Maytel MS-1124G Multicom Stationary 2.4G (MTT Stationary T-1) User Manual 1
Maytel Co., Ltd Multicom Stationary 2.4G (MTT Stationary T-1) 1
Maytel >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3216382 |
| Application ID | NNaphEs956ufShore7/K/w== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 390.61kB (4882631 bits) |
| Date Submitted | 2016-12-02 00:00:00 |
| Date Available | 2016-12-02 00:00:00 |
| Creation Date | 2016-10-25 15:47:54 |
| Producing Software | Adobe PDF library 8.00 |
| Document Lastmod | 2016-11-29 15:16:57 |
| Document Title | 1 |
| Document Creator | Adobe Illustrator CS3 |
MULTICOM STATIONARY 2.4G USER'S MANUAL 1. General Information 1.1 Introduction The "Multicom Stationary 2.4G" is designed by using the most advanced Multiplex communication technology. It serves user-friendly features and extremely convenient to operate including a crystal clear sound quality and also long distance communication coverage. It gives the operation as a central broad cast station to the unlimited number of listeners who carry the MTT-R Receiver devices with them and also provides a communication in full duplex with up to two other users who carry the MTT-T Multicom devices. It is recommendable you read the user's manual thoroughly to enjoy its maximized performance and features this station has to offer. 1.2 Main Features * Audio publishing to the unlimited number of people who carry the MTT-R Receiver * Multiplex communication with up to two other users who carry the MTT-T Multicom devices * Long distance communication coverage over 400m typically * Crystal clear sound quality * 39 different Group selection * Audio output HI/Low selection * Audio volume control with 9 steps * Side tone On/Off selection * Direct microphone sensitivity control with 5 steps * Convenient dual external power supply source either USB plug for the purpose of its portable using by connection Mobile phone Power bank into it or DC 5.0V adapter via AC input 2. Controls and Indicators LCD Down Button Mode Button UP Button Ear / MIC XLR-4PINs (Desk top Mic. IN) Power S.W Antenna Jack USB XLR-3PINs 55 Jack (Audio IN) Power S.W Mode Button Up Button Down Button EAR/MIC XLR-4PINs Antenna Jack USB 55 JACK XLR-3PINs Upward : Power Turn ON / Downward : Power Turn OFF Selection of Group Number, Device ID, Side Tone On/Off, Mute Mode, Microphone Sensitivity level and Audio Output Loud Control to be Up the level in the selected mode Control to be Down the level in the selected mode 3.5mm External Headset Boom Microphone Jack(EHR-01) XLR Headset Jack Long diversity Antenna Jack USB Jack. compatible with Power Bank for mobile phones 55 Jack Audio Output XLR Jack Audio Output 3. How to use 3.1 Power On/Off Press the "Power S.W" switch to the upward to turn the stationary power on. The LCD display is on and shows the default volume level with "VOL 03". If you pressed the "Power S.W" to the downward, the stationary power is turned off. 3.2 Volume Up / Down It gives you to adjust the hearing volume level with 9 steps as per you prefer. Press "▲" button to control volume up and "▼" button for volume down after turn the device power on. It is available to adjust the volume level 0~9 from low to high. Note; The default volume level is 3 and the volume level returns to 3 all the times whenever you power switch turned off and on. 3.3 Group selection Press and hold the "Mode" button longer than 3 seconds after turn the device power on. The "GRP" symbol on the LCD is blinking. Select the Group number 0~39 as you desire by press "▲" or "▼" button and then release all the buttons longer than 5 seconds to fix it. Every radio needs to have a same Group number to communicate each other in a group. Show the selected Group Number "00" Show the selected Group Number "01" 3.4 ID selection In a group, every Stationary needs to have each different ID per Stationary from "00" to "99". The ID "00" becomes a master device in a group and every group needs to have a master device with ID "00" per group without alternative. The "MASTER" is displaying on the LCD as soon as the ID "00" is set. Press and hold the "Mode" button longer than 3 seconds after turn the device power on. The "GRP" symbol on the LCD is blinking. And press the "Mode" button one more time instantly. The "ID" symbol on the LCD is blinking. Select each different ID number per Stationary from "00" to "99" in a group by press "▲" or "▼" button and then release all the buttons longer than 5 seconds to fix it. Display for the Master Display example for the Slave If you have any other Multicom who want to communicate with Stationary in full duplex, you need to set the group number as the same group number as the Stationary has and also set the different ID number than the Stationary set. For the listener who has the MTT-R, it is only required to set the same group number as the Stationary has regardless its ID. 3.5 Audio Output mode High / Low It serves you to choose higher audio output or lower beside of Volume Up / Down. The higher audio output is effective when you listen to the device at the heavy noise place. Press and hold the "Mode" button longer than 3 seconds after turn the device power on. The "GRP" is blinking on the LCD. Press the "Mode" button 6 times instantly. Select either "UH" for higher audio output or "UL" for lower audio output by press "▲" or "▼" button and then release all the buttons longer than 5 seconds to fix it. Normal Audio Output mode Loud Audio Output mode Note; 1) Its default setting is "UL". 2) There might be a kind of white noise creation when you set the audio output at "UH". Hence, it is recommendable to set the audio output at "UL" except using the device at the heavy noise surround place. It is available to select the microphone sensitivity up to 5 steps according to the environment you have. Press and hold the "Mode" button longer than 3 seconds after turn the device power on. The "GRP" is blinking on the LCD. Press the "Mode" button 5 times instantly. Select the microphone sensitivity level 1 ~ 5 as per you desire by press "▲" or "▼" button and then release all the buttons longer than 5 seconds to fix it. Note; 1) The "C 1" is the lowest microphone sensitivity level and "C 5" is the highest. 2) Its default setting is "C 1". 3.7 Portable using It is available to use the Stationary as a portable device rather than the fixed station. Please connect the Power bank for Mobile phone into the USB port of Stationary. After that, place the stationary wherever you prefer 4. Specifications ITEM SPECIFICATION Radio Frequency Type ISM 2405MHz ~ 2477MHz Type Wireless Microphone/Receiver Unit Radio Interface ISM 2.4GHz: FSK Modulation with Frequency Hopping Voice Codec 16bit/8KHz Tx Max. Output Power 10dBm RX Sensitivity -95dBm Voice Latency <35ms Num. of Frequency Channel 145CH Operation Hopping 16CH Channel Spacing 0.5MHz Data Rate 0.5Mbps Freq. Bandwidth 2MHz Power Supply Output Voltage: DC 5.0V Antenna Type Dipole Antenna (Reverse SMA type) Antenna Gain 5.0dBi Power Consumption Avg. 180mA Distance Range(LOS) 200M Frequency response 50Hz ~ 4KHz ▶ The antenna is not standard type, that is special reverse-type. So the using antenna can’t be replace by user easily. 5. How to install 5.1 General Publishing Speaking only or Speaking and Listening 100~ 400m distance Unlimited Listeners with MTT-R Notice) It is required to tune the same group number only between Stationary and MTT-R Listening device regardless its ID number. 5.2 Full duplex communication with up to two other MTT-T devices Stationary MTT-T 1 100~ 400m distance MTT-T 2 Notice) It is required to tune the same group number between Stationary and two other MTT-T devices. Also, the two other MTT-T devices should have each different ID per device except the ID "00" of Stationary owned. 5.3 Full duplex communication and general publishing Stationary MTT-T 1 MTT-T 2 Full Duplex communications between Stationary, MTT-T1 and MTT-T2 Listening all the talking between Stationary, MTT-T1 and MTT-T2 Unlimited number of Listeners with MTT-R 5.4 Line repeat communication between Stationary and Stationary It is available to repeat the communication in one Stationary to the other Stationary by cable connection between two stationeries. Please connect to two XLR 3 port of Stationeries by using "XLR Repeater only cable". Notice; It is required to keep a distance longer than 10m at least between Stationary and Stationary. Otherwise, it might cause the interference each other and the drop of performance on both stationeries. FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected. • Consult the dealer or an experienced radio/TV technician for help. Caution Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation IMPORTANT NOTE: FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antennas used for this transmitter must be installed to provide a separation distance of at least 20Cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this equipment near water. 6) Do not using near any heat sources such as radiators, heat resisters, stove, or other equipment that produce heat. European CE notice to users and product statements This product is CE marked according to the provisions of the R&TTE Directive(1999/5/EC). Hereby, Maytel Co., Ltd declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For further information, please contact http:// www.maytel.com Maytel Co., Ltd #417 Doosan Venture Digm 126-1, Pyeongchon-dong, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea Tel: +82-31-478-5508 Fax: +82-31-440-9331 URL: www.maytel.com CONTACT INFORMATION Manufacturer Address #417 Doosan Venture Digm 126-1, Pyeongchon-dong, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea To locate in-country MAYTEL CO., LTD., distributors of the Multicom Stationary 2.4G (MTT Stationary T-1) please refer to the MAYTEL CO., LTD. Website http:// www.maytel.com These distributor(s) represent local contacts for this product. CORPORATE HEADQUARTERS: MAYTEL CO., LTD. #417 Doosan Venture Digm 126-1, Pyeongchon-dong, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea Tel: +82-31-478-5508 Fax: +82-31-440-9331 Web: http:// www.maytel.com This device complies with Industry Canada license-exempt RSS standard(s). Operation is Subject to the following two condition: (1) this device may not cause interference ,and (2) this device must accept any interference, including interference that may cause undesired operation of the device. EUROPEAN UNION “DECLARATION OF CONFORMITY” DECLARATION OF CONFORMITY MAYTEL CO., LTD. #417 Doosan Venture Digm 126-1, Pyeongchon-dong, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea declare under our sole responsibility that the product(s) Multicom Stationary 2.4G (MTT Stationary T-1) – MS-11 2.4G to which this declaration relate(s) is in conformance with the following standards: EN 301 489-1 V1.9.2:2011 EN 301 489-17 V2.2.1:2012 EN 60950-1:2006/A2:2013 EN 300 328 V1.9.1:2015 following the provisions of the 1999/5/EC Directives.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2016:10:25 15:47:54+09:00 Creator : Adobe Illustrator CS3 Modify Date : 2016:11:29 15:16:57+09:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2016:11:29 15:16:57+09:00 Creator Tool : Adobe Illustrator CS3 Format : application/pdf Title : 1 Document ID : uuid:c5a19dcf-fd4d-43d4-9c92-dc9ee64333bc Instance ID : uuid:efbacb39-bab0-481c-ab9b-80a5d5859f2b Producer : Adobe PDF library 8.00 Page Count : 13EXIF Metadata provided by EXIF.tools