Maxtronic Co AIBY Disk Array User Manual Aiby1400 Ch2
Maxtronic International Co Ltd Disk Array Aiby1400 Ch2
Contents
users manual 3
Chapter 2 : " Getting Started " General Overview This chapter helps you get ready to use the Disk Array. It gives you : Unpacking & Checklist Choosing a place for Disk Array Identifying Parts of Disk Array Power Source Installing the Hard Disk Drives Host Linkage Power-On and Self-test LED Display and Function Keys LCD Status Display The following illustrations will help you read the further sections. Special Note : RAID should never be considered a replacement for doing regular backup. It's highly recommended to conduct a backup strategy for critical data. 2-1 Getting Started Unpacking & Checklist Before unpacking your Disk Array , prepare a clean and stable place to put the contents of your Disk Array's shipping container on. Altogether, you should find the following items in the package : The Disk Array One AC power cord One External SCSI cable Keys ( For HDD Trays ) User Guide Remove all the items from the carton. If anything is missing or broken , please inform your dealer immediately. Save the cartons and packing materials that came with the Disk Array. Use these materials for shipping or transporting the Disk Array. Figure : Checklist 2-2 Getting Started Choosing a place for Disk Array When selecting a place to set up your Disk Array, be sure to follow the guidelines as below: Place on a flat and stable surface. Use a stand that supports at least 50 kgs for this Disk Array. (HDD included ) Place the Disk Array close enough to the computer for the Disk Array's External SCSI cable to reach it. Use a grounded wall outlet. Avoid an electrical outlet controlled by wall switches or automatic timers. Accidental disruption of the power source may wipe out data in the memory of your computer or Disk Array. Keep the entire system away from potential sources of electromagnetic interference, such as loudspeakers , cordless telephones, etc. Caution ! Avoid direct sunlight, excessive heat, moisture, or dust. 2-3 Getting Started Identifying Parts of the Disk Array Front View Figure : Front View 1. LCD Status Display Panel 2. HDD Trays 1 ~ 4 3. Function Keys ( , , Enter , ESC ) 4. Power-On Indicator 5. Host Computer Access Indicator 6. HDD Tray Lock ( Lock / Unlock ) 7. HDD Status Indicator ( Error (Red), Access (Yellow), Power-On (Green) ) 2-4 Getting Started Rear View Figure : Rear View 1. 2. 3. 4. 5. 6. 7. 8. RS232 Adapter ( Terminal Port ) Cooling Fans Power Supply Host channel SCSI adapter Port Fan Door Screws AC Power Source Input Socket AC Voltage Select Switch ( 115V / 230V ) Power Supply Unit Switch ( On / Off ) 2-5 Getting Started Power Source Choosing a Working Voltage The system can run either on AC 115V (+/10%) or AC 230V (+/10%), Slide the AC voltage select switch on the power supply to the correct position which corresponds with the wall outlet supply voltage. Warning ! Wrong AC Voltage input will harm the power supply and cause serious damage to the Disk Array. Figure : Power Source ! This Disk Array must be grounded This Disk Array is supplied with an AC power cord equipped with a 3-wire grounding type plug. This is a safety feature and it is important to only use a 3-wire grounded mains power cord. 2-6 Getting Started Installing the Hard Disk Drives Step 1 : Unlock the HDD tray by turning the Key-lock to the correct position. Step 2 : Gently Pull out the HDD tray. Figure : Installing HDD step 1, 2 2-7 Getting Started Step 3 : Insert HDD into the tray Step 4 : Screw in the hard drive. ( Use the correct size, type and thread ) Step 5 : Cabling, Connect the Data cable and Power cable. Cabling SCREWS SCREWS Figure : Installing HDD step 3, 4, 5 2-8 Getting Started Step 6 : Gently slide in the HDD tray. Step 7 : Lock the HDD tray. When powered on, the Green LED will light up. Figure : Installing HDD step 6, 7 2-9 Getting Started Host Linkage With the HDD(s) installed correctly, you are ready to connect the Disk Array to your Host computer. Use a shielded twisted-pair SCSI cable to connect your Host computer to the Disk Array's built-in 68 pin SCSI adapter port. Connect the Host computer as shown below : SCSI Plug Disk Array Host Computer Figure : Host linkage Caution ! For safety reasons, make sure the Disk Array and Host Computer are turned off when you plug-in the SCSI cable. 2-10 Getting Started Power-On and Self-Test When you connect the Disk Array to the Host computer, You should press the ON/OFF Switch ( o / I ) on the power supply, it will turn the Disk Array system on and the Self-Test will be started automatically. Power Supply's On / Off Switch 2-11 Getting Started LED Display & Function Keys LED Display Shown below is the LED Display. Please refer to the illustration, the LEDs inform you of the Disk Array's current operating status. Upon activating a certain function, the corresponding LED indicator should turn on indicating that the feature is engaged. ESC Enter Figure : LED Display LED Descriptions 1. Power ON Indicator light up : "Green" , it lights when the Power Supply is plugged and operating functionally. 2. Host Computer Access Indicator light up : "Yellow" , Indicates Host computer is currently accessing the Disk Array 3. HDD Power-On Indicator light up : "Green" , It lights when the HDD frame is locked and Power-On HDD Error Indicator 4. HDD Access Indicator light up : "Red" , when the HDD not installed or error. light up : "Yellow" , when HDD is access. 2-12 Getting Started Function Keys The four function keys at the top of the front panel perform the following functions : ) Up Arrow / Right Arrow Use to scroll the cursor Upward / Rightward ) Down Arrow / Left Arrow Use to scroll the cursor Downward / Leftward ( Enter ) Use to confirm a selected item ( ESC ) Use to exit a selection 2-13 Getting Started LCD Status Panel Located the LCD panel, the LCD status panel informs you of the Disk Array's current operating status at a glance. Upon activating a certain function, a symbol or icon corresponding to that function will appear in the display window. The symbol will remain in the display window indicating the status of the Disk Array. Identifying the status on the LCD The following illustration shows the symbols (characters) been used and their representation. A description of each of the symbols in LCD display window : On-line and functional Error occur Identifying Disk Drive Spare Disk Drive Disk Drive not installed Warning : Disk Drive with too many Bad Sectors Example of the LCD status display window : OOSX R5 ID:0 This informs you : a. HDD 1 ~ HDD 2 b. HDD 3 c. HDD 4 d. RAID Level e. SCSI ID On-line It is a Spare disk drive Not installed In " RAID Level 5 " In " ID# 0 " 2-14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 14 Create Date : 2002:03:04 13:49:14 Modify Date : 2002:03:04 13:49:14 Producer : Corel PDF Engine Version 9.397 Author : Y.M. Creator : CorelDRAW Version 9.397 Title : Aiby1400-Ch2.cdrEXIF Metadata provided by EXIF.tools