Mattel Toys A Division of Mattel 97993-02A4R Remote Control Toy Receiver User Manual 97471 0920 STREET BEAST

Download:
Mirror Download [FCC.gov]
Document ID	246188
Application ID	g7f9z/K9NpjMeMpXQr/Lww==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	33.33kB (416631 bits)
Date Submitted	2002-05-30 00:00:00
Date Available	2002-05-30 00:00:00
Creation Date	2002-01-15 23:24:40
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2002-05-10 12:19:32
Document Title	97471-0920 STREET BEAST
Document Creator	QuarkXPress(tm) 4.04
Document Author:	MSkoniec

97471-0920
CAUTION-ELECTRIC TOY:
NOT RECOMMENDED
FOR CHILDREN UNDER
6 YEARS OF AGE. AS WITH ALL ELECTRIC PRODUCTS,PRECAUTIONS SHOULD BE
OBSERVED DURING HANDLING AND USE TO PREVENT ELECTRIC SHOCK.
INPUT: 120VAC, 0.10VDC, 60Hz, 0.05A. OUTPUT: 11.5VDC, 1.05VA.
9.6V R/C
CONTENTS
Vehicle
Transmitter
9.6V NiCd Battery Pack
9.6V NiCd Charger
Keep these instructions for future reference: they contain important information.
IMPORTANT: Please read all “Consumer Information” (last page) before operating your vehicle.
CAUTION: Surfaces may become hot and cause burns if
electronics get wet. Do not operate vehicle through water or snow.
CHASSIS
Refer to label on transmitter and vehicle
for frequency. Do not race vehicles with
the same frequency.
TOP VIEW
BOTTOM VIEW
Steering Adjuster
(adjust, if necessary, to
keep vehicle running
straight)
On/Off Switch
BatteryDoor
Latch
Gear Selector
(high/low)
CONSUMER INFORMATION:
IMPORTANT:
• To avoid accidental operation, remove all
batteries when not in use.
Please read before operating your vehicle.
SAFETY INFORMATION
BATTERY SAFETY INFORMATION
Note to Adults: To ensure that the child’s
play is both safe and fun, please review all  Insure that battery polarity is correct.
operating instructions and safety rules with  Use only batteries of the type recommended
(or equivalent).
your child.
 Do not mix old and new batteries.
Safety Tips
 Do not mix alkaline, standard (carbon-zinc), or
rechargeable (nickel-cadmium) batteries.
• NEVER drive your vehicle on streets!
They’re for real cars!
 Remove used-up batteries immediately.
Remove batteries if vehicle will not be used
• DO NOT pick up vehicle while in motion.
for a long period.
• Keep fingers, hair and loose clothing
away from the tires and the wheel hubs
 Do not recharge non-rechargeable batteries.
while the vehicle is switched ON.
 Do not short-circuit terminals.
• Adult supervision is recommended when  Remove rechargeable batteries before
this vehicle is being operated.
recharging (if the batteries are designed to be
removable).
 Recharge batteries only under adult supervision (if the batteries are designed to be
removable).
 Dispose of batteries safely. Do not dispose of
batteries (or products containing non-replaceable batteries) in fire, as batteries may
explode or leak.
Battery Performance Note:
For best performance use alkaline batteries
(where disposable batteries are called for). If
your vehicle is supplied with standard (carbon-zinc) batteries for initial use and/or
demonstration purposes, we recommend
replacing them with alkaline batteries when
necessary. Battery life may vary depending on
battery brand.
QUICK TIPS
❶
❷
❸
❶ When your vehicle starts ❷ Radio interference can
to lose power, it may lose
make your vehicle run
functions or performbadly. Interference can
ance. It's time for fresh
be caused by other R/C
batteries (or a recharge).
vehicles running on the
Your vehicle's running
same frequency; electritime
may
change
cal wires; large buildings;
depending on your drivor CB radios. Try to stay
ing style.
away from these!
❹
❺
❸ Point your transmitter anten- ❹ Don’t drive your vehicle in ❺ Don’t store your vehicle
na up - not down toward
sand or through water or
near heat or in direct sunyour vehicle. If your vehicle
snow.
light. Always turn switchgets too far away, it won't
es OFF and remove all
work properly. If your transbatteries for storage.
mitter has a carry-loop feature, make sure the antenna
tipisremovedfromthecarryloop holder and straightened
before operating.
TROUBLESHOOTING - PROBLEM? - SOLUTIONS
SYMPTOM
• PROBABLE CAUSE
• CORRECTION
Vehicle runs slowly or will not run.
• Loose battery connection or vehicle switch not ON.
• Weak or uncharged rechargeable NiCd battery
• Weak transmitter battery.
• Check battery connector and vehicle switch.
• Charge battery or replace.
• Replace with fresh alkaline battery.
Power indicator light on transmitter does not light.
• Transmitter battery weak or not connected.
• Check connections and replace battery if required.
Erratic operation or only short range possible.
• Radio interference likely.
• Antenna snapped into carry-loop holder (if equipped).
• Change location - see Point 2, “Quick Tips.”
• Remove antenna tip from carry-loop holder and straighten.
Vehicle doesn’t work after going through water or snow. • Water in the electronics area.
• Vehicle will take several hours to dry. Allow to dry thoroughly overnight before trying again.
• Avoid driving in water or snow.
POWER SYSTEMS
Please follow the specific instructions on the next page for
detailed information regarding NiCd vehicle battery charging
and safety.
VEHICLE BATTERY INSTALLATION
Battery Door
1. Rotate battery latch to open position.
2. Insert battery pack into battery compartment and slide it away
from latch.
3. Make sure battery pack snaps securely in place and rotate
latch to locked position.
4. To remove battery pack: turn latch, slide battery pack toward
latch and lift out.
9.6v Battery
Battery Door Latch
TRANSMITTER BATTERY INSTALLATION
Your transmitter has special shifting features. Please refer to the
“SPECIAL FEATURES” page for detailed instructions.
antenna
makes a cool
carry loop!
1. To install transmitter battery, open battery door as shown.
2. Install one 9V battery with polarity (+/-) as shown inside battery
compartment.
3. Swing battery door closed and snap shut.
power
indicator
light
On/Off
Switch
vehicle controls
battery
door
battery
compartment
SPECIAL FEATURES
Your transmitter can operate in 3 different modes…for ultimate driving action!
LED indicator
Right control
button
ON/OFF switch
Left control
button
I. SPEEDSHIFTER™ MODE – 3-speed shifting and cool driving sounds
1. Turn the vehicle switch ON. Turn the transmitter ON. Don’t press either control button.
2. After 3 seconds you’ll hear a shifting sound. You’re now in SpeedShifter™ mode! Just like a real driver, you’ll have to shift up
through the “gears“…from first to third!
3. Press and release either control button to "start" your vehicle.
4. Press the left control button forward to drive forward in first gear. The LED indicator (and a horn beep) will tell you when to
shift. To shift, release the shifter control…then push it forward again and hold it down. Your vehicle’s speed (and sound) will
change when you change “gears.“ Your vehicle will "downshift" when you turn for more than 1 second.
• If you don’t shift when the LED comes on, the “motor whine” will tell you that you need to shift.
• If you shift too soon, your “transmission” will make a “grinding” sound…just like a real gearbox.
• Just like a real vehicle, your “transmission” has only one “gear” in reverse.
II. SOUND MODE – high-speed driving…with cool driving sounds
1. Turn the vehicle switch ON. Turn the transmitter ON.
2. Within 3 seconds, press the left control button forward and hold it down until the
LED indicator flashes.
3. Release the control button and the horn will beep. You’re now in Sound Mode.
4. Press and release either control button to "start" your vehicle.
5. Use the control buttons to drive with cool driving sounds.
III. MUTE MODE – high-speed driving…without sound
1. Turn the vehicle switch ON. Turn the transmitter ON.
2. Within 3 seconds, press the left control button backward and hold it down until the
LED indicator flashes.
3. Release the control button. You’re now in Mute Mode.
4. Use the control buttons to drive your vehicle.
To switch modes at any time, just turn the transmitter OFF, then back ON. Then follow the directions above.
VEHICLE OPERATION – after vehicle is placed in desired mode
FORWARD
REVERSE
LEFT
RIGHT
NiCd BATTERY INFORMATION
Please follow these instructions regarding
NiCd vehicle battery charging and safety.
Use charger only under adult supervision.
BATTERY CHARGING/CARE –
9.6V TURBO® BATTERY
1. Plug wall pack charger into standard
110/120 volt outlet.
2. Connect the wires leading from the
battery pack to the wall pack charger
connector. Make certain the two connectors are tightly snapped together.
3. To disconnect wires, push down on the
connector clip and pull apart.
4. Your battery pack consists of new parts
and materials; therefore, you should
charge the battery pack for 51/2 hours
the first two times you charge the battery. Subsequent charges will require
only 4 hours.
5. After charging for 4 hours, the battery
will feel warm. This condition is normal
for fully charged batteries.
6. Charging the battery pack for more
than 4 hours will not give you a longer
running time. 4 hours is all that is
required for a fully charged battery
pack.
7. Unlike alkaline batteries, where the
power loss is gradual, a NiCd (nickelcadmium) battery will run for its normal
running time, depending on your particular vehicle, and then lose most of its
power at once. It is time to recharge
the battery pack. Running time will
vary, depending upon which R/C vehicle you have.
8. After use, the battery pack will be hot!
Wait at least 20 minutes until the battery pack cools before recharging.
Recharging a warm or hot battery pack
will greatly reduce the number of times
your battery pack can be recharged.
RECHARGEABLE BATTERY INFORMATION:
Note to Adults:
 DO NOT RECHARGE BATTERY PACK
IF IT’S HOT. ALLOW IT TO COOL
BEFORE RECHARGING.
 DO NOT RECHARGE A BATTERY PACK
THAT SHOWS LEAKAGE OR CORROSION.
 DO NOT DISASSEMBLE THE BATTERY PACK. THE BATTERY PACK IS A
SEALED RECHARGEABLE NICKELCADMIUM BATTERY.
 DO NOT DISPOSE OF THE BATTERY
PACK IN FIRE.
 EXERCISE CAUTION IN HANDLING A
HOT BATTERY PACK.
 IF BATTERY PACK AND/OR CHARGER
ARE WET, THOROUGHLY DRY BEFORE
CHARGING.
 DO NOT RECHARGE NONRECHARGEABLE BATTERIES.
• Remove rechargeable batteries before
recharging. Recharge batteries only
under adult supervision.
• Regularly examine for damage to the
plug, enclosure and other parts. In the
event of any damage, the toy must not
be used with the transformer until the
damage has been repaired.
• This toy is not intended for children
under 6 years old. The transformer is
not a toy.
THIS PRODUCT USES A NICKEL-CADMIUM RECHARGEABLE BATTERY PACK. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
FOR FURTHER INFORMATION REGARDING BATTERIES OR THEIR DISPOSAL PLEASE CALL 1-888-557-TYCO.
90-DAY LIMITED WARRANTY – TYCO® R/C PRODUCTS
Mattel, Inc. warrants to the original consumer purchaser that this product will be free of defects in material and workmanship for ninety (90) days (unless specified in alternate warranties) from the date of purchase. Mattel will repair or replace the product, at our sole option, in the event of such a defect within the warranty period.
In the event of a defect covered under this warranty, first call the toll-free number listed below. Many problems can be solved in this manner. If necessary, you will be
instructed to return the product, postage prepaid and insured, to the address below. Enclose your name, address, dated sales receipt, and a brief explanation of the defect.
Repair or replacement, and return shipment, will be free of charge. Please return only the defective part or unit, packed securely.
This warranty does not cover damage resulting from unauthorized modification, accident, misuse or abuse. If the product is returned without a dated sales receipt the product
may be excluded from coverage under this warranty.
Mattel’s liability for defects in material and workmanship under this warranty shall be limited to repair or replacement, at our sole option, and in no event shall we be responsible for incidental, consequential, or contingent damages (except in those states that do not allow this exclusion or limitation). This warranty is exclusive, and is made in lieu
of any express or implied warranty. Valid only in U.S.A. This warranty gives you specific legal rights and you may have other rights, which vary from state to state. Some
states do not allow the exclusion of incidental or consequential damages, so the above exclusions or limitations may not apply to you.
TOLL-FREE NUMBER: 1-888-557-TYCO (8926) (valid only in U.S.A.) Hours: 8:00 A.M. - 6:00 P.M. Eastern Time; Monday - Friday. Expect some delay in January following the holiday season. Please be patient and keep trying the toll-free number.
ADDRESS FOR RETURNS: CONSUMER RELATIONS, 636 GIRARD AVENUE, EAST AURORA, NY 14052
© 2001 Mattel, Inc., Mt. Laurel, NJ 08054 U.S.A.
PRINTED IN CHINA. All Rights Reserved. ® and ™
designate U.S. trademarks of Mattel, Inc.
COMPLIANCE WITH FCC REGULATIONS
THIS DEVICE COMPLIES WITH PART 15 OF FCC
RULES. OPERATION OF THIS DEVICE IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS:
Retain this address for future reference: Mattel
(1) THIS DEVICE MAY NOT CAUSE HARMFUL
U.K., Ltd., Vanwall Business Park, Maidenhead SL6 INTERFERENCE.
4UB. Mattel Australia Pty., Ltd., Richmond, Victoria (2) THIS DEVICE MUST ACCEPT ANY HARMFUL
3121 - Consumer Advisory Service: 1800 800 812
INTERFERENCE THAT MAY CAUSE UNDESIRED
(valid only in Australia). Mattel East Asia Limited, OPERATION.
930 Ocean Centre, Harbour City, HK, China.
This device generates and uses radio frequency
energy and if not used properly may cause inter-
ference to radio and television reception. It has
been tested and found to comply with the limits
set by the FCC, which are designed to provide reasonable protection against such interference.
CAUTION: FCC Regulations state that
changes or modifications to this product not
expressly approved by the manufacturer responsible for compliance could void the user’s authority
to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2002:01:15 23:24:40Z
Modify Date                     : 2002:05:10 12:19:32-03:00
Page Count                      : 6
Creation Date                   : 2002:01:15 23:24:40Z
Producer                        : Acrobat Distiller 4.0 for Macintosh
Author                          : MSkoniec
Mod Date                        : 2002:05:10 12:19:32-03:00
Metadata Date                   : 2002:05:10 12:19:32-03:00
Creator                         : MSkoniec
Title                           : 97471-0920 STREET BEAST

EXIF Metadata provided by EXIF.tools