Maxtronic Co SILVERWORKII Disk Array (RAIO) User Manual users manual part4

Download:
Mirror Download [FCC.gov]
Document ID	112632
Application ID	MexROdQv5Udhx55fkEsJ8w==
Document Description	users manual part4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	319.95kB (3999325 bits)
Date Submitted	2000-08-10 00:00:00
Date Available	2000-08-25 00:00:00
Creation Date	2000-08-09 11:11:58
Producing Software	Acrobat 4.0 Import Plug-in for Windows
Document Lastmod	2000-08-09 16:01:28
Document Title	users manual part4
Document Creator	Acrobat 4.0 Import Plug-in for Windows

Getting Started
Power Source
Choosing a Working Voltage
The system can run either on AC 110V [+/10%) or AC 220V
(+/lO%], Slide the AC voltage select switch on both of the two
power supply units to the correct position which corresponds
with the wall outlet supply voltage.
War a f
Wrong AC Voltage input will harm the power supply and
cause serious damage to the Disk Array.
This Disk Andy is supplied with an AC power cord equipped with
a 3-wire grounding type plug. This is a safety feature and it is
important to only use a 3-wlre grounded mains power cord.
Getting Started
Hard Disk Drives Pre-Setting
1. HDD SCSI Terminator : se " Disable SCSI Terminator
Important I
You must set disable SCSI terminator to all of these drives even
it Is on the end the device channel bus.
2. Terminator Power : set " Term. Power from SCSI Bus ",
3. Motor Star option : set " Enable motor start ".
4. Setting the SCSI ID : Pre-settlng Is not necessary.
By using the Auto SCSI ID assignment design in this Disk Array
System, the RAID controller will assign SCSI ID to all of these
drives automatically when you connected the SCSI ID cable
I on the HDD tray ) to these drives.
Optional Usage Plug
Figure : Drive Rear Wew
Getting Started
About HDD's Auto SCSI ID# Setting
Common optional SCSI ID Usage Plug :
Pin Assignment
1197531
DDDDDD
EIEIEIDEIEI
12108 6 4 2
Pin
acumen—-
Signal
A0
A1
A2
A3
LED Cathode
*** You must check the HDD‘s installation guide before you install
the drives, if your drives have not this rear optional usage plug
or the pin assignment is different from the above common usage
plug, then you must set the HDD's SCSI ID# manually as below :
Tray 1 :
Tray 2 :
Tray 3 :
Tray 4 :
Tray 5 :
Tray 6 :
Tray 7 :
Tray 8 :
ID#O
ID#]
ID#2
ID#3
ID#O
ID#]
ID#2
ID#3
Important :
Figure : Manual HDD's SCSI ID setting
fyour drive’s option usage plug or pin assignment is different from
the above, -- Do not connect the SCSI ID cable into the drives.
Getting Started
Installing the Hard Disk Drives
Step 1 : Unlock the HDD trcry by turning the Key-look to the
correct position.
Step 2 : Gently Pull out the HDD tray.
Figure : Installing HDD step 1, 2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2000:08:09 16:01:28+08:00
Create Date                     : 2000:08:09 11:11:58+08:00
Creator                         : Acrobat 4.0 Import Plug-in for Windows
Producer                        : Acrobat 4.0 Import Plug-in for Windows
Page Count                      : 4

EXIF Metadata provided by EXIF.tools