Mertik Maxitrol and KG B6R Handset of remote electronic ignition and control system for gas applications User Manual GV60 symax II OI EN 28 10 2013 Draft indd

Mertik Maxitrol GmbH & Co. KG Handset of remote electronic ignition and control system for gas applications GV60 symax II OI EN 28 10 2013 Draft indd

UserManual.wiki >

Mertik Maxitrol and KG >

B6R User Manual >

Instructions part 2

Contents

Instructions part 2

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.16 / 28SETTING CELSIUS OR FAHRENHEIT1 2ONAMPMOFFTo change between °C and °F, press and buttons simultaneously.NOTE: Choosing °F results in a 12 hour clock. Choosing °C results in a 24 hour clock.SETTING THE TIME1 2ONAMPMOFF1. Press and buttons simultane-ously. Hour ﬂ ashes.2. To select hour press or button.3. Press and buttons simultane-ously. Minutes ﬂ ash.4. To select minutes press or but-ton.5. To conﬁ rm press and buttons simultaneously or wait.MODES OF OPERATION1 2ONAMPMOFFEnter Mode Press the appropriate mode button. Exit Mode1. Press the same mode button again to change to Manual mode.2. Press or button to change to Manual mode.3. Press a different mode button to change to that mode.1 2ONAMPMOFFThermostatic Mode The room temperature is measured and compared to the set temperature. The ﬂ ame height is then automatically ad-justed to achieve the set temperature.1 2ONAMPMOFFProgram Mode Programs 1 and 2, each can be pro-grammed to go ON and OFF at speciﬁ c times at a set temperature. 6-SYMBOLFigure 21: 6-symbol DisplayProgram ModeTemperatureTimeCountdown TimerBattery StatusSignal Indicator Child ProofThermostatic Mode1 2ONAMPMOFF°F or °C

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.17 / 286-SYMBOLMANUAL MODE (HANDSET)NOTICEBEFORE OPERATING1. Make sure MANUAL knob on the GV60 Valve is in the ON, full counterclockwise position. 2. Place the ON/OFF switch (if equipped) in the “I” (ON position).TO TURN ON FIRE When pilot ignition is conﬁ rmed, motor turns automatically to maximum ﬂ ame height.1 2ONAMPMOFFHandset▪ Press button until a short beep con-ﬁ rms the start sequence has begun; release button. ▪ Continuing beeps conﬁ rm ignition is in process.▪ Rotating circle is shown on display un-til ignition sequence is complete.▪ There is main gas ﬂ ow once pilot igni-tion is conﬁ rmed.▪ Handset automatically goes into Man-ual mode after main burner ignition.If the pilot does not stay lit after several tries, turn the main valve knob to OFF and follow the instructions “TURN OFF GAS TO APPLIANCE” (page 28).Standby Mode (Pilot Flame)Handset▪ Press and hold button to set appliance to pilot ﬂ ame.TO TURN OFF FIRE1 2ONAMPMOFFHandset▪ Press button to turn off.NOTE: There is a 5 sec delay before the next ignition is possible.FLAME HEIGHT ADJUSTMENT1 2ONAMPMOFFHandset▪ To increase ﬂ ame height press and hold button.▪ To decrease ﬂ ame height or to set ap-pliance to pilot ﬂ ame, press and hold button.DESIGNATED LOW FIRE AND HIGH FIREAM▪ To go to low ﬁ re, double-click but-ton. “LO” is displayed.NOTE: Flame goes to high ﬁ re ﬁ rst be-fore going to low ﬁ re.AM▪ To go to high ﬁ re, double-click but-ton. “HI” is displayed.If the appliance will not operate, follow the instructions “TURN OFF GAS TO APPLIANCE” (page 28).THERMOSTATIC MODE1 2ONAMPMOFFON: Press button. Thermostat icon dis-played, preset temperature displayed brieﬂ y, and then room temperature dis-played.OFF: 1. Press button.2. Press or button to enter Manual mode.3. Press button to enter Countdown Timer mode.1 2ONAMPMOFFSETTING: 1. Press button and hold until Ther-mostat icon displayed, temperature ﬂ ashes.2. To adjust SET temperature press or button.3. To conﬁ rm press button or wait.

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.18 / 281 2ONAMPMOFFTime SETTING: 1. Press button and hold until , , displayed, hour ﬂ ashes.2. To select hour press or button.3. To conﬁ rm press button. , dis-played, minutes ﬂ ash.4. To select minutes press or but-ton.1 2ONAMPMOFF5. To conﬁ rm press button. , , displayed, hour ﬂ ashes.6. To select hour, press or button.7. To conﬁ rm press button. , , displayed, minutes ﬂ ash.8. To select minutes press or but-ton.NOTE: If you stop programming at this point, program 2 remains deactivated.NOTE: Programs 1 and 2 use the same ON (Thermostatic) and OFF temperatures.1 2ONAMPMOFF1. To continue to program , press button. , , displayed, hour ﬂ ashes.2. To select hour press or button.3. To conﬁ rm press button. , , displayed, minutes ﬂ ash.4. To select minutes, press or but-ton.5. To conﬁ rm press button. , , displayed, hour ﬂ ashes.6. To select hour, press or button.7. To conﬁ rm press button. , , displayed, minutes ﬂ ash. 8. To select minutes, press or but-ton. 9. To conﬁ rm press button or wait.NOTE: Programs and use the same ON and OFF tempera-tures. Once an ON and/or OFF temperature has been set, that temperature becomes the new default setting.CHILD PROOF1 2ONAMPMOFFON: To activate press and buttons si-multaneously. Children icon displayed and the handset is rendered inoper-able, except for the OFF function.OFF: To deactivate press and buttons simultaneously. Children icon disap-pears.COUNTDOWN TIMER1 2ONAMPMOFFON/SETTING: 1. Press and hold button until hour-glass icon displayed and hour ﬂ ashes. 2. To select hour press or button.3. To conﬁ rm press button. Minutes ﬂ ash.4. To select minutes press or button.5. To conﬁ rm press button or wait.OFF: Press button, hourglass and count-down time disappear.NOTE: At end of countdown time period, the ﬁ re turns OFF. The CountdownTimer only works in Manual, Thermostatic, and Random modes. Maximum countdown time is 9 hours.PROGRAM MODENOTE: The set temperature for Thermostatic Mode is the tem-perature for the ON time in Program Mode. Changing the Thermostatic Mode set temperature also changes the ON time temperature in Program Mode.1 2ONAMPMOFFON: Press button. , or , ON or OFF displayed. 1 2ONAMPMOFFOFF: 1. Press or or button to enter Manual mode.2. Press button to enter Thermostatic mode.3. Press Random icon button to enter Random mode.1 2ONAMPMOFFPROGRAM Temperature SETTING: 1. Press button and hold until , , Set temperature (Thermostatic) displayed.2. To continue press button. , displayed, temperature ﬂ ashes and wait.3. To select OFF temperature press or button.4. To conﬁ rm press button or wait.NOTE: The ON (Thermostatic) and OFF set temperatures are the same for each day.Program Mode

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.19 / 281 2ONAMPMOFFSETTING CELSIUS OR FAHRENHEIT1 2ONAMPMOFFTo change between °C and °F, press and buttons simultaneously.NOTE: Choosing °F results in a 12 hour clock. Choosing °C results in a 24 hour clock.SETTING THE TIME1 2ONAMPMOFF1. Press and buttons simultane-ously. Hour ﬂ ashes.2. To select hour press or button.3. Press and buttons simultane-ously. Minutes ﬂ ash.4. To select minutes press or but-ton.5. To conﬁ rm press and buttons simultaneously or wait.MODES OF OPERATION1 2ONAMPMOFFEnter Mode Press the appropriate mode button. Exit Mode1. Press the same mode button again to change to Manual mode.2. Press or button to change to Manual mode.3. Press a different mode button to change to that mode.1 2ONAMPMOFFThermostatic Mode The room temperature is measured and compared to the set temperature. The ﬂ ame height is then automatically ad-justed to achieve the set temperature.1 2ONAMPMOFFProgram Mode Programs 1 and 2, each can be pro-grammed to go ON and OFF at speciﬁ c times at a set temperature. 8-SYMBOLFigure 22: 8-symbol DisplayProgram ModeTemperatureTimeAuxiliary FeatureCountdown TimerBattery StatusSignal Indicator Child ProofRandom ModeThermostatic Mode°F or °C 8-SYMBOL

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.20 / 28AMRandom ModeFlame height changes automatically.NOTE: Mains adapter recommended. MANUAL MODE (HANDSET)NOTICEBEFORE OPERATING1. Make sure MANUAL knob on the GV60 Valve is in the ON, full counterclockwise position. 2. Place the ON/OFF switch (if equipped) in the “I” (ON position).TO TURN ON FIRE When pilot ignition is conﬁ rmed, motor turns automatically to maximum ﬂ ame height.1 2ONAMPMOFFHandset▪ Press button until a short beep con-ﬁ rms the start sequence has begun; release button. ▪ Continuing beeps conﬁ rm ignition is in process.▪ Rotating circle is shown on display un-til ignition sequence is complete.▪ There is main gas ﬂ ow once pilot igni-tion is conﬁ rmed.▪ Handset automatically goes into Man-ual mode after main burner ignition.If the pilot does not stay lit after several tries, turn the main valve knob to OFF and follow the instructions “TURN OFF GAS TO APPLIANCE” (page 28).Standby Mode (Pilot Flame)Handset▪ Press and hold button to set appliance to pilot ﬂ ame.TO TURN OFF FIRE1 2ONAMPMOFFHandset▪ Press button to turn off.NOTE: There is a 5 sec delay before the next ignition is possible.FLAME HEIGHT ADJUSTMENT1 2ONAMPMOFFHandset▪ To increase ﬂ ame height press and hold button.▪ To decrease ﬂ ame height or to set ap-pliance to pilot ﬂ ame, press and hold button.DESIGNATED LOW FIRE AND HIGH FIREAM▪ To go to low ﬁ re, double-click but-ton. “LO” is displayed.NOTE: Flame goes to high ﬁ re ﬁ rst be-fore going to low ﬁ re.AM▪ To go to high ﬁ re, double-click but-ton. “HI” is displayed.If the appliance will not operate, follow the instructions “TURN OFF GAS TO APPLIANCE” (page 28).

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.21 / 281 2ONAMPMOFFOFF: 1. Press or or button to enter Manual mode.2. Press button to enter Thermostatic mode.3. Press Random icon button to enter Random mode.1 2ONAMPMOFFPROGRAM Temperature SETTING: 1. Press button and hold until , , Set temperature (Thermostatic) displayed.2. To continue press button. , displayed, temperature ﬂ ashes and wait.3. To select OFF temperature press or button.4. To conﬁ rm press button or wait.NOTE: The ON (Thermostatic) and OFF set temperatures are the same for each day.1 2ONAMPMOFFTime SETTING: 1. Press button and hold until , , displayed, hour ﬂ ashes.2. To select hour press or button.3. To conﬁ rm press button. , dis-played, minutes ﬂ ash.4. To select minutes press or but-ton.1 2ONAMPMOFF5. To conﬁ rm press button. , , displayed, hour ﬂ ashes.6. To select hour, press or button.7. To conﬁ rm press button. , , displayed, minutes ﬂ ash.8. To select minutes press or but-ton.NOTE: If you stop programming at this point, program 2 remains deactivated.NOTE: Programs 1 and 2 use the same ON (Thermostatic) and OFF temperatures.THERMOSTATIC MODE1 2ONAMPMOFFON: Press button. Thermostat icon dis-played, preset temperature displayed brieﬂ y, and then room temperature dis-played.OFF: 1. Press button.2. Press or button to enter Manual mode.3. Press button to enter Countdown Timer mode.4. Press button to enter Random mode.1 2ONAMPMOFFSETTING: 1. Press button and hold until Ther-mostat icon displayed, temperature ﬂ ashes.2. To adjust SET temperature press or button.3. To conﬁ rm press button or wait.COUNTDOWN TIMER1 2ONAMPMOFFON/SETTING: 1. Press and hold button until hour-glass icon displayed and hour ﬂ ashes. 2. To select hour press or button.3. To conﬁ rm press button. Minutes ﬂ ash.4. To select minutes press or but-ton.5. To conﬁ rm press button or wait.OFF: Press button, hourglass and count-down time disappear.NOTE: At end of countdown time period, the ﬁ re turns OFF. The CountdownTimer only works in Manual, Thermostatic, and Random modes. Maximum countdown time is 9 hours.PROGRAM MODENOTE: The set temperature for Thermostatic Mode is the tem-perature for the ON time in Program Mode. Changing the Thermostatic Mode set temperature also changes the ON time temperature in Program Mode.1 2ONAMPMOFFON: Press button. , or , ON or OFF displayed. 8-SYMBOL

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.22 / 28CHILD PROOF1 2ONAMPMOFFON: To activate press and buttons si-multaneously. Children icon displayed and the handset is rendered inoper-able, except for the OFF function.OFF: To deactivate press and buttons simultaneously. Children icon disap-pears.1 2ONAMPMOFF1. To continue to program , press button. , , displayed, hour ﬂ ashes.2. To select hour press or button.3. To conﬁ rm press button. , , displayed, minutes ﬂ ash.4. To select minutes, press or but-ton.5. To conﬁ rm press button. , , displayed, hour ﬂ ashes.6. To select hour, press or button.7. To conﬁ rm press button. , , displayed, minutes ﬂ ash. 8. To select minutes, press or but-ton. 9. To conﬁ rm press button or wait.NOTE: Programs and use the same ON and OFF tempera-tures. Once an ON and/or OFF temperature has been set, that temperature becomes the new default setting.RANDOM FLAMEAMON: Press button. Random icon dis-played.OFF: Press button. Random icon disap-pears.NOTE: Mains adapter recommended. AUXILIARY FEATUREUpon ignition burner 1 is ON and burner 2 is in the last setting.1 2ONAMPMOFFOFF: To switch the burner OFF, press the button (Auxiliary icon disappears).ON: To switch a burner ON, press the but-ton.NOTE: The latching solenoid valve cannot operate manually. If the receiver battery runs down it will remain in the last operating position. Program Mode

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.23 / 28SETTING CELSIUS OR FAHRENHEIT1 2ONAMPMOFFTo change between °C and °F, press and buttons simultaneously.NOTE: Choosing °F results in a 12 hour clock. Choosing °C results in a 24 hour clock.SETTING THE TIME1 2ONAMPMOFF1. Press and buttons simultane-ously. Hour ﬂ ashes.2. To select hour press or button.3. Press and buttons simultane-ously. Minutes ﬂ ash.4. To select minutes press or but-ton.5. To conﬁ rm press and buttons simultaneously or wait.MODES OF OPERATION1 2ONAMPMOFFEnter Mode Press the appropriate mode button. Exit Mode1. Press the same mode button again to change to Manual mode.2. Press or button to change to Manual mode.3. Press a different mode button to change to that mode.1 2ONAMPMOFFThermostatic Mode The room temperature is measured and compared to the set temperature. The ﬂ ame height is then automatically ad-justed to achieve the set temperature.1 2ONAMPMOFFProgram Mode Programs 1 and 2, each can be pro-grammed to go ON and OFF at speciﬁ c times at a set temperature. 10-SYMBOLFigure 23: 10-symbol DisplayLightFanProgram ModeTemperatureTimeAuxiliary FeatureCountdown TimerBattery StatusSignal Indicator Child ProofRandom ModeThermostatic Mode1 2ONAMPMOFF°F or °C 10-SYMBOL

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.24 / 28AMRandom ModeFlame height changes automatically.NOTE: Mains adapter recommended. MANUAL MODE (HANDSET)NOTICEBEFORE OPERATING1. Make sure MANUAL knob on the GV60 Valve is in the ON, full counterclockwise position. 2. Place the ON/OFF switch (if equipped) in the “I” (ON position).TO TURN ON FIRE When pilot ignition is conﬁ rmed, motor turns automatically to maximum ﬂ ame height.1 2ONAMPMOFFHandset▪ Press button until a short beep con-ﬁ rms the start sequence has begun; release button. ▪ Continuing beeps conﬁ rm ignition is in process.▪ Rotating circle is shown on display un-til ignition sequence is complete.▪ There is main gas ﬂ ow once pilot igni-tion is conﬁ rmed.▪ Handset automatically goes into Man-ual mode after main burner ignition.If the pilot does not stay lit after several tries, turn the main valve knob to OFF and follow the instructions “TURN OFF GAS TO APPLIANCE” (page 28).Standby Mode (Pilot Flame)Handset▪ Press and hold button to set appliance to pilot ﬂ ame.TO TURN OFF FIRE1 2ONAMPMOFFHandset▪ Press button to turn off.NOTE: There is a 5 sec delay before the next ignition is possible.FLAME HEIGHT ADJUSTMENT1 2ONAMPMOFFHandset▪ To increase ﬂ ame height press and hold button.▪ To decrease ﬂ ame height or to set ap-pliance to pilot ﬂ ame, press and hold button.DESIGNATED LOW FIRE AND HIGH FIREAM▪ To go to low ﬁ re, double-click but-ton. “LO” is displayed.NOTE: Flame goes to high ﬁ re ﬁ rst be-fore going to low ﬁ re.AM▪ To go to high ﬁ re, double-click but-ton. “HI” is displayed.If the appliance will not operate, follow the instructions “TURN OFF GAS TO APPLIANCE” (page 28).

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.25 / 281 2ONAMPMOFFOFF: 1. Press or or button to enter Manual mode.2. Press button to enter Thermostatic mode.3. Press Random icon button to enter Random mode.1 2ONAMPMOFFPROGRAM Temperature SETTING: 1. Press button and hold until , , Set temperature (Thermostatic) displayed.2. To continue press button. , displayed, temperature ﬂ ashes and wait.3. To select OFF temperature press or button.4. To conﬁ rm press button or wait.NOTE: The ON (Thermostatic) and OFF set temperatures are the same for each day.1 2ONAMPMOFFTime SETTING: 1. Press button and hold until , , displayed, hour ﬂ ashes.2. To select hour press or button.3. To conﬁ rm press button. , dis-played, minutes ﬂ ash.4. To select minutes press or but-ton.1 2ONAMPMOFF5. To conﬁ rm press button. , , displayed, hour ﬂ ashes.6. To select hour, press or button.7. To conﬁ rm press button. , , displayed, minutes ﬂ ash.8. To select minutes press or but-ton.NOTE: If you stop programming at this point, program 2 remains deactivated.NOTE: Programs 1 and 2 use the same ON (Thermostatic) and OFF temperatures.THERMOSTATIC MODE1 2ONAMPMOFFON: Press button. Thermostat icon dis-played, preset temperature displayed brieﬂ y, and then room temperature dis-played.OFF: 1. Press button.2. Press or button to enter Manual mode.3. Press button to enter Countdown Timer mode. 4. Press button to enter Random mode.1 2ONAMPMOFFSETTING: 1. Press button and hold until Ther-mostat icon displayed, temperature ﬂ ashes.2. To adjust SET temperature press or button.3. To conﬁ rm press button or wait.COUNTDOWN TIMER1 2ONAMPMOFFON/SETTING: 1. Press and hold button until hour-glass icon displayed and hour ﬂ ashes. 2. To select hour press or button.3. To conﬁ rm press button. Minutes ﬂ ash.4. To select minutes press or but-ton.5. To conﬁ rm press button or wait.OFF: Press button, hourglass and count-down time disappear.NOTE: At end of countdown time period, the ﬁ re turns OFF. The CountdownTimer only works in Manual, Thermostatic, and Random modes. Maximum countdown time is 9 hours.PROGRAM MODENOTE: The set temperature for Thermostatic Mode is the tem-perature for the ON time in Program Mode. Changing the Thermostatic Mode set temperature also changes the ON time temperature in Program Mode.1 2ONAMPMOFFON: Press button. , or , ON or OFF displayed. 10-SYMBOL

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.26 / 28RANDOM FLAMEAMON: Press button. Random icon dis-played.OFF: Press button. Random icon disap-pears.NOTE: Mains adapter recommended. AUXILIARY FEATUREUpon ignition burner 1 is ON and burner 2 is in the last setting.1 2ONAMPMOFFOFF: To switch the burner OFF, press the button (Auxiliary icon disappears).ON: To switch a burner ON, press the but-ton.NOTE: The latching solenoid valve cannot operate manually. If the receiver battery runs down it will remain in the last operating position. CHILD PROOF1 2ONAMPMOFFON: To activate press and buttons si-multaneously. Children icon displayed and the handset is rendered inoper-able, except for the OFF function.OFF: To deactivate press and buttons simultaneously. Children icon disap-pears.1 2ONAMPMOFF1. To continue to program , press button. , , displayed, hour ﬂ ashes.2. To select hour press or button.3. To conﬁ rm press button. , , displayed, minutes ﬂ ash.4. To select minutes, press or but-ton.5. To conﬁ rm press button. , , displayed, hour ﬂ ashes.6. To select hour, press or button.7. To conﬁ rm press button. , , displayed, minutes ﬂ ash. 8. To select minutes, press or but-ton. 9. To conﬁ rm press button or wait.NOTE: Programs and use the same ON and OFF tempera-tures. Once an ON and/or OFF temperature has been set, that temperature becomes the new default setting.CIRCULATING FAN OPERATIONAM NOTE: SETTING only. Fan is switched ON automatically when gas opens. Circulating fan has 4 speed levels from low (1 bar) to high (4 bars).SETTING: 1. Press button and hold until fan icon ﬂ ashes.2. Press button to increase fan speed and button to decrease fan speed.3. To conﬁ rm setting either press but-ton or wait (Fan icon displayed). OFF: Press button until all 4 speed level bars disappear.LIGHT/DIMMER OPERATIONAMON: Press button (light icon displayed). Light is on at preset level.OFF: Press button (light icon disappears). SETTING: 1. Press button and hold until light icon ﬂ ashes.2. To adjust light between 20…100 % press or button. 3. To conﬁ rm setting either press but-ton or wait (Light icon displayed).NOTE: The Light works independently of the Pilot ﬂ ame. If you want the light ON but no ﬂ ame, press button.

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.27 / 28TOUCH PAD / WALL SWITCHTo Turn ON Appliance ▪ Press button (see ﬁ gure 24) until a short beep con-ﬁ rms the start sequence has begun; release button.▪ Continuing beeps conﬁ rm the ignition is in process.▪ Once pilot ignition is conﬁ rmed, there is main gas ﬂ ow.If the pilot does not stay lit after several tries, turn the main valve knob to OFF and follow the instructions “TO TURN OFF GAS TO APPLIANCE” (page 28).STANDBY MODE (PILOT FLAME)▪ Press and hold (small ﬂ ame) button to set appliance at pilot ﬂ ame.To Turn OFF Appliance▪ Press button.Flame Height Adjustment▪ Press and hold (large ﬂ ame) button to increase ﬂ ame height.▪ Press and hold (small ﬂ ame) button to decrease ﬂ ame height or to set appliance at pilot ﬂ ame.▪ For ﬁ ne adjustment tap (large ﬂ ame) or (small ﬂ ame) button.If the appliance will not operate, follow the instructions “TO TURN OFF GAS TO APPLIANCE” (page 28).TO OPEN AND CLOSE SOLENOID VALVE/BURNER ▪ Upon ignition Main Burner and Decorative Burner are ON.▪ Simultaneously press the and (small ﬂ ame) buttons to switch the Decorative Burner OFF.▪ Simultaneously press and (large ﬂ ame) buttons but-tons to switch Decorative Burner ON. NOTE: The latching solenoid valve cannot operate manually. If the receiver battery runs down it will remain in the last operating position. During normal operation the solenoid valve will be reset to the ON position when the GV60 is switched OFF remotely.Figure 25: Switch PanelA) Increase ﬂ ame heightB) ON/OFFC) Decrease ﬂ ame heightSWITCH PANEL To Turn ON Appliance ▪ Press “B” button (see ﬁ gure 25) until a short beep conﬁ rms the start sequence has begun; release button.▪ Continuing beeps conﬁ rm the ignition is in process.▪ Once pilot ignition is conﬁ rmed, there is main gas ﬂ ow.If the pilot does not stay lit after several tries, turn the main valve knob to OFF and follow the instructions “TO TURN OFF GAS TO APPLIANCE” (page 28).STANDBY MODE (PILOT FLAME)▪ Press and hold “C” button to set appliance at pilot ﬂ ame.To Turn OFF Appliance▪ Press “B” button.Flame Height Adjustment▪ Press and hold “A” button to increase ﬂ ame height.▪ Press and hold “C” button to decrease ﬂ ame height or to set appliance at pilot ﬂ ame.▪ For ﬁ ne adjustment tap button “A” or “C” button.If the appliance will not operate, follow the instructions “TO TURN OFF GAS TO APPLIANCE” (page 28).Increase ﬂ ame heightON-OFFDecrease ﬂ ame heightFigure 24: Touch Pad / Wall Switch

OPERATING INSTRUCTIONS FOR OEM USE ONLY© 2013 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.28 / 28MANUAL OPERATION (Only possible, when MANUAL knob is used)Access to the pilot burner is only required for ignition with a match.When turning main valve knob, do not force. Knob has a slip clutch that clicks until the end stops are reached. This allows for manual ﬂ ame height adjustment as well as adjustment to pilot standby position.1. STOP! Read the safety information included before proceeding.2. Turn main valve knob to the OFF, full clockwise position.3. Turn MANUAL knob to the MAN, full clockwise position.4. Place ON/OFF switch (if equipped) in O (OFF position).5. Wait ﬁ ve (5) minutes to clear out any gas. Verify that no gas is in the area around the appliance, including near the ﬂ oor. If you detect gas STOP! Follow “WHAT TO DO IF YOU SMELL GAS” in the safety information on page 2. If no gas is present, proceed to step 6.6. Place ON/OFF switch (if equipped) in “I” (ON position).7. With the MANUAL knob in MAN position a manual pilot valve operator and piezo ignitor (optional) are accessible.8. Fully push down manual pilot valve operator and hold in, to start pilot gas ﬂ ow (see ﬁ gure 25). Ignition with match: Immediately light the pilot with a match, while continuing to hold in the manual pilot valve operator for about one (1) minute after the pilot is lit. Release manual pilot valve operator. If pilot does not stay lit, wait ﬁ ve (5) minutes and repeat. Ignition with piezo ignitor: Change the ignition cable from the receiver to the valve (see ﬁ gure 25). Push in the piezo ignitor to ignite. If pilot does not stay lit, wait ﬁ ve (5) minutes and repeat.If the pilot does not stay lit after several tries, turn the gas control knob (main valve knob) to OFF and proceed to step 12. Figure 25: Combination control, cover8 Wire Receiver jackMicroswitchMANUAL knobin MAN positionMain valve knobin OFF positionManual pilot valve operatorPiezo ignitor(optional)ON/OFF switch(optional) inON PositionConnectionpiezo ignitor tab 2.8 x 0.8 mm9. If applicable, replace pilot access panel before proceeding.10. Turn MANUAL knob to the ON, full counterclockwise position.11. Turn main valve knob to the full ON, full counterclockwise position.12. If the appliance will not operate, follow the instructions “TO TURN OFF GAS TO APPLIANCE” (below).TO TURN OFF GAS TO APPLIANCE1. Place ON/OFF switch (if equipped) in O (OFF position).2. If gas control is accessible turn main valve knob to the OFF full clockwise position.3. Replace appliance access cover (if applicable).AUTOMATIC TURN DOWN3 Hour No Communication Function▪ The valve will turn to pilot ﬂ ame if there is no communication between handset and receiver for a 3 hour period. The ﬁ re will continue to function normally when communication is restored. Receiver Overheating(only if module is connected)▪ Valve turns to pilot ﬂ ame if the temperature in the receiver is higher than 140 °F (60 °C). The main burner turns back ON (manually or in thermostatic mode) only when the temperature is below 140 °F (60 °C).1 Hour Turn Down for Special Receiver (bedroom ﬁ replaces only)▪ The valve will turn to pilot ﬂ ame if there is no change in ﬂ ame height over a 1 hour period.AUTOMATIC SHUT OFFCountdown Timer▪ At end of countdown time period, the ﬁ re turns OFF. The Count-downTimer only works in Manual, Thermostatic, and Random modes. Maximum countdown time is 9 hours.Low Battery Receiver▪ With low battery power in the receiver the system shuts off the ﬁ re completely. This will not happen if the power supply is inter-rupted.Five Day Shut Off (CSA version)▪ The system shuts off the ﬁ re completely if there is no change in ﬂ ame height for 5 days.2nd Thermocouple Shut Off▪ 2nd thermocouple Option: The system shuts OFF the ﬁ re if the main burner does not completely ignite approximately 20 sec-onds after ignition or after pushing button.NOTE: Before the next ignition there is a 2 minute waiting period.Exclusive Distributor North America for Mertik MaxitrolMaxitrol Company, Inc.23555 Telegraph Rd., PO Box 2230, Southfield, MI 48037-2230, USATel: +1 248-356-1400, Fax: +1 248-356-0829www.maxitrol.comMertik Maxitrol GmbH & Co. KGWarnstedter Str. 3, 06502 Thale, GermanyTel: + 49 3947 400-0, Fax: + 49 3947 400-200www.mertikmaxitrol.comRRGV60-II.OI-EN-10.2013-Symax

Navigation menu