Marvel Industries 3Swcce Users Manual

3SWCCE to the manual cb9c2285-4494-4250-8f21-f80465d139df

: Marvel-Industries Marvel-Industries-3Swcce-Users-Manual-358013 marvel-industries-3swcce-users-manual-358013 marvel-industries pdf

Open the PDF directly: View PDF .
Page Count: 10

Installation

Operation

and

Maintenance

Instructions

Refrigerated

Champagne Cellar

3SWCCE

MARVEL REFRIGERATED CHAMPAGNE CELLAR

Remove Packaging

Your champagne cellar has been packed for shipment with all

parts that could be damaged by movement securely fastened.

Before using, be sure all packing materials and tape have

been removed.

Important

Keep your carton packaging until your champagne cellar has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its safe

delivery was assumed by the retailer upon acceptance of the

shipment. Claims for loss or damage sustained in transit

must be made on the retailer as follows:

Exterior and Concealed Damage •

Any damage must be reported immediately to your retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE RETAILER.

IT IS IMPORTANT THAT YOU SEND

IN YOUR WARRANTY RECORD CARD

IMMEDIATELY AFTER TAKING DELIVERY

OF YOUR CHAMPAGNE CELLAR.

REMINDER

UNPACKING YOUR WINE CELLAR

1

Undercounter 30SWCCE Champagne Cellar

Specifications

Exterior Cabinet Dimensions

WxHxD (in.) 14 7/8 x 34 1/4 x 23 5/8

Weight 128 lbs.

Capacity 15 Bottles

Temperature 40-65 °F

Power Supply

supplied with a 15 amp plug 115VAC/60Hz

INSTALLING YOUR WINE CELLAR

2

Figure 1

Select Location

The proper location will ensure peak performance of your

appliance. Choose a location where the unit will be out of

direct sunlight and away from heat sources. Best perfor-

mance will be maintained when installed within the follow-

ing parameters:

Ideal Ambient Temperature Range

Built-In 65-80 °F

Free-Standing 65-90 °F

Cabinet Clearance

Ventilation is required from the bottom front section of the

unit. Keep this area open and clear of any obstructions.

Leveling Legs

Adjustable legs at the front corners of the unit should be

set so the unit is firmly positioned on the floor and the front

is raised just enough so that the door closes easily when

opened about halfway.

Turn leveling legs clockwise to raise unit, counterclockwise

to lower it.

Door Hinge Reversing

You can change the door swing from right- to left-hand

very easily. Simply unscrew the top and bottom hinge pin,

lift the door off the bottom hinge, and switch the hinges to

the other side. Screw the hinge pin back in what is now

the bottom hinge, unscrew the hinge pin in what is now the

top hinge, replace door, and screw the pin back in the top

hinge.

Electrical Connection

Use nominal 115 VAC, 60 Hz only. DO NOT USE AN

EXTENSION CORD.

Grounding Method

This product is factory equipped with a power supply cord

that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 1). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to exchange the existing

receptacle in accordance with the National Electrical Code

and applicable local codes and ordinances. The third

ground prong should not, under any circumstances, be cut

or removed (see Figure 2). All U.L. listed refrigerated prod-

ucts are equipped with this type of plug.

Figure 2

Electrical Plug Optional Location: Cutout shown for

electrical outlet which can be located in adjacent

cabinetry.

Power Supply Cord with

3-prong grounding plug

Grounding Type Wall

Receptacle

Cord may be flush

with back wall

Start Your Appliance

Your appliance will start upon initial plug-in. The LED will

flash amber upon initial plug-in due to your unit being

powered-on at the factory to verify performance and then

powered-off. The Sentry System™ refrigeration monitor

senses a power outage has occurred and relays this infor-

mation to you when you initially power-up your appliance.

This is normal and pressing the “ON/OFF” button will reset

this alarm function.

If your appliance’s control has been shut off (i.e., unit

plugged in, interior lights operate, display blank), unit must

be turned on. To turn on your appliance, push and hold

for five (5) seconds, the “ON/OFF” button located on the

display panel (see Figure 3).

Once loaded with champagne bottles, allow at least 48

hours for the unit to stabilize before making any adjust-

ments to the initial setting.

Set Your Temperature Mode

This product can display either Fahrenheit or Celsius. To

do so, press the “°F/C” button on the display panel.

Set the Controls

The available temperature range of the unit is from 40 to

65 degrees F. The temperature set point is initially set in

the factory at 55 degrees F. The temperature set point can

be lowered or raised by first pushing the “SET” button on

the display pad. A “SET” icon will be displayed. Pushing

either the “WARMER” or “COLDER” buttons located on the

display pad will raise or lower the set temperature by one

(1) degree F or C (depending on your setting). As with any

refrigeration product, there is a slight temperature variance

at different locations within the cabinet.

Adjustable Temperature Control

The temperature control is fully adjustable from the low

forties to the mid-sixties. The range allows flexibility of

temperature preferences.

Interior Light and Switch

The interior light makes it easy to view your wine labels and

enhances the display of your collection. To engage the dis-

play light, press the “LIGHT” button on the display panel.

The light will come on and stay on with the door closed. To

disable the display light, press the “LIGHT” button again.

The light will always come on when the door is opened.

Warning Alarms

Your champagne cellar has been fitted with a Sentry

System™ refrigeration monitor. This monitor will let you

know if your cellar is not functioning properly for optimum

storage.

Door Ajar Alarm

If the door has been left open for over five (5) minutes, the

alarm will sound and the LED will flash green. This will

stop as soon as the door is closed.

High and Low Temperature

If your unit reaches temperatures outside normal operating

temperatures for your set point for more than one (1) hour,

an alarm will sound and the LED will flash red. This will

warn you that your champagne has seen temperatures that

may not be conducive for long-term storage.

Power Failure

If your unit experiences a power failure, the LED will flash

amber until the alarm is reset.

Reset Alarms

Press the “ON/OFF” button for approximately one (1) sec-

ond. This will reset all audible and display alarms.

Sabbath Mode

Your champagne cellar is equipped with a Sabbath Mode

feature. By activating this mode, you will be disabling all

displays, audible alarms and lights.

To activate Sabbath Mode, press and hold the “SET” but-

ton while pressing the “°F/C” button four (4) times within

seven (7) seconds. To deactivate Sabbath Mode, repeat the

process. Sabbath Mode will automatically deactivate after

72 hours.

Figure 3

SENTRY SYSTEM™ REFRIGERATION MONITOR

3

55

ON

OFF

F

Press and Hold

Set Warmer

Colder

°F/C

Light

Sentry System™

Power Failure - Flashing Amber

High/Low Temp - Red

Press ON/OFF - Reset

Alarms OFF - Steady Amber

3SWCCE CHAMPAGNE CELLAR FEATURES

Insert Champagne Bottles

The five (5) roll-out shelves each hold three (3) bottles. See

Figure 4 for typical wine bottle spacing. Tall bottles should

not be loaded on the bottom rack because they may pre-

vent the door from closing.

Loading Tips and Suggestions

Keep champagne that you plan to use for everyday drink-

ing and entertaining on the front half of the racks where

labels are completely visible. Place bottles for longer term

storage in the rear (see Figure 5).

Roll-out Racks

The five (5) roll-out wine racks may be pulled out approxi-

mately fourteen (14) inches to facilitate adding or remov-

ing bottles. Do NOT lean on or press down heavily on the

shelves. Doing so may damage the shelves and the cham-

pagne bottles stored on them. Pull the racks out gently and

carefully to minimize unsettling your champagne collection.

AVOID pulling out more than one (1) rack at any time to

maintain stability.

Single Bottle Racks

Since bottles are not stacked on top of each other, you can

easily view and access your inventory without disturbing

other bottles (see Figure 6).

Front Bottles (Necks Facing Rear)

Rear Bottles (Necks Facing Front)

Figure 4

Figure 5

Figure 6

4

CARE AND CLEANING OF YOUR CHAMPAGNE CELLAR

Condenser

The condenser tubing inside the cabinet does not require

frequent cleaning; however, satisfactory cooling depends

on adequate ventilation over the coils. Be sure that noth-

ing obstructs the required air flow openings in front of the

cabinet. At least once or twice a year, brush or vacuum lint

and dirt from the condenser for efficient performance by

unscrewing the grille on the bottom front of the cabinet.

Cabinet

The stainless steel cabinet can be washed with either

a stainless steel cleaner or a mild soap and water and

thoroughly rinsed with clear water. NEVER use abrasive

scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Roll-out Racks

Tha racks may be cleaned with mild soap and water and a

soft cloth. Do NOT use any abrasive cleaners.

Door Gasket

The vinyl gasket may be cleaned with mild soap and water,

a baking soda solution or a mild scouring powder.

Light Bulb Replacement

WARNING! DISCONNECT THE POWER CORD BEFORE

ATTEMPTING LIGHT BULB REPLACEMENT. Failure to do so

may result in an electrical shock that could severely injure

you.

This unit uses one, 6 watt light tube to illuminate the interi-

or of the champagne cellar. The light tube is a very reliable

electrical component, but should it not function properly,

please call the dealer you purchased your champagne cel-

lar from for a replacement light tube. Use only an original

equipment light tube from your dealer or Marvel Industries.

Do NOT under any circumstance use a light tube that

exceeds 10 watts!

To replace the light tube, use a hex-head driver to remove

the two (2) hex-head screws holding the old light tube in

place. Disconnect the electrical plug from the cabinet’s

electrical receptacle and discard the old light tube. Re-

connect the electrical plug of the the new light tube to the

cabinet’s electrical recepatacle. Make sure it is secure and

fully installed.

Using the hex-head driver, resecure the two (2) hex-head

screws to secure the light tube in place. Plug the cham-

pagne cellar into the electrical socket. Check to see if the

light tube operates properly. Your light tube’s replacement

is complete.

The light tubes are not covered by your warranty. Replace-

ment tubes can be obtained from your dealer or from

Marvel Industries.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the unit’s tem-

perature.

5

TROUBLESHOOTING YOUR CHAMPAGNE CELLAR

6

Before Calling for Service

Before calling for service, check the troubleshooting table on this page. This

table lists possible problems that you can remedy without difficulty to avoid an

unnecessary service call.

PROBLEM POSSIBLE CAUSES/SOLUTIONS

Odor in cabinet 1. Interior needs cleaning

Noisy operation 1. Cabinet not level

2. Weak floor

Cabinet vibrates 1. Cabinet not level

2. Weak floor

Cabinet light not working 1. Tube burned out

2. No power at outlet

Appliance will not run

1. “ON/OFF” button pressed

2. Power cord not plugged in

3. No power at electrical outlet

4. House fuse blown

Appliance runs too long

1. Prolonged door openings

2. Control set too cold

3. Condenser needs cleaning

Moisture collects inside

1. Too many door openings

2. Prolonged door openings

3. Hot, humid weather increases condensation

4. Control improperly set

Moisture collects on out-

side surface

1. Hot, humid weather increases condensation

(as humidity decreases, moisture will disappear)

2. Control improperly set

Interior too hot/too cold 1. Control improperly set

Sentry System™

refrigeration monitor

activated

1. See “Warning Alarms” on page 3

2. See “Sentry System™ Control Quick

Reference”

3. Temperature alarm may occur after user

selected temperature set point changes in

excess of 10 degrees F, or during heavy usage

conditions. This is normal and not a fault of the

appliance. The Sentry System™ is monitoring

the duration of large swings in temperature to

protect your contents, and may alert you to this

event. See “Reset Alarms” on page 4.

Help Prevent Tragedies

Each year children die because they

climb inside a discarded refrigera-

tion product, get trapped inside and

suffocate. Take precautions to prevent

such tragedies by removing the door

or by taping or chaining it shut before

discarding.

OBTAINING SERVICE FOR YOUR WINE CELLAR

If You Do Need Service

If you do need service, contact your dealer or Marvel Indus-

tries. In any correspondence, refer to the model number

and serial number of your unit which is located on the

upper left hand side of the wall liner. Retain your proof of

purchase. You may want to record these numbers in the

space below.

For Your Records

Date of Purchase

Dealer’s Name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip

Appliance Serial Number

Model Number

Date Warranty Card Sent

(Must be within 10 Days of

Purchase)

How to Obtain Service

Your refrigerated champagne cellar requires little service

because the best and most up to date materials, equipment

and quality methods are employed throughout the manu-

facturing process.

If trouble occurs during normal operation, first check the

troubleshooting chart on the previous page to see if any

of these simple steps may correct the problem. If service

becomes necessary:

If the product is within the first year warranty period, 1.

please call Marvel Customer Service at 800.428.6644

for directions on how to obtain warranty coverage in

your area.

If the product is outside of the first year warranty 2.

period, Marvel Customer Service can provide recom-

mendations of service centers in your area. A listing

of authorized service centers is also available at www.

lifeluxurymarvel.com under the service and support

section.

In all correspondence regarding service, be sure to 3.

give the model number, serial number, and proof of

purchase.

Try to have information or description of the nature of 4.

the problem, how long the unit has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

7

HOUSEHOLD PRODUCT WARRANTY

8

Entire Product

Limited One Year Parts and Labor Warranty

Marvel warrants that it will supply all necessary parts and

labor to repair or replace in the end user’s home or office,

any component which proves to be defective in material

or workmanship, subject to the condition and exclusions

stated below, for a period of one year from the date of

purchase by the end user.

Additional Second Through Fifth Year

Limited Parts Only Warrranty

During the four years following expiration of the one year

limited warranty, Marvel will supply replacement parts for

the hermetically sealed refrigeration system which consists

of the compressor, condenser, drier, accumulator, bypass

valve, connecting tubing and the evaporator that are

proven to be defective due to workmanship or materials

subject to the conditions and exclusions below.

The above warranties do not cover:

Shipping costs of replacement parts or returned defec-•

tive parts.

Customer education or instructions on how to use the •

appliance.

Any content loss due to product failure.•

Removal or installation.•

Nor do the above warranties cover failure of this product or

its components due to:

Transportation or subsequent damages.•

Commercial use or use other than normal household •

or small office.

Improper installation, misuse, abuse, accident or •

alteration, use on wiring not conforming to electrical

codes, low or high voltages, failure to provide neces-

sary maintenance, or other unreasonable use.

Parts or Service

Not Supplied or Designated by Marvel

The above warranties also do not apply if:

The original bill of sale, deliver date, or serial number •

cannot be verified.

Defective parts are not returned for inspection if so •

requested by Marvel.

The refrigeration equipment is not in the possession of •

the original end use purchaser.

The warranties set forth herein are the only warranties

extended by Marvel Industries. Any implied warranties, in-

cluding the implied warranty of merchantability, are limited

to the duration of these express warranties. In no event

shall Marvel Industries be liable for any consequential or

incidental damages or expenses resulting from breach of

these or any other warranties, whether express or implied.

Some states do not allow the exclusion or limitation of con-

sequential damages or a limitation on how long an implied

warranty lasts, so the above exclusion or limitation may not

apply to you. This warranty gives you specific legal rights

and you may have other rights that may vary from state to

state.

No person, firm, or corporation is authorized to make any

other warranty or assume any other obligation for Marvel

Industries. These warranties apply only to products used in

any of the fifty states of the United States and the District of

Columbia.

To obtain performance of this warranty, report any defects

to:

Marvel Industries

P.O. Box 997

Richmond, Indiana 47375-0997

Phone: 800.428.6644

Marvel Industries

P.O. Box 997

Richmond, IN

47375-0997

800.428.6644

An AGA Company

41010622 Rev. B

03.03.08

www.lifeluxurymarvel.com

All specifications and product designs subject to change without notice. Such revisions do not entitle

the buyer to corresponding changes, improvements, additions, replacements or compensation for

previously purchased products.