Maxtronic Co SILVERII Disk Array System User Manual users manual part3

Download:
Mirror Download [FCC.gov]
Document ID	112652
Application ID	OqVRlOwpvPql5J4VVs1e9Q==
Document Description	users manual part3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	194.9kB (2436229 bits)
Date Submitted	2000-08-10 00:00:00
Date Available	2000-08-28 00:00:00
Creation Date	2000-08-02 17:19:28
Producing Software	Acrobat 4.0 Import Plug-in for Windows
Document Lastmod	2000-08-03 15:02:18
Document Title	users manual part3
Document Creator	Acrobat 4.0 Import Plug-in for Windows

Getting Started
Power Source
Choosing a Working Voltage
The system can run either on AC 115V(+/10%) or AC 230V
(+/i 0%], Slide the AC voltage select switch on both of the two
power supply units to The correct position which corresponds
with the wall outlet supply voltage.
Wrong AC Voltage input will harm the power supply and
cause serious damage to the Disk Array.
o mmm°= "El
"EL—JE-
mu g;-
power cord equipped with
a 3-wire grounding type plug. This Is a safety feature and it is
important to only use a 3—wire grounded mains power cord.
Getting Started
Hard Disk Drives Pre-Setting
1. HDD SCSI Terminator : set " Disable SCSI Terminator ".
Important !
You must set disable SCSI terminator to all of these dr'wes even
it is on the end the device channel bus.
2. Terminator Power : set “ Term. Power from SCSI Bus ",
3. Motor Star option : set " Enable motor start ".
4. Setting the SCSI ID : Pre-settlng is not necessary.
By using the Auto SCSI ID assignment design In thls Disk Array
System, the RAID controller will assign SCSI ID to all of these
dr‘wes automatically when you connected the SCSI ID cable
( on the HDD tray l to these drives
Optional Usage Plug
Figure : Drive Rear Wew
Getting Started
About HDD's Auto SCSI |D# Sefllng
Common optional SCSI ID Usage Plug :
Pin Assignment Pln Signal
119 7 5 3 r 1 A0
3 Al
I: a r: r: D r: 5 A2
D El El El r: I: 7 A3
8 LED Cathode
12108 6 4 2
*** You must check the HDD's Installation guide before you install
the drives, it your drives have not this rear optional usage plug
or the pin assignment ls different from the above common usage
plug, then you must set the HDD's SCSI ID# manually as below :
Trayl :ID#O
Tray 2 : ID#I 12__,
Troy 3 : ID#2 3_.
Troy 4 : ID#3 g—>
, —>
Tray 5 : ID#O 6—>
Tray 6 . ID#I 7__,
Troy 7 : ID#2 B——>
Tray 8 : ID#3
Figure : Manual HDD's SCSI ID setting
Important :
If your drlve's option usage plug or pin assignment is different from
the above, -- Do not connect the SCSI ID cable into the drives,
Getting Sian‘ed
insiolling the Hard Disk Drives
Step 1 : Open The front cover
Figure : Installing HDD step 1
Gettin Started
Step 2 : Unlock the HDD troy by turning the Key-lock to the
correct posltlon.
Step 3 : Gently Pull out the HDD troy.
,,-_.|Q
' announununnmmn “l
l aananununnununu ‘l
I‘L-H“ "usll
'fi .@
——! 3m:
Figure : lnstcllling HDD step 2, 3
Getting Started
Step 4 : Insert HDD into the tray
Step 5 : Screw In the hard drive.
( Use the correct size, type and thread )
Step 6 : Cabling, Connect the Data cable , SCSI ID cable
& Power cable.
m—¢_-— Cabling
SCREWS SCREWS
Figure : Installing HDD step 4, 5, 6

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2000:08:03 15:02:18+08:00
Create Date                     : 2000:08:02 17:19:28+08:00
Creator                         : Acrobat 4.0 Import Plug-in for Windows
Producer                        : Acrobat 4.0 Import Plug-in for Windows
Page Count                      : 6

EXIF Metadata provided by EXIF.tools