Maxtronic Co AIBY Disk Array User Manual Aiby1400 Ch4

Download:
Mirror Download [FCC.gov]
Document ID	252952
Application ID	Ftpxe8QiLG2b+ExF5stLCQ==
Document Description	users manual 5
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	113.29kB (1416150 bits)
Date Submitted	2002-06-27 00:00:00
Date Available	2002-06-26 00:00:00
Creation Date	2002-03-04 13:50:00
Producing Software	Corel PDF Engine Version 9.397
Document Lastmod	2002-03-04 13:50:00
Document Title	Aiby1400-Ch4.cdr
Document Creator	CorelDRAW Version 9.397
Document Author:	Y.M.

Chapter 4 : " Advanced Information "
This chapter describes more information about your Disk Array. The
following items are describes in detail.
Memory Expansion
RAID Controller
Updating Firmware
4-1
Advanced Information
Memory Expansion
Your Disk Array comes with 64MB of memory that is expandable
to a maximum of 512MB.
These expansion memory module can be purchased from your
dealer.
Memory Type : 3.3V PC100/133 SDRAM 144pin DIMM.
Memory Size : Supports 144pin DIMMs of 64MB, 128MB, 256MB
or 512MB.
Height : 1.15 Inches ( 29.2 mm ).
64MB
8(8Mx8), 8(4Mx16) or 4(8Mx16)
128MB
16(8Mx8), 8(16Mx8), 8(8Mx16) or 4(16Mx16)
256MB
16(16Mx8), 8(32Mx8) or 8(16Mx16)
512MB
16(32Mx8)
1.15"
(29.2mm)
4-2
Advanced Information
Installing Memory Modules :
1. Unscrew & Remove cover
Unscrews
Figure : Remove Cover
4-3
Advanced Information
2. Install the memory
a. The DIMM memory modules will only fit in one orientation.
b. Press the memory module firmly into socket from a 45 degree
angle, make sure that all the contacts are aligned with the
socket.
c. Push the memory module forward to a horizontal position.
Front Panel
Ultra 2 SCSI Host Channel
Figure : Controller
4-4
Advanced Information
Disk Array Controller Block Diagram
i80303
RISC
Microprocessor
Main
memory
Flash
EPROM
i80303 Local BUS
NVRAM
PCI
Bridge
LCD
RS232
Terminal
Port
PCI BUS
Ultra 2
Wide
SCSI
controller
Host
channel
Dual
Channel
IDE
Dual
Channel
IDE
Controller
Controller
Disk Disk
#1
#2
Disk Disk
#3
#4
4-5
Advanced Information
Updating Firmware
1. Setup your VT100 Terminal
Please configure the VT100 terminal setting to the values shown
below :
VT100 terminal ( or compatible ) set up
Connection
Serial Port ( COM1 or COM2 )
Protocol
RS232 ( Asynchronous )
Cabling
Null-Modem cable
Baud Rate
115,200
Data Bits
Stop Bit
Parity
None
4-6
Advanced Information
Setup VT100 Terminal
Example : Setup VT100 Terminal in Windows
Step 1.
4-7
Advanced Information
Step 2.
4-8
Advanced Information
Step 3. Enter a name for your Terminal.
4-9
Advanced Information
Step 4. Select a connecting port in your Terminal.
4-10
Advanced Information
Step 5. Port parameter settings
4-11
Advanced Information
Step 6.
4-12
Advanced Information
Step 7. Select emulate VT100 mode
After you have finished the VT100 Terminal setup, you may restart
your Disk Array and press " Ctrl + D " keys ( in your Terminal )to link
the Disk Array and Terminal together.
Press
Ctrl
to display the disk array Monitor Utility
screen on your VT100 Terminal.
4-13
Advanced Information
Start to Update Firmware
1. Move the cursor to " Update ROM " and press "Enter".
Warning !
Unpredictable results will occur if firmware update is attempted
during Host computer and Disk Array activity. All activity to the
controller should be stopped before updating firmware.
4-14
Advanced Information
2. Press " Y " to download the new firmware and
press " Y " again to confirm the Update.
4-15
Advanced Information
3. Select transfer " Send Text File " and press Enter.
4-16
Advanced Information
4. Locate the new Firmware file on your PC.
4-17
Advanced Information
5. Press " Go " to confirm to download the new firmware.
4-18
Advanced Information
6. Type " Go " to reconfirm and the firmware will begin to be
reprogrammed.
7. After verifying, please restart the Disk Array to activate the
new firmware.
4-19

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 19
Create Date                     : 2002:03:04 13:50:00
Modify Date                     : 2002:03:04 13:50:00
Producer                        : Corel PDF Engine Version 9.397
Author                          : Y.M.
Creator                         : CorelDRAW Version 9.397
Title                           : Aiby1400-Ch4.cdr

EXIF Metadata provided by EXIF.tools