back in what is now the bottom hinge, unscrew the hinge pin in what is now the top hinge, replace door, and screw the pin back in the top hinge. Power Supply Cord with 3-prong grounding plug Grounding Type Wall Receptacle Cord may be flush with back wall Figure 2 Electrical Connection Use nominal 115 VAC, 60 Hz only. DO NOT USE AN EXTENSION CORD. Grounding Method This product is factory equipped with a power supply cord that has a three-pronged, grounded plug. It must be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances (see Figure 1). If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable local codes and ordinances. The third ground prong should not, under any circumstances, be cut or removed (see Figure 2). All U.L. listed refrigerated products are equipped with this type of plug. Figure 1 2 SENTRY SYSTEM™ REFRIGERATION MONITOR ON OFF 55 F Set Warmer °F/C Colder Light Sentry System™ Power Failure - Flashing Amber High/Low Temp - Red Press ON/OFF - Reset Alarms OFF - Steady Amber Figure 3 Press and Hold Start Your Appliance Your appliance will start upon initial plug-in. The LED will flash amber upon initial plug-in due to your unit being powered-on at the factory to verify performance and then powered-off. The Sentry System™ refrigeration monitor senses a power outage has occurred and relays this information to you when you initially power-up your appliance. This is normal and pressing the “ON/OFF” button will reset this alarm function. If your appliance’s control has been shut off (i.e., unit plugged in, interior lights operate, display blank), unit must be turned on. To turn on your appliance, push and hold for five (5) seconds, the “ON/OFF” button located on the display panel (see Figure 3). Once loaded with champagne bottles, allow at least 48 hours for the unit to stabilize before making any adjustments to the initial setting. Set Your Temperature Mode This product can display either Fahrenheit or Celsius. To do so, press the “°F/C” button on the display panel. Set the Controls The available temperature range of the unit is from 40 to 65 degrees F. The temperature set point is initially set in the factory at 55 degrees F. The temperature set point can be lowered or raised by first pushing the “SET” button on the display pad. A “SET” icon will be displayed. Pushing either the “WARMER” or “COLDER” buttons located on the display pad will raise or lower the set temperature by one (1) degree F or C (depending on your setting). As with any refrigeration product, there is a slight temperature variance at different locations within the cabinet. Adjustable Temperature Control The temperature control is fully adjustable from the low forties to the mid-sixties. The range allows flexibility of temperature preferences. 3 Interior Light and Switch The interior light makes it easy to view your wine labels and enhances the display of your collection. To engage the display light, press the “LIGHT” button on the display panel. The light will come on and stay on with the door closed. To disable the display light, press the “LIGHT” button again. The light will always come on when the door is opened. Warning Alarms Your champagne cellar has been fitted with a Sentry System™ refrigeration monitor. This monitor will let you know if your cellar is not functioning properly for optimum storage. Door Ajar Alarm If the door has been left open for over five (5) minutes, the alarm will sound and the LED will flash green. This will stop as soon as the door is closed. High and Low Temperature If your unit reaches temperatures outside normal operating temperatures for your set point for more than one (1) hour, an alarm will sound and the LED will flash red. This will warn you that your champagne has seen temperatures that may not be conducive for long-term storage. Power Failure If your unit experiences a power failure, the LED will flash amber until the alarm is reset. Reset Alarms Press the “ON/OFF” button for approximately one (1) second. This will reset all audible and display alarms. Sabbath Mode Your champagne cellar is equipped with a Sabbath Mode feature. By activating this mode, you will be disabling all displays, audible alarms and lights. To activate Sabbath Mode, press and hold the “SET” button while pressing the “°F/C” button four (4) times within seven (7) seconds. To deactivate Sabbath Mode, repeat the process. Sabbath Mode will automatically deactivate after 72 hours. 3SWCCE CHAMPAGNE CELLAR FEATURES Insert Champagne Bottles The five (5) roll-out shelves each hold three (3) bottles. See Figure 4 for typical wine bottle spacing. Tall bottles should not be loaded on the bottom rack because they may prevent the door from closing. Loading Tips and Suggestions Keep champagne that you plan to use for everyday drinking and entertaining on the front half of the racks where labels are completely visible. Place bottles for longer term storage in the rear (see Figure 5). Front Bottles (Necks Facing Rear) Rear Bottles (Necks Facing Front) Figure 4 Roll-out Racks The five (5) roll-out wine racks may be pulled out approximately fourteen (14) inches to facilitate adding or removing bottles. Do NOT lean on or press down heavily on the shelves. Doing so may damage the shelves and the champagne bottles stored on them. Pull the racks out gently and carefully to minimize unsettling your champagne collection. AVOID pulling out more than one (1) rack at any time to maintain stability. Single Bottle Racks Since bottles are not stacked on top of each other, you can easily view and access your inventory without disturbing other bottles (see Figure 6). Figure 5 Figure 6 4 CARE AND CLEANING OF YOUR CHAMPAGNE CELLAR Condenser The condenser tubing inside the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over the coils. Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the condenser for efficient performance by unscrewing the grille on the bottom front of the cabinet. Cabinet The stainless steel cabinet can be washed with either a stainless steel cleaner or a mild soap and water and thoroughly rinsed with clear water. NEVER use abrasive scouring cleaners. Interior Wash interior compartment with mild soap and water. Do NOT use an abrasive cleaner, solvent, polish cleaner or undiluted detergent. Roll-out Racks Tha racks may be cleaned with mild soap and water and a soft cloth. Do NOT use any abrasive cleaners. Door Gasket The vinyl gasket may be cleaned with mild soap and water, a baking soda solution or a mild scouring powder. Light Bulb Replacement WARNING! DISCONNECT THE POWER CORD BEFORE ATTEMPTING LIGHT BULB REPLACEMENT. Failure to do so may result in an electrical shock that could severely injure you. This unit uses one, 6 watt light tube to illuminate the interior of the champagne cellar. The light tube is a very reliable electrical component, but should it not function properly, please call the dealer you purchased your champagne cellar from for a replacement light tube. Use only an original equipment light tube from your dealer or Marvel Industries. Do NOT under any circumstance use a light tube that exceeds 10 watts! 5 To replace the light tube, use a hex-head driver to remove the two (2) hex-head screws holding the old light tube in place. Disconnect the electrical plug from the cabinet’s electrical receptacle and discard the old light tube. Reconnect the electrical plug of the the new light tube to the cabinet’s electrical recepatacle. Make sure it is secure and fully installed. Using the hex-head driver, resecure the two (2) hex-head screws to secure the light tube in place. Plug the champagne cellar into the electrical socket. Check to see if the light tube operates properly. Your light tube’s replacement is complete. The light tubes are not covered by your warranty. Replacement tubes can be obtained from your dealer or from Marvel Industries. In the Event of a Power Failure If a power failure occurs, try to correct it as soon as possible. Minimize the number of door openings while the power is off so as not to adversely affect the unit’s temperature. TROUBLESHOOTING YOUR CHAMPAGNE CELLAR Before Calling for Service Before calling for service, check the troubleshooting table on this page. This table lists possible problems that you can remedy without difficulty to avoid an unnecessary service call. PROBLEM Odor in cabinet Noisy operation Cabinet vibrates Cabinet light not working POSSIBLE CAUSES/SOLUTIONS 1. Interior needs cleaning 1. Cabinet not level 2. Weak floor 1. Cabinet not level 2. Weak floor 1. Tube burned out 2. No power at outlet 1. “ON/OFF” button pressed Appliance will not run 2. Power cord not plugged in 3. No power at electrical outlet 4. House fuse blown 1. Prolonged door openings Appliance runs too long 2. Control set too cold 3. Condenser needs cleaning Help Prevent Tragedies Each year children die because they climb inside a discarded refrigeration product, get trapped inside and suffocate. Take precautions to prevent such tragedies by removing the door or by taping or chaining it shut before discarding. 1. Too many door openings Moisture collects inside 2. Prolonged door openings 3. Hot, humid weather increases condensation 4. Control improperly set Moisture collects on outside surface Interior too hot/too cold 1. Hot, humid weather increases condensation (as humidity decreases, moisture will disappear) 2. Control improperly set 1. Control improperly set 1. See “Warning Alarms” on page 3 2. See “Sentry System™ Control Quick Reference” Sentry System™ refrigeration monitor activated 3. Temperature alarm may occur after user selected temperature set point changes in excess of 10 degrees F, or during heavy usage conditions. This is normal and not a fault of the appliance. The Sentry System™ is monitoring the duration of large swings in temperature to protect your contents, and may alert you to this event. See “Reset Alarms” on page 4. 6 OBTAINING SERVICE FOR YOUR WINE CELLAR If You Do Need Service If you do need service, contact your dealer or Marvel Industries. In any correspondence, refer to the model number and serial number of your unit which is located on the upper left hand side of the wall liner. Retain your proof of purchase. You may want to record these numbers in the space below. For Your Records Date of Purchase Dealer’s Name Dealer’s Address Dealer’s City Dealer’s State Dealer’s Zip Appliance Serial Number Model Number Date Warranty Card Sent (Must be within 10 Days of Purchase) 7 How to Obtain Service Your refrigerated champagne cellar requires little service because the best and most up to date materials, equipment and quality methods are employed throughout the manufacturing process. If trouble occurs during normal operation, first check the troubleshooting chart on the previous page to see if any of these simple steps may correct the problem. If service becomes necessary: 1. If the product is within the first year warranty period, please call Marvel Customer Service at 800.428.6644 for directions on how to obtain warranty coverage in your area. 2. If the product is outside of the first year warranty period, Marvel Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www. lifeluxurymarvel.com under the service and support section. 3. In all correspondence regarding service, be sure to give the model number, serial number, and proof of purchase. 4. Try to have information or description of the nature of the problem, how long the unit has been running, the room temperature, and any additional information that may be helpful in quickly solving the problem. HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user. Additional Second Through Fifth Year Limited Parts Only Warrranty During the four years following expiration of the one year limited warranty, Marvel will supply replacement parts for the hermetically sealed refrigeration system which consists of the compressor, condenser, drier, accumulator, bypass valve, connecting tubing and the evaporator that are proven to be defective due to workmanship or materials subject to the conditions and exclusions below. The above warranties do not cover: • Shipping costs of replacement parts or returned defective parts. • Customer education or instructions on how to use the appliance. • Any content loss due to product failure. • Removal or installation. Nor do the above warranties cover failure of this product or its components due to: • Transportation or subsequent damages. • Commercial use or use other than normal household or small office. • Improper installation, misuse, abuse, accident or alteration, use on wiring not conforming to electrical codes, low or high voltages, failure to provide necessary maintenance, or other unreasonable use. Parts or Service Not Supplied or Designated by Marvel The above warranties also do not apply if: • The original bill of sale, deliver date, or serial number cannot be verified. • Defective parts are not returned for inspection if so requested by Marvel. • The refrigeration equipment is not in the possession of the original end use purchaser. The warranties set forth herein are the only warranties extended by Marvel Industries. Any implied warranties, including the implied warranty of merchantability, are limited to the duration of these express warranties. In no event shall Marvel Industries be liable for any consequential or incidental damages or expenses resulting from breach of these or any other warranties, whether express or implied. Some states do not allow the exclusion or limitation of consequential damages or a limitation on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may have other rights that may vary from state to state. No person, firm, or corporation is authorized to make any other warranty or assume any other obligation for Marvel Industries. These warranties apply only to products used in any of the fifty states of the United States and the District of Columbia. To obtain performance of this warranty, report any defects to: Marvel Industries P.O. Box 997 Richmond, Indiana 47375-0997 Phone: 800.428.6644 8 www.lifeluxurymarvel.com Marvel Industries P.O. Box 997 Richmond, IN 47375-0997 800.428.6644 An AGA Company 41010622 Rev. B 03.03.08 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:08:23 Instance ID : uuid:16deeafc-7969-e042-bc63-7a69377051cf Document ID : adobe:docid:indd:ea1de20a-66b1-11dc-b7d2-f4ac22feb4f1 Rendition Class : proof:pdf Manifest Link Form : DirectStream, DirectStream, DirectStream, DirectStream, DirectStream, DirectStream, DirectStream Manifest Placed X Resolution : 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00 Manifest Placed Y Resolution : 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:488DFE9FF4CBDB119B64C2B5DDF18B0B, uuid:E257368B9293DC11B8DBD1DCA414E3ED, uuid:9A3DC54715EADC11BB12E2AF758E4AA2, uuid:FC558836CBEADC118B58856B127C877B, uuid:556D9357CBEADC118B58856B127C877B, uuid:285AE069CBEADC118B58856B127C877B, uuid:C6E924267334DC11B917B9D7ED780CCD Manifest Reference Document ID : uuid:458DFE9FF4CBDB119B64C2B5DDF18B0B, uuid:E157368B9293DC11B8DBD1DCA414E3ED, uuid:993DC54715EADC11BB12E2AF758E4AA2, uuid:D06342ABBAEADC118B58856B127C877B, uuid:546D9357CBEADC118B58856B127C877B, uuid:275AE069CBEADC118B58856B127C877B, uuid:C5E924267334DC11B917B9D7ED780CCD Create Date : 2008:05:08 09:47:57-04:00 Modify Date : 2008:09:11 16:03:25-04:00 Metadata Date : 2008:09:11 16:03:25-04:00 Creator Tool : Adobe InDesign CS3 (5.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 6365 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 8.0 Trapped : False Page Count : 10 Creator : Adobe InDesign CS3 (5.0)EXIF Metadata provided by EXIF.tools