Meet RF005 2.4GHz Wireless Module User Manual MS RF005
Meet (China) Ltd. 2.4GHz Wireless Module MS RF005
Meet >
user manual
MS-RF005 Series User Manual Product: 2.4GHz PC Wireless Module Model: MS-RF005 Series General Description: MS-RF005 under is a digital wireless RF2.4G module, The RF IC is a low-power, high-integrated single chip RF transceiver using 0.18μm mixed-mode CMOS process optimized for ISM 2.4GHz wireless systems. MS-RF005 contains receiver, transmitter, voltage-controlled oscillator (VCO) and phase-locked loop (PLL). The device is expressly designed for low power consumption. Specific expertise has been applied to save current consumption and thus to extend the battery life, which is of most importance to the portable wireless consumer applications. Power saving mode has also been implemented to further reduce the power consumption. The receiver contains a low-noise amplifier (LNA), a high-frequency mixer, a received signal strength indicator (RSSI), a channel select filter, a limiting amplifier, a demodulator and a data slicer with clock recovery. MS-RF005 have antenna in PCB. Transmission power: 0dBm (1mW) . And Transmission Distance is 0 ~ 20m. The module have receive and transmit function, sleep function. Output power, transmit-receive mode and communications channels can be programmed through the SPI interface to control. Applications: - Industrial equipment Communicate - Wireless Mouse, Presenters, Keyboards and Game pad - Wireless VOIP and Headsets - Remote Controls - Toys - Home Automation - Consumer Electronics Features: 2.4GHz GFSK RF transceiver - Operates in unlicensed worldwide Industrial, Science and Medical (ISM) band(2.401GHz~2.479GHz) - Sensitively up to –93 dBm - Output power up to 0 dBm - Low-noise amplifier, power amplifier, modern and data slicer/recovery on chip - Low operation voltage from 1.9V to 3.6V - Low current consumption, 8.2mA@-20dBm at TX mode and 18mA at RX mode - Programmable 250kbps/1Mbps transfer bit-rate Configurable preamble, scramble, source address, Page 1 of 5 destination address and CRC generation Programmable data payload length from 1-byte to 32-byte - 3-wire SPI interface for device configuration - Complete RSSI function on chip - Operation temperature range from –40 °C to +85°C MS-RF005 size and pin diagram: Page 2 of 5 Pin Description: Pin No Pin Name I/O Active State PSB Low Digital input. Assert to force MS-RF005 to enter Power-Saving Mode or Power-Down Mode, depended on the state of TRRDY. TRINT High Digital output. Asserted when transmitting or receiving is accomplished. TRRDY High Digital input. Assert to set the MS-RF005 to Active Mode. Description TRSCLK I/O N/A Digital input at Burst Mode and digital output at Direct Mode.Clock signal of the SPI/FIFO interface. TRSDAT N/A Digital input/output. Data signal of the SPI/FIFO interface. SPIEN High Digital input. Enable signal of the SPI interface. GND N/A Ground. VCC N/A Digital power pin. +3.3VDC. Electrical Specifications: Absolute Maximum Ratings Page 3 of 5 Recommend Operating Conditions: DC Electrical Characteristics Page 4 of 5 IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Declaration the Restriction of this Limited Module Approval: According to FCC Part 15 Subpart C Section 15.212, the radio elements of the modular transmitter must have their own shielding. However, due to there is no shielding for this RF GFSK Module, this module is granted as a Limited Modular Approval. Due to missing shielding the module is strictly limited to integration by the Grantee himself or his dedicated OEM Integrator. USER MANUAL OF THE END PRODUCT: In the user manual of the end product, the end user has to be informed that the equipment complies with FCC radio-frequency exposure guidelines set forth for an uncontrolled environment. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the user manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following" Contains TX FCC ID: AZK-RF005 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 0700 Page 5 of 5
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2012:03:20 16:13:48+08:00 Create Date : 2012:03:20 16:13:48+08:00 Format : application/pdf Title : Microsoft Word - MS-RF005 User Manual.doc Creator : Administrator Document ID : uuid:0e100867-0036-4070-ac05-c215340ae8bc Instance ID : uuid:8fc7717b-c7e3-494c-8c1a-4971d9e1d2e9 Page Count : 5 Author : AdministratorEXIF Metadata provided by EXIF.tools