Meyer Sound Car Speaker Acheron Designer Screen Channel Loudspeaker Users Manual Operating Instructions
acheron designer screen channel loudspeaker to the manual a3b200c2-f56f-4512-9b18-e953f8e8f4de
2015-02-09
: Meyer-Sound Meyer-Sound-Meyer-Sound-Car-Speaker-Acheron-Designer-Screen-Channel-Loudspeaker-Users-Manual-555519 meyer-sound-meyer-sound-car-speaker-acheron-designer-screen-channel-loudspeaker-users-manual-555519 meyer-sound pdf
Open the PDF directly: View PDF 
.
Page Count: 32
| Download | |
| Open PDF In Browser | View PDF |
OPERATING INSTRUCTIONS
Acheron® Designer Screen Channel Loudspeaker
Keep these important operating instructions.
Check www.meyersound.com for updates.
DECLARATION OF CONFORMITY ACCORDING TO ISO/IEC GUIDE 22 AND EN 45014
Manufacturer’s Name: Meyer Sound Laboratories Inc.
Manufacturer’s Address: 2832 San Pablo Avenue
Berkeley, CA 94702-2204, USA
Declares that the product:
Product Names: Acheron Designer Screen Channel Loudspeaker System
Product Options: All
Conforms to the following Product Specifications:
Safety: EN 60065:2002
Supplementary Information: The product herewith complies with the requirements of the Low Voltage
Directive (LVD) 2006/95/EC and the EMC Directive 2004/108/EC.
Signature:
Ms. Margie Garza
Director of Quality
Meyer Sound Laboratories Inc.
Berkeley, California 94702 USA
Issued October 13, 2011
European Contact:
Your local Meyer Sound dealer or
Meyer Sound Germany, GmbH.
© 2012
Meyer Sound. All rights reserved.
Acheron Designer Operating Instructions, PN 05.211.005.01 A
The contents of this manual are furnished for informational purposes only, are subject to change without notice, and should not be construed as a commitment by Meyer Sound Laboratories Inc. Meyer Sound assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. Except as permitted by applicable copyright law, no part of this publication may be reproduced,
stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording or otherwise, without prior written permission from Meyer Sound.
EXP, Intelligent AC, MAPP Online Pro, RMS, QuietCool, and all alpha-numeric designations for Meyer Sound products and accessories are
trademarks of Meyer Sound. Acheron Designer, Compass, Galileo, Meyer Sound, the Meyer Sound wave logo, and SIM are registered
trademarks of Meyer Sound Laboratories Inc. (Reg. U.S. Pat. & Tm. Off.). All third-party trademarks mentioned herein are the property of
their respective trademark holders.
ii
SYMBOLS USED
These symbols indicate important safety or operating features in this booklet and on the chassis:
!
Dangerous voltages: risk of
electric shock
Important operating instructions
Frame or chassis
Protective earth ground
Pour indiquer les risques
résultant de tensions dangereuses
Pour indequer important
instructions
Masse, châssis
Terre de protection
Warnung vor gefährlicher
elektrischer Spannung
Wichtige Betriebsanweisung oder
Gebrauchsanleitung
Rahmen oder Gehäuse
Masse Schutzleiter
Para indicar voltajes peligrosos
Instrucciones importantes de
funcionamiento y/o manteniento
Armadura o chassis
Tierra proteccionista
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
11. Only use attachments/accessories specified by Meyer
Sound.
12. If applicable, use only with the caster rails or rigging
specified by Meyer Sound, or sold with the loudspeaker.
Handles are for carrying only.
5. Do not use this loudspeaker near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with Meyer Sound’s installation instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus that produce
heat.
9. Do not defeat the safety purpose of the grounding-type
plug. A grounding type plug has two blades and a third
grounding prong. The third prong is provided for your
safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the
point where they exit from the loudspeaker. The AC
mains plug or appliance coupler shall remain readily
accessible for operation.
!
CAUTION: Rigging should only be done by
experienced professionals.
13. Unplug this loudspeaker during lightning storms or when
unused for long periods of time.
14. Disconnect the mains plug before disconnecting the
power cord from the loudspeaker.
15. Refer all servicing to qualified service personnel. Servicing is required when the loudspeaker has been damaged
in any way, such as when the power-supply cord or plug
has been damaged; liquid has been spilled or objects
have fallen into the loudspeaker; rain or moisture has
entered the loudspeaker; the loudspeaker has been
dropped; or when for undetermined reasons the loudspeaker does not operate normally.
CAUTION: To reduce the risk of electric shock,
do not expose this loudspeaker to rain or moisture. Do not install the loudspeaker in wet or humid
locations without using weather protection equipment from Meyer Sound.
!
iii
SAFETY SUMMARY
English
To reduce the risk of electric shock, disconnect the loudspeaker from the AC
mains before installing audio cable.
Reconnect the power cord only after
making all signal connections.
Connect the loudspeaker to a two-pole,
three-wire grounding mains receptacle.
The receptacle must be connected to a
fuse or circuit breaker. Connection to
any other type of receptacle poses a
shock hazard and may violate local
electrical codes.
Do not install the loudspeaker in wet or
humid locations without using weather
protection equipment from Meyer
Sound.
Do not allow water or any foreign object
to get inside the loudspeaker. Do not
put objects containing liquid on or near
the unit.
To reduce the risk of overheating the
loudspeaker, avoid exposing it to direct
sunlight. Do not install the unit near
heat-emitting appliances, such as a
room heater or stove.
Ne pas installer l’haut-parleur dans un
endroit où il y a de l’eau ou une
humidité excessive.
Ne pas laisser de l’eau ou tout objet
pénétrer dans l’haut-parleur. Ne pas
placer de r´cipients contenant un liquide
sur cet appareil, ni à proximité de celuici.
Pour éviter une surchauffe de l’hautparleur, conserver-la à l’abri du soleil.
Ne pas installer à proximité d’appareils
dégageant de la chaleur tels que radiateurs ou appareils de chauffage.
Ce haut-parleur contient des circuits
haute tension présentant un danger. Ne
jamais essayer de le démonter. Il n’y a
aucun composant qui puisse être
réparé par l’utilisateur. Toutes les réparations doivent être effectuées par du
personnel qualifié et agréé par le constructeur.
Um die Gefahr eines elektrischen
Schlages auf ein Minimum zu reduzieren, den Lautsprecher vom Stromnetz
trennen, bevor ggf. ein Audio-Schnittstellensignalkabel angeschlossen wird.
Das Netzkabel erst nach Herstellung
aller Signalverbindungen wieder einstecken.
Der Lautsprecher an eine geerdete
zweipolige Dreiphasen-Netzsteckdose
anschließen. Die Steckdose muß mit
einem geeigneten Abzweigschutz
(Sicherung oder Leistungsschalter) verbunden sein. Der Anschluß der unterbrechungsfreien Stromversorgung an
einen anderen Steckdosentyp kann zu
Stromschlägen führen und gegen die
örtlichen Vorschriften verstoßen.
This loudspeaker contains potentially
hazardous voltages. Do not attempt to
disassemble the unit. The unit contains
no user-serviceable parts. Repairs
should be performed only by factorytrained service personnel.
iv
Pour réduire le risque d’électrocution,
débrancher la prise principale de l’hautparleur, avant d’installer le câble d’interface allant à l’audio. Ne rebrancher le
bloc d’alimentation qu’après avoir
effectué toutes les connections.
Branchez l’haut-parleur dans une prise
de courant à 3 dérivations (deux pôles
et la terre). Cette prise doit être munie
d’une protection adéquate (fusible ou
coupe-circuit). Le branchement dans
tout autre genre de prise pourrait
entraîner un risque d’électrocution et
peut constituer une infraction à la réglementation locale concernant les installations électriques.
Um ein Überhitzen dem Lautsprecher
zu verhindern, das Gerät vor direkter
Sonneneinstrahlung fernhalten und
nicht in der Nähe von wärmeabstrahlenden
Haushaltsgeräten (z.B. Heizgerät oder
Herd) aufstellen.
Im Inneren diesem Lautsprecher herrschen potentiell gefährliche Spannungen. Nicht versuchen, das Gerät zu öffnen. Es enthält keine vom Benutzer
reparierbaren Teile. Reparaturen dürfen
nur von ausgebildetem Kundenienstpersonal durchgeführt werden.
Español
Para reducir el riesgo de descarga eléctrica, desconecte de la red de voltaje el
altoparlante antes de instalar el cable
de señal de audio. Vuelva a conectar la
alimentacion de voltaje una vez efectuadas todas las interconexiones de
señalizacion de audio.
Conecte el altoparlante a un tomacorriente bipolar y trifilar con neutro de
puesta a tierra. El tomacorriente debe
estar conectado a la protección de derivación apropiada (ya sea un fusible o un
disyuntor). La conexión a cualquier otro
tipo de tomacorriente puede constituir
peligro de descarga eléctrica y violar los
códigos eléctricos locales.
No instale el altoparlante en lugares
donde haya agua o humedad excesiva.
No deje que en el altoparlante entre
agua ni ningún objeto extraño. No
ponga objetos con líquidos encima de
la unidad ni cerca de ella.
Para reducir el riesgo de sobrecalentamiento, no exponga la unidad a los
rayos directos del sol ni la instale cerca
de artefactos que emiten calor, como
estufas o cocinas.
Este altoparlante contiene niveles de
voltaje peligrosos en potencia. No
intente desarmar la unidad, pues no
contiene piezas que puedan ser repardas por el usuario. Las reparaciones
deben efectuarse únicamente por parte
del personal de mantenimiento capacitado en la fábrica.
Deutsch
Français
Der Lautsprecher nicht an einem Ort
aufstellen, an dem sie mit Wasser oder
übermäßig hoher Luftfeuchtigkeit in
Berührung kommen könnte.
Darauf achten, daß weder Wasser noch
Fremdkörper in das Innere den
Lautsprecher eindringen. Keine
Objekte, die Flüssigkeit enthalten, auf
oder neben die unterbrechungsfreie
Stromversorgung stellen.
CONTENTS
Chapter 1: Introduction
How to Use This Manual
Acheron Designer Screen Channel Loudspeaker
Chapter 2: Power Requirements
AC Connectors
Wiring for AC Connections
AC Power Distribution
Acheron Designer Voltage Requirements
Powering Up the Acheron Designer
Acheron Designer Current Requirements
Electrical Safety Guidelines
Chapter 3: Amplification and Audio
Audio Connectors
Limiting
On/Status LED
Chapter 4: Rigging
MYA-DES Cradle-Style Yoke
Chapter 5: RMS Remote Monitoring System
RMS Software
RMS Module
Neuron ID for the RMS Module
Resetting the RMS Module
Chapter 6: System Design and Integration Tools
MAPP Online Cinema
SIM 3 Measurement System
Appendix A: Acheron Designer Specifications
7
7
7
9
9
10
10
11
11
11
12
13
13
14
15
17
17
19
19
20
21
21
23
23
24
25
v
CONTENTS
vi
CHAPTER 1: INTRODUCTION
HOW TO USE THIS MANUAL
Make sure to read these operating instructions in their
entirety before configuring a loudspeaker system with
Acheron Designer loudspeakers. In particular, pay close
attention to material related to safety issues.
As you read these operating instructions, you will encounter
the following icons for notes, tips, and cautions:
NOTE: A note identifies an important or useful
piece of information relating to the topic under
discussion.
ACHERON DESIGNER SCREEN CHANNEL
LOUDSPEAKER
At the heart of Meyer Sound's EXP line of cinema products
are the Acheron® high-performance screen channel loudspeakers. The Acheron Designer is the most compact of the
Acheron models, making it an excellent choice for sound
design suites, screening rooms, private theatres, and small
commercial theatres. Optimized for installation behind perforated screens, the Acheron Designer combines the advantages of self-powered technology and innovative horn
design to deliver exceptional, precise coverage for the left,
center, and right screen channels for cinema.
TIP: A tip offers a helpful tip relevant to the topic
at hand.
CAUTION: A caution gives notice that an
action may have serious consequences and
could cause harm to equipment or personnel, and
could cause delays or other problems.
!
Information and specifications are subject to change.
Updates and supplementary information are available at
www.meyersound.com.
Meyer Sound Technical Support is available at:
■
Tel: +1 510 486.1166
■
Tel: +1 510 486.0657 (after hours support)
■
Web: www.meyersound.com/support
■
Email: techsupport@meyersound.com
Acheron Designer (without Optional Grille Frame)
The Acheron Designer uses the same patent-pending horn
technology and high-frequency compression driver as the
other Acheron models, delivering the same 38 Hz to 17 kHz
frequency response. This consistency of fidelity between
Acheron models ensures that soundtracks monitored with
the Acheron Designer translate accurately when played
back in larger rooms with the Acheron 100, Acheron 80,
Acheron Studio, or other calibrated cinema system.
7
CHAPTER 1: INTRODUCTION
Designed specifically for cinema, the Acheron horn features
a very soft roll-off beyond its 80-degree horizontal by 50degree vertical coverage pattern. The extremely wellbehaved horn ensures an accurate acoustic crossover and
consistent vertical coverage pattern through the critical
crossover range between the low- and high-frequency drivers. The optimized crossover point places most of the dialog
in the horn, which is ideal for cinema applications.
The Acheron Designer enclosure is constructed of premium
birch plywood and coated with a low-gloss, black-textured
finish. The cabinet bottom is fitted with two threaded M6
attachment points for the optional MYA-DES cradle-style
yoke, allowing the unit to be suspended from a single hanging point.
Designed and manufactured at Meyer Sound's headquarters in Berkeley, California, the Acheron Designer’s drivers
include one 12-inch low-frequency cone driver, housed in an
optimally tuned, ported enclosure, and one high-frequency
4-inch diaphragm compression driver. The drivers yield
uncompromising quality and are powered by sophisticated
onboard amplification. The self-powered design ensures
consistent results and simplifies installations in both new
and existing rooms.
Acheron Designer with Optional MYA-DES Cradle-Style Yoke
An optional, black cloth grille frame update kit is available
for installations where the Acheron Designer is not placed
behind a screen.
Acheron Designer with Recessed Heat Sink
A proprietary two-channel, Class-D amplifier powers each
driver channel independently. Onboard processing includes
driver protection circuitry, an electronic crossover, and correction filters, ensuring flat frequency and phase responses.
The rear-mounted, recessed heat sink yields efficient convection cooling, and allows the unit to be placed flat against
walls, when necessary.
The optional RMS™ remote monitoring system provides
comprehensive monitoring of system parameters on a
Windows®-based computer.
Acheron Designer with Optional Grille Frame
8
CHAPTER 2: POWER REQUIREMENTS
The Acheron Designer combines advanced loudspeaker
technology with equally advanced power capabilities.
Understanding power distribution, voltage and current
requirements, and electrical safety guidelines is critical to
the safe operation of the Acheron Designer.
AC CONNECTORS
The Acheron Designer user panel includes 3-pole, PowerCon AC connectors.
DO NOT
DISCONNECT
UNDER LOAD
COMMERCIAL
AUDIO SYSTEM
3JKB
AC INPUT
RATING
100-240V~
50-60 Hz
4A MAX
Made in USA with domestic and foreign parts
AC LOOP
OUTPUT
100-240V~
50-60 Hz
8A MAX
Class 1 Wiring
www.meyersound.com
AC Input (Left) and AC Loop Output (Right) Connectors
AC Input Connector (Blue)
The blue AC Input connector supplies power to the
Acheron Designer loudspeaker. The connector is rated at
20 amps and uses a PowerCon3 AC mains locking connector that prevents accidental disconnections. A 10-foot AC
power cable, rated at 15 amps, is included with each
Acheron Designer. If you replace the included AC power
cable, make sure to use a cable with the appropriate power
plug (on the other end) for the region in which you will operate the unit.
The AC Input connector also supplies power to any additional loudspeakers connected to the Acheron Designer’s
gray Loop Output connector. Each Acheron Designer loudspeaker requires approximately 3.24 A rms maximum at
115 V AC and 1.74 A rms maximum at 230 V AC for proper
operation.
AC Loop Output Connector (Gray)
The gray AC Loop Output connector allows multiple
Acheron Designers to be looped and powered from a single
power source. Connect the AC Loop Output of the first
Acheron Designer to the AC Input of the second unit, and so
forth. The AC Loop Output uses a PowerCon3 AC mains locking connector that prevents accidental disconnections.
The maximum number of loudspeakers that can be looped
from the Loop Output connector is determined by the voltage of the power source, the current draw of the looped
loudspeakers, the circuit breaker rating, and the rating of the
AC power cable connected to Acheron Designer.
Table 1: Maximum Number of Acheron Designers that Can Be
Looped with AC Power
Circuit Breaker/
Connector Rating
115 V AC
230 V AC
100 V AC
15 amps
3 looped
(4 total)
7 looped
(8 total)
2 looped
(3 total)
20 amps
5 looped
(6 total)
10 looped
(11 total)
3 looped
(4 total)
NOTE: The Acheron Designer current draw is
dynamic and fluctuates as operating levels
change. The numbers in Table 1 assume that operating levels are normal and not such that the loudspeakers are constantly limiting.
Each Acheron Designer ships with one AC looping connector for making AC looping cables. Assembled AC looping
cables are available from Meyer Sound.
CAUTION: Do not exceed the current capability of the 20-amp Input connector for the
Acheron Designer. When looping loudspeakers, consider the total current draw for all loudspeakers on
the circuit, including the first loudspeaker.
!
CAUTION: When using the included AC power
cable, do not loop more than three additional
Acheron Designers from the AC Loop Output connector at 115 V (four total for the circuit), and not
more than seven at 230 V (eight total for the circuit).
!
9
CHAPTER 2: POWER REQUIREMENTS
WIRING FOR AC CONNECTIONS
AC POWER DISTRIBUTION
The Acheron Designer requires a grounded outlet. To operate safely and effectively, it is extremely important that the
entire system be properly grounded.
All components in an audio system (self-powered loudspeakers, mixing consoles, and processors) must be properly connected to an AC power distribution system to ensure
that AC line polarity is preserved, and that all grounding
points are connected to a single node or common point
using the same cable gauge as the neutral and line cables.
Blue = neutral
Brown = hot
NOTE: Improper grounding of connections
between loudspeakers and the rest of the
audio system may produce noise or hum, or cause
serious damage to the input and output stages of the
system’s electronic components.
Yellow/green =
earth ground
(chassis)
CAUTION: Before applying AC power to any
Meyer Sound self-powered loudspeaker, make
sure that the voltage potential difference between the
neutral and earth-ground lines is less than 5 V AC
when using single-phase AC wiring.
!
AC Cable Wiring Scheme
When wiring international or special-purpose AC power
cables and connectors, use the following wiring scheme:
■
Connect the blue wire to the black terminal, or the terminal marked with an N.
■
Connect the brown wire to the red terminal, or the terminal marked with an L.
■
Connect the yellow and green wire to the green (or green
and yellow) terminal, or the terminal marked with an E.
CAUTION: When creating AC power cables
and distribution systems, it is important to preserve AC line polarity and connect the earth ground
on both ends of the cable. The Acheron Designer
requires a grounded connection. Always use a
grounded outlet and plug. It is extremely important
that the system be properly grounded to operate
safely and properly. Do not ground-lift the AC cable.
Figure 1 illustrates a basic three-phase AC distribution system with the loudspeaker load distributed across the three
phases. All loudspeakers are connected to common neutral
and earth-ground lines.
!
Line 1
Line 2
Line 3
Neutral
Earth Ground
Figure 1: AC Power Distribution System
10
ACHERON DESIGNER OPERATING INSTRUCTIONS
ACHERON DESIGNER VOLTAGE
REQUIREMENTS
The Acheron Designer operates safely and continuously
when the AC voltage stays within 100–264 V AC at 50 or
60 Hz. The loudspeaker can withstand continuous voltages
up to 275 volts and allows any combination of voltage to
GND (neutral-line-ground or line-line-ground).
If the voltage drops below 90 V (brownout), the unit uses
stored power to continue operating temporarily; the loudspeaker shuts down if the voltage does not rise above the
low boundary before the stored power is used.
If the voltage rises above 275 V, the power supply immediately shuts off to prevent damage to the unit.
If the Acheron Designer shuts down due to either low or high
voltage, its power supply automatically powers up again
after three seconds, so long as the voltage has returned to
its normal operating window. If the Acheron Designer does
not power up after 10 seconds, remove AC power immediately and contact Meyer Sound Technical Support.
CAUTION: The power source for the
! Acheron Designer should always operate
within the required voltage range, at least a few volts
from the upper and lower ranges. This ensures that
AC voltage variations from the service entry — or
peak voltage drops due to cable runs — will not
cause the loudspeaker’s amplifier to cycle on and off
or cause damage to the power supply.
NOTE: When voltage fluctuates within the
Acheron Designer’s operating range, automatic
tap selection stabilizes the operating voltage. This
tap selection is instantaneous with no audible artifacts.
TIP: Since the Acheron Designer does not
require a dedicated neutral line, and it can tolerate elevated voltages from the ground line, it can be
connected to line-line terminals in 120 V, 3-phase
Wye systems. This results in 208 V AC between lines
(nominal) and therefore draws less current than when
using 120 V AC (line-neutral). Make sure that the voltage remains within the Acheron Designer’s recommended operating window (100-264 V AC). The
ground line must always be used for safety reasons
and the line-to-ground voltage should never exceed
264 V AC (typically 120 V AC from line-to-ground).
POWERING UP THE ACHERON DESIGNER
When AC power is applied to the Acheron Designer, its
Intelligent AC™ power supply automatically selects the correct operating voltage, allowing it to be used internationally
without manually setting voltage switches. In addition,
Intelligent AC provides soft-start power up, eliminating high
inrush currents; suppresses high-voltage transients up to
several kilovolts; filters common mode and differential mode
radio frequencies (EMI); and sustains operation temporarily
during low-voltage periods.
When powering up the Acheron Designer, the following
startup events take place over several seconds.
1. Audio output is muted.
2. Voltage is detected and the power supply mode is automatically adjusted as necessary. The power supply
ramps up.
3. During the power up sequence, the three-color On/Status LED flashes all three colors.
4. After the power up sequence and system check have
completed, the ON/Status LED turns solid green, indicating the loudspeaker is ready to reproduce audio.
CAUTION: If the On/Status LED does not turn
green, or the Acheron Designer does not output audio after ten seconds, remove AC power immediately and verify that the voltage is within the
required range. If the problem persists, contact
Meyer Sound Technical Support.
!
ACHERON DESIGNER CURRENT
REQUIREMENTS
The Acheron Designer current draw is dynamic and fluctuates as operating levels change. Since different cables and
circuit breakers heat up at varying rates, it is important to
understand the following types of current ratings and how
they affect circuit breaker and cable specifications.
■
Idle Current — The maximum rms current during idle
periods.
■
Maximum Long-Term Continuous Current — The
maximum rms current during a period of at least 10 seconds. The Maximum Long-Term Continuous Current is
used to calculate temperature increases for cables, to
ensure that cable sizes and gauges conform to electrical
code standards. The current rating is also used as a rating for slow-reacting thermal breakers.
11
CHAPTER 2: POWER REQUIREMENTS
■
Burst Current — The maximum rms current during a
period of around one second. The Burst Current is used
as a rating for magnetic breakers. It is also used for calculating the peak voltage drop in long AC cable runs
according to the following formula:
ELECTRICAL SAFETY GUIDELINES
Pay close attention to these important electrical and safety
guidelines.
■
The Acheron Designer requires a grounded outlet.
Always use a grounded outlet and plug.
■
Do not use a ground-lifting adapter or cut the AC cable
ground pin.
V pk (drop) = I pk x R (cable total)
The Burst Current can also be used to calculate the AC
looping capability of Acheron Designer.
■
Ultimate Short-Term Peak Current — A rating for fastreacting magnetic breakers.
■
Inrush Current — The spike of initial current encountered when powering on.
You can use Table 2 as a guideline for selecting cable
gauges and circuit breaker ratings for the system’s operating voltage.
Table 2: Acheron Designer Current Draw
Current Draw
115 V AC
230 V AC
100 V AC
Idle Current
0.23 A rms
0.19 A rms
0.24 A rms
Maximum Long-Term
Continuous Current
1.58 A rms
0.83 A rms
1.78 A rms
Burst Current
3.1 A rms
1.4 A rms
3.6 A rms
12.0 A peak
8.0 A peak
12.4 A peak
25 A peak
54 A peak
20 A peak
Ultimate Short-Term
Peak Current
Inrush Current
Earth ground
Chassis ground
The minimum electrical service amperage required by an
Acheron Designer loudspeaker system is the sum of the
Maximum Long-Term Continuous Current for each loudspeaker. An additional 30 percent above the minimum
amperage is recommended to prevent peak voltage drops at
the service entry.
NOTE: For best performance, the AC cable
voltage drop should not exceed 10 V, or
10 percent at 115 V and 5 percent at 230 V. Make
sure that even with AC voltage drops that the AC
voltage always remains within the operating windows.
12
■
Do not exceed the current capability of the 20-amp AC
Input connector for the loudspeaker. When looping loudspeakers, consider the total current draw for all loudspeakers on the circuit, including the first loudspeaker.
■
Make sure the AC power cable for the loudspeaker has
the appropriate power plug (on the other end) for the
area in which you will operate the loudspeaker. In addition, the AC power cable must be rated for the total current draw of all loudspeakers looped from the power
source.
■
Do not operate the unit if its power cable is frayed or broken.
■
Keep all liquids away from the Acheron Designer to avoid
hazards from electrical shock.
CHAPTER 3: AMPLIFICATION AND AUDIO
The Acheron Designer’s low- and high-frequency drivers are
powered by an extremely efficient onboard two-channel,
Class-D amplifier that uses minimal AC power when idle.
Internal signal processing includes a complex crossover, frequency and phase correction, and limiters that prevent
driver overexcursion and regulate voice coil temperatures,
ensuring maximum driver lifespan.
Input
AUDIO CONNECTORS
The Acheron Designer includes female XLR Input and male
XLR Loop output connectors.
Input
Loop
Limit
Looping Audio Input
10k Balanced
2
3
1
Loop
Looping Audio Input
10k Balanced
Limit
On / Status
2
AVIS
RISQUE DE CHOC
ELECTRIQUE
NE PAS OUVRIR
CAUTION
3
1
On / Status
Earth/Chassis
GND Circuit
1k
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
Earth/Chassis
Remote Mute
RMS Network
Disable Enable
RMS 4.0
Firmware
Wink
Activity
DO NOT
DISCONNECT
UNDER LOAD
COMMERCIAL
AUDIO SYSTEM
3JKB
AC INPUT
RATING
100-240V~
50-60 Hz
4A MAX
Made in USA with domestic and foreign parts
Acheron Designer Audio Connectors, Input and Loop Output
Input Connector
NID: 001848623900
Identify
GND Circuit
1k
AC LOOP
OUTPUT
100-240V~
50-60 Hz
8A MAX
Class 1 Wiring
The female XLR Input connector accepts a balanced audio
signal with an input impedance of 10 kOhm. The connector
uses the following wiring:
■
Pin 1 — 1 kOhm to chassis and earth ground (ESD
clamped)
■
Pin 2 — Signal (+)
■
Pin 3 — Signal (–)
■
Case — Earth (AC) ground and chassis
www.meyersound.com
Acheron Designer Rear Panel with Optional RMS Module
The Acheron Designer rear panel includes a slot for the
optional RMS module, used for connecting to the RMS
remote monitoring system (see Chapter 5, “RMS Remote
Monitoring System”).
Pins 2 and 3 carry the input as a differential signal. Pin 1 is
connected to earth through a 1 kOhm, 1000 pF, 15 V
clamped network. This circuitry provides virtual ground lift
for audio frequencies while allowing unwanted signals to
bleed to ground. Make sure to use standard, balanced XLR
audio cables with all three pins connected on both ends.
Telescopic grounding is not recommended, and shorting an
input connector pin to the case may cause a ground loop,
resulting in hum.
TIP: If unwanted noise or hiss is produced by
the loudspeaker, disconnect its input cable. If
the noise stops, there is most likely nothing wrong
with the loudspeaker. To locate the source of the
noise, check the audio cable, source audio, and AC
power.
13
CHAPTER 3: AMPLIFICATION AND AUDIO
Loop Output Connector
LIMITING
The male XLR Loop output connector allows multiple
Acheron Designers to be looped from a single audio source.
For applications that require multiple Acheron Designers,
connect the Loop output of the first unit to the Input of the
second, and so forth.
When source levels for the Acheron Designer exceed optimum input levels for its drivers, limiting is engaged and is
indicated by the two Limit LEDs on the rear panel. The bottom LED indicates limiting for the low-frequency channel.
The top LED indicates limiting for the high-frequency channel. When engaged, limiting not only protects the drivers,
but also prevents signal peaks from causing excessive distortion in the amplifier’s channels, thereby preserving headroom and maintaining smooth frequency responses at high
levels. When source levels return to normal, below the limiter’s threshold, limiting ceases.
NOTE: The order in which loudspeakers are
connected when looping audio signals is unimportant. The Loop connector is wired in parallel to the
Input connector and transmits the unbuffered source
signal even when the Acheron Designer is powered
off.
High-frequency limiter (top LED)
Low-frequency limiter (bottom LED)
To avoid distortion when looping multiple Acheron Designers,
make sure the source device can drive the total load impedance of the looped loudspeakers. In addition, the source
device must be capable of delivering approximately 20 dBV
(10 V rms into 600 ohms) to yield the maximum peak SPL
over the entire operating bandwidth of the loudspeakers.
Most professional audio equipment can transmit these
source levels.
To calculate the load impedance for the looped loudspeakers, divide 10 kOhms (the input impedance for a single
Acheron Designer) by the number of looped loudspeakers.
For example, the load impedance for 10 Acheron Designer
loudspeakers is 1000 ohms (10 kOhms / 10). To drive this
number of looped loudspeakers, the source device should
have an output impedance of 100 ohms or less. This same
rule applies when looping Acheron Designer loudspeakers
with other self-powered Meyer Sound loudspeakers and
subwoofers.
NOTE: Most source devices are capable of
driving loads no smaller than 10 times their
output impedance.
CAUTION: Make sure that all cabling for
looped loudspeakers is wired correctly (Pin 1
to Pin 1, Pin 2 to Pin 2, and so forth) to prevent the
polarity from being reversed. If one or more loudspeakers in a system have reversed polarity, frequency response and coverage will be significantly
degraded.
!
14
Input
Limit
AVIS
RISQUE DE CHOC
ELECTRIQUE
NE PAS OUVRIR
CAUTION
On / Status
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
Limit LEDs
The Acheron Designer performs within its acoustical specifications at normal temperatures when the Limit LEDs are
unlit, or if the LEDs are lit for two seconds or less and then
turn off for at least one second. If an LED remains lit for longer than three seconds, the loudspeaker enters hard limiting
where:
■
Increases to the input level have no effect.
■
Distortion increases due to clipping and nonlinear driver
operation.
■
The drivers are subjected to excessive heat and excursion, which will compromise their life span and may
eventually lead to damage over time.
NOTE: The Acheron Designer uses digital limiters that add no noise and have no effect on the
signal when the limiters are not engaged and the
Limit LEDs are not lit.
ACHERON DESIGNER OPERATING INSTRUCTIONS
ON/STATUS LED
Heat Sink Ventilation Requirements
During normal operation, the Acheron Designer’s On/Status
LED is green. If the loudspeaker’s internal temperature
reaches 75° C (167° F), the LED turns solid yellow and the
loudspeaker’s gain is reduced by 3 dB. Though the
Acheron Designer will continue to operate normally with the
lower gain, when the On/Status LED is yellow, this is an indication that the loudspeaker is reaching its maximum heat
dissipation and a reduction in SPL is recommended. When
the loudspeaker’s internal temperature cools to 60° C
(140° F), the amplifier returns to normal operation.
When installing the Acheron Designer flush against walls, or
when mounting them in soffits or baffle walls, make sure to
allow plenty of ventilation above the loudspeaker.
■
When installing the Acheron Designer in a soffit with the
loudspeaker flush against the back of the soffit (see
Figure 2), allow at least 6 inches above the loudspeaker
for ventilation.
CAUTION: If the loudspeaker’s internal temperature reaches 125° C (257° F), gain is
reduced by 6 dB to avoid damage to the loudspeaker.
!
TIP: When the Acheron Designer is connected
to an RMS network, the RMS software provides
additional feedback on the loudspeaker’s operating
temperature. For more information, see Chapter 6,
“RMS Remote Monitoring System.”
6.00
[152 mm]
Amplifier Cooling System
The Acheron Designer’s amplifier relies solely on natural
convection for cooling from air flowing over its heat sink.
The rear-mounted, recessed heat sink yields efficient cooling and allows the unit to be placed flat against walls, when
necessary. The amplifier and heat sink keep temperatures
low, even when the unit is used at high ambient temperatures, and when driven continuously at high output levels.
CAUTION: The Acheron Designer’s heat sink
can reach temperatures of up to 85° C (185° F)
during extreme operation. Use extreme caution when
approaching the rear of the loudspeaker.
!
Figure 2: Acheron Designer Mounted in Soffit, Flush Against Back
of Soffit with 6” of Ventilation Above Loudspeaker
15
CHAPTER 3: AMPLIFICATION AND AUDIO
■
When installing the Acheron Designer in a soffit with the
loudspeaker 1 inch from the back of the soffit (see
Figure 3), allow at least 3 inches above the loudspeaker
for ventilation.
■
When installing the Acheron Designer in a baffle wall with
no opening in the front of the wall for ventilation (see
Figure 4), allow for plenty of ventilation above the loudspeaker within the baffle wall.
3.00
[76 mm]
1.00
[25 mm]
Figure 3: Acheron Designer Mounted in Soffit, 1” Behind and 3”
Above Loudspeaker for Ventilation
16
Figure 4: Acheron Designer Mounted in Baffle Wall with Open
Ventilation Above Loudspeaker
CHAPTER 4: RIGGING
Important Safety Considerations!
When installing Meyer Sound loudspeakers and subwoofers, the following precautions should always be observed:
■
All Meyer Sound products must be used in accordance
with local, state, federal, and industry regulations. It is
the owner’s and user’s responsibility to evaluate the reliability of any mounting and rigging method for their
application. Mounting and rigging should only be carried
out by experienced professionals.
■
Use mounting and rigging hardware that has been rated
to meet or exceed the weight being hung.
■
Make sure to attach mounting hardware to the building's
structural components (studs or joists), and not just to
the wall surface. Verify that the building's structure and
the anchors used for the installation will safely support
the total weight of the mounted loudspeakers.
■
Use mounting hardware appropriate for the surface
where the loudspeaker will be installed.
■
Make sure bolts and eyebolts are tightened securely.
Meyer Sound recommends using Loctite® on eyebolt
threads and safety cables.
■
Inspect mounting and rigging hardware regularly. Immediately replace any worn or damaged components.
The yoke’s cradle can be pivoted to install the loudspeaker
with downtilt or uptilt. A “C” or “G” hanging clamp and steel
safety cable (not included) are required to suspend the yoke.
MYA-DES CRADLE-STYLE YOKE
The Acheron Designer includes M6 threaded attachment
points on the cabinet bottom for the optional MYA-DES cradle-style yoke, allowing the unit to be suspended from a single hanging point.
MYA-DES Cradle-Style Yoke, Bottom View
!
CAUTION: The MYA-DES mounting yoke is
rated for a maximum downtilt of 45 degrees.
NOTE: The top bar of the MYA-DES yoke
accommodates hanging clamps with standard
1/2- inch or 12 mm bolts.
M6 threaded
attachment
points
NOTE: For Acheron Designer dimensions and
weight with the MYA-DES yoke, refer to
Appendix A, “Acheron Designer Specifications.”
Acheron Designer Cabinet Bottom, M6 Threaded Attachment Points
17
CHAPTER 4: RIGGING
18
CHAPTER 5: RMS REMOTE MONITORING SYSTEM
The Acheron Designer is optionally available with the RMS
remote monitoring system module, allowing it to be connected to an RMS network. RMS allows real-time monitoring of multiple Meyer Sound self-powered loudspeakers
from a Windows-based computer. The RMS host computer
communicates with Meyer Sound loudspeakers (equipped
with RMS modules) via a simple twisted pair network, or an
Ethernet network using an FT-10 to Ethernet adapter.
NOTE: For the latest RMS system requirements, visit www.meyersound.com.
RMS SOFTWARE
The optional RMS software provides extensive system status and performance data for each loudspeaker, including
amplifier voltage, limiting activity, power output, driver status, as well as mute and solo capability. Loudspeakers are
added to the RMS network and assigned a node name during a one-time commissioning procedure where the loudspeaker is identified by either entering its unique Neuron ID,
or by pressing its Identify button.
NOTE: The RMS software allows you to disable Mute and Solo functions to eliminate any
possibility of accidentally muting loudspeakers. Mute
and solo capability can also be disabled by removing
the Mute Jumper from RMS modules. For more information, refer to the RMS User Guide.
NOTE: RMS does not control AC power.
RMS Add Loudspeaker Dialog Box
Once loudspeakers are identified on the RMS network, they
appear in the RMS software as icons and views; they are
also automatically added to the RMS database on the host
computer.
Acheron Designer RMS Icons
19
CHAPTER 5: RMS REMOTE MONITORING SYSTEM
RMS software displays all loudspeakers on the network in a
panel with icons, Meter views, and Text views that can be
customized to suit your needs. Loudspeaker data is
updated 2–5 times per second. Individual loudspeakers can
be physically identified with the Wink option in RMS, which
lights the Wink LED on the RMS module for that particular
loudspeaker. Conversely, a loudspeaker can be identified in
the RMS software by pressing the Identify button on the
loudspeaker’s RMS module.
RMS MODULE
The Acheron Designer RMS module includes an Identify
button, Wink/Activity LED, Remote Mute switch, and two
Network connectors.
Figure 5: Acheron Designer RMS Module
NOTE: The buttons and LED on the
Acheron Designer RMS module are used
exclusively by RMS and have no effect on the acoustical or electrical activity of the loudspeaker.
Identify Button
The Identify button serves the following functions:
■
If the loudspeaker has not yet been commissioned
(Wink/Activity LED not lit), press the Identify button to
identify the loudspeaker on the RMS network and commission it.
■
To decommission the loudspeaker, press and hold the
Identify button during startup (see “Resetting the RMS
Module” on page 21).
■
To wink a commissioned loudspeaker, press the Identify
button. The Wink LED on the loudspeaker icon in the
RMS software lights up and the Wink/Activity LED on the
loudspeaker’s RMS user panel turns solid green. Press
the Identify button again to unwink the loudspeaker.
RMS Panel with Icons
Loudspeaker icons and views can be arranged to represent
how loudspeakers have been deployed in the system. Multiple panels can be saved and recalled for specific performances and venues.
NOTE: When the Acheron Designer heat sink
reaches 85° C (185° F), the On/Status LED
turns red, while its loudspeaker icon in the RMS software turns yellow — indicating the loudspeaker is
running hot, but still within safe operating limits.
Make sure that the loudspeaker is properly ventilated.
20
TIP: The Wink function is useful for identifying
the physical loudspeaker corresponding to a
loudspeaker icon in the RMS software.
ACHERON DESIGNER OPERATING INSTRUCTIONS
Wink/Activity LED (Green)
RMS Network Connectors
The green Wink/Activity LED indicates the status of the
loudspeaker:
The two Weidmuller connectors transfer data to and from
the RMS network. Two connectors are provided to allow for
easy connection of multiple (daisy-chained) loudspeakers
on the network. Included with each RMS-equipped loudspeaker are RMS cable connectors and mounting blocks for
constructing RMS cables. The RMS blocks allow the cables
to be securely attached to the RMS module with screws.
■
During startup, the LED blinks 10 times.
■
If the loudspeaker has not yet been commissioned, the
LED is not lit after startup.
■
If the loudspeaker has been successfully commissioned,
the LED flashes continuously and flashes more rapidly
with increased data activity.
■
When the loudspeaker is winked, either by clicking the
Wink button in the RMS software or by pressing the
Identify button on the RMS user panel, the LED is solid
green.
TIP: The Wink function is useful for identifying
the physical loudspeaker corresponding to a
loudspeaker icon in the RMS software.
Remote Mute Switch
The recessed Remote Mute switch on the Acheron Designer
RMS module determines whether the RMS software can
control muting and soloing of the loudspeaker. The
Acheron Designer ships from the factory with the switch
enabled.
NEURON ID FOR THE RMS MODULE
Each Acheron Designer RMS module has a unique 12-character Neuron ID (NID) that identifies the loudspeaker on the
network. When commissioning the loudspeaker, the NID
must either by entered manually or retrieved from the loudspeaker by pressing its Identify button. The NID for the RMS
module is located on the user panel above the orange RMS
Network connectors (see Figure 5 on page 20).
RESETTING THE RMS MODULE
You can use the Identify button to reset the Acheron Designer
RMS module when powering up the loudspeaker. This will
cause the module to be decommissioned from the network.
To reset the Acheron Designer RMS module:
1. Disconnect the loudspeaker’s power cord.
2. Press and hold the Identify button.
3. While continuing to hold down the Identify button, reconnect the power cord.
Remote Mute Switch
■
Disable: When the Remote Mute switch is set to Disable
(to the left), the loudspeaker cannot be muted and
soloed from the RMS software.
■
Enable: When the Remote Mute switch is set to Enable
(to the right), the loudspeaker can be muted and soloed
from the RMS software.
4. After the Wink/Activity LED blinks on and off, release the
Identify button. The RMS module is reset and the loudspeaker is decommissioned.
NOTE: The RMS software also allows you to
disable Mute and Solo functions to eliminate
any possibility of accidentally muting loudspeakers.
For more information, refer to the RMS User Guide.
21
CHAPTER 5: RMS REMOTE MONITORING SYSTEM
22
CHAPTER 6: SYSTEM DESIGN AND INTEGRATION TOOLS
Meyer Sound offers two comprehensive tools to assist with
the acoustical and functional requirements of system design
and optimization. This chapter introduces MAPP Online
Cinema, Meyer Sound’s patented online acoustical prediction tool, and SIM 3, a comprehensive system for measurement and analysis.
MAPP ONLINE CINEMA
MAPP Online Cinema is a powerful, cross-platform, Javabased application for accurately predicting the coverage
pattern, frequency response, impulse response, and maximum SPL output of Meyer Sound cinema loudspeakers.
Residing on your local computer, the MAPP Online Cinema
client lets you configure Meyer Sound loudspeaker systems
and define the environment in which they will operate,
including air temperature, pressure, humidity, and even the
location and composition of walls. CAD (DXF) files containing detailed venue information can also be imported.
The key to the accuracy of MAPP Online Cinema’s predictions is its exhaustive database of Meyer Sound loudspeaker measurements. Performance predictions for each
loudspeaker are based on 360 1/48th-octave-band measurements taken with a SIM audio analyzer in the Meyer
Sound anechoic chamber. The extraordinary consistency
between Meyer Sound loudspeakers guarantees that predictions from MAPP Online Cinema will closely match their
actual performance.
MAPP Online Cinema predictions are requested by the client
software and sent via the Internet to the high-speed Meyer
Sound servers where high-resolution (magnitude and phase)
polar data is processed with sophisticated acoustical prediction algorithms. The resulting predictions are then
returned to and displayed on the local computer running the
MAPP Online Cinema client software.
TIP: Meyer Sound offers seminars and webinars
on using MAPP Online Cinema. For more information, visit www.meyersound.com.
MAPP Online Cinema Applications
With MAPP Online Cinema, you can:
■
Simulate different loudspeaker configurations to refine
system design and zero-in on the best coverage for
intended audience areas
■
Simulate different screen types to evaluate their transparence and reflectivity
■
Monitor loudspeaker interactions to locate destructive
interferences so that loudspeakers can be re-aimed and
repositioned as necessary
■
Place microphones anywhere in the sound field and predict their frequency response, impulse response, and
sound pressure
■
Determine delay settings for surround loudspeakers
■
Try out virtual Galileo equalization to determine optimum
real-world settings for the best system response
■
Generate and export system images for client presentations
MAPP Online Cinema
Sound system designers can use MAPP Online Cinema to
accurately predict the appropriate loudspeaker deployment
for each job, complete with coverage data, system delay
and equalization settings, and detailed design illustrations.
MAPP Online Cinema’s accurate, high-resolution predictions ensure that systems will perform as expected, thereby
eliminating unexpected coverage problems and minimizing
on-site adjustments.
23
CHAPTER 6: SYSTEM DESIGN AND INTEGRATION TOOLS
Using MAPP Online Cinema
Source Independent Measurement Technique
MAPP Online Cinema is compatible with the following operating systems:
The SIM 3 audio analyzer implements Meyer Sound’s source
independent measurement technique, a dual-channel
method that accommodates statistically unpredictable excitation signals. Any excitation signal within a desired frequency range can be used to obtain highly accurate
measurements for acoustical or electronic systems. For
example, concert halls and loudspeaker systems can be
captured during a performance and used as a SIM 3 test
signal, so you can:
■
Windows
■
Linux®
■
Unix®
■
Mac OS®
For information on which operating system versions are
supported, visit www.meyersound.com.
Downloading and Installing MAPP Online Cinema
To use MAPP Online Cinema, you must register online at
www.meyersound.com. After entering your registration
information, an email will be sent to you with your user
name, password, and the MAPP Online Cinema download
location. On-screen instructions will guide you through the
download and installation process.
The MAPP Online Cinema client software is regularly
upgraded to add support for the latest Meyer Sound loudspeakers, as well as to add feature enhancements. Most
upgrades are downloaded automatically when logging on to
a MAPP Online Cinema session. The MAPP Online Cinema
database includes all Meyer Sound EXP screen channel
loudspeakers, surround loudspeakers, subwoofers, and
processors.
■
View measurement data as amplitude versus time
(impulse response) or amplitude and phase versus frequency (frequency response)
■
Utilize a single-channel spectrum mode
■
View frequency domain data within a logarithmic frequency axis
■
Determine and internally compensate for propagation
delays using the SIM 3 Delay Finder
SIM 3 Applications
The SIM 3’s primary applications are testing and aligning
loudspeaker systems, which entails:
■
Measuring propagation delays between subsystems to
determine appropriate polarities and delay times
■
Measuring variations in frequency response caused by
the acoustical environment and the placement and interaction of loudspeakers to determine corrective equalization
■
Optimizing subwoofer integrations
■
Optimizing loudspeaker arrays
SIM 3 MEASUREMENT SYSTEM
The SIM 3 audio analyzer is a high-resolution audio measurement system comprised of software, hardware, microphones, and accessory cables. The SIM 3 is optimized for
measuring audio frequencies with resolutions up 1/48th of
an octave, allowing you to apply precise corrections to balance system response using frequency and phase domain
information.
24
The SIM 3 is also versatile and accurate enough for the following applications:
■
Microphone calibration and equalization
■
Transducer evaluation and correction
■
Echo detection and analysis
■
Vibration analysis
■
Architectural acoustics
■
Underwater acoustics
APPENDIX A: ACHERON DESIGNER SPECIFICATIONS
ACOUSTICAL
Operating Frequency Range
37 Hz – 18 kHz
Note: Recommended maximum operating frequency range. Response depends on loading
conditions and room acoustics.
Frequency Response
38 Hz – 17 kHz ±4 dB
Note: Measured free field with 1/3 octave frequency resolution at 4 meters.
Phase Response
230 Hz to 17 kHz ±30°
Maximum Peak SPL
130 dB
Note: Measured free field with music referred to 1 meter.
Dynamic Range
>110 dB
Coverage
80° horizontal by 50° vertical
Crossover
680 Hz
Note: At this frequency, both transducers produce equal sound pressure levels.
TRANSDUCERS
Low Frequency
One 12” cone driver
Nominal impedance: 2
Voice coil size: 4”
High Frequency
One 4” compression driver
Nominal impedance: 8
Voice coil size: 4”
Diaphragm size: 4”
Exit size: 1.5”
AUDIO INPUT
Type
Differential, electronically balanced
Maximum Common Mode Range
±5 V DC, clamped to earth for voltage transient protection
Connectors
Female XLR input with male XLR loop output
Input Impedance
10 k differential between pins 2 and 3
Wiring
Pin 1: Chassis/earth through 1 k, 1000 pF, 15 V clamp network to provide virtual ground lift at
audio frequencies
Pin 2: Signal +
Pin 3: Signal –
Case: Earth ground and chassis
DC Blocking
Differential DC blocking up to the maximum common mode voltage
CMRR
>50 dB, typically 80 dB (50 Hz – 500 Hz)
RF Filter
Common mode: 425 kHz
Differential mode: 142 kHz
TIM Filter
<80 kHz, integral to signal processing
Nominal Input Sensitivity
10 dBV (3.2 V rms, 4.5 V peak) continuous is typically the onset of limiting for noise and music
Input Level
Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
AMPLIFIER
Type
Two-channel, Class-D
25
APPENDIX A: ACHERON DESIGNER SPECIFICATIONS
Output Power
700 W total (550 W low channel, 250 W high channel)
Note: Amplifier wattage rating based on the maximum unclipped burst sine-wave RMS voltage the amplifier will produce into the nominal load impedance: low-frequency channel, 33 V
rms into 2 ; high-frequency channel, 33 V rms into 8 .
Total Output
1400 W peak
Note: Peak power output based on the maximum unclipped peak voltage the amplifier will
produce into the nominal load impedance: low-frequency channel, 46 V peak into 2 ; highfrequency channel, 46 V peak into 8 .
THD, IM TIM
<.02%
Load Capacity
2 low channel, 8 high channel
Cooling
Convection, with recessed heat sink
AC POWER
Connectors
PowerCon with loop output
Voltage Selection
Automatic, continuous range from 90–265 V AC
Safety Agency Rated Operating Voltage
100–240 V AC, 50/60 Hz
Turn On/Turn Off Points
90 V AC on, no turn-off, only fuse-protect above 265 V AC
Current Draw
Idle Current
0.23 A rms (115 V AC); 0.19 A rms (230 V AC); 0.24 A rms (100 V AC)
Maximum Long-Term Continuous
Current
1.58 A rms (115 V AC); 0.83 A rms (230 V AC); 1.78 A rms (100 V AC)
Burst Current
3.1 A peak (115 V AC); 1.4 A peak (230 V AC); 3.6 A peak (100 V AC)
Note: AC power cabling must be of sufficient gauge so that under burst current rms conditions, cable transmission losses do not drop below the loudspeaker’s specified operating voltage range.
Ultimate Short-Term Peak Current
12.0 A peak (115 V AC); 8.0 A peak (230 V AC); 12.4 A peak (100 V AC)
Inrush Current
25 A peak (115 V AC); 54 A peak (230 V AC); 20 A peak (100 V AC)
PHYSICAL
Enclosure
Premium birch plywood
Finish
Low gloss, black textured
Protective Grille (Optional)
Attachment points on cabinet front corners for optional grille frame with black cloth
Note: Weight for grille frame is 2.0 lbs ((0.9 kg).
Rigging (Optional)
Two threaded M6 attachment points on cabinet bottom for optional MYA-DES cradle-style
yoke
Note: Weight for MYA-DES is 28.5 lbs (12.9 kg).
Dimensions
19.00" w x 25.38" h x 14.58" d (483 mm x 645 mm x 370 mm) without optional grille frame
Weight
Weight 76.0 lbs (34.5 kg) without optional grille frame
ENVIRONMENTAL
Operating Temperature
0° C to +45° C
Non Operating Temperature
<–40° C or >+75° C
Humidity
to 95% at 35° C
Operating Altitude
to 4600 m (15,000 ft)
Non Operating Altitude
to 95% at 35° C
Shock
30 g 11 msec half-sine on each of 6 sides
Vibration
10 Hz – 55 Hz (0.010 m peak-to-peak excursion)
26
ACHERON DESIGNER OPERATING INSTRUCTIONS
ACHERON DESIGNER COMPLIANCE
ACHERON DESIGNER DIMENSIONS
14.96
[380 mm]
6.00
[152 mm]
6.96
[177 mm]
19.00
[483 mm]
12.18
[309 mm]
25.00
[635 mm]
25.38
[645 mm]
13.25
[337 mm]
14.00
[356 mm]
12.25
[311 mm]
14.58
[370 mm]
3.51
[89 mm]
5.25
[133 mm]
11.60
[295 mm]
Acheron Designer
Weight
Without Grille Frame
76.0 lbs (34.5 kg)
With Grille Frame
78.0 lbs (35.4 kg)
Acheron Designer Dimensions
27
APPENDIX A: ACHERON DESIGNER SPECIFICATIONS
ø0.56
[ø14 mm]
14.96
[380 mm]
2.00
[51 mm]
19.00
[483 mm]
24.13
[613 mm]
6.96
[177 mm]
12.18
[309 mm]
29.82
[757 mm]
25.38
[645 mm]
27.62
[702 mm]
22.00
[559 mm]
9.00
[229 mm]
5.25
[133 mm]
Acheron Designer
Weight
3.00
[76 mm]
Acheron Designer Dimensions with MYA-DES Cradle-Style Yoke
28
Without MYA-DES Yoke
76.0 lbs (34.5 kg)
With MYA-DES Yoke
104.5 lbs (47.4 kg)
Meyer Sound Laboratories Inc.
2832 San Pablo Avenue
Berkeley, CA 94702
www.meyersound.com
T: +1 510 486.1166
F: +1 510 486.835
© 2012
Meyer Sound. All rights reserved.
Acheron Designer Operating Instructions, PN 05.211.005.01 A
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract, Print high-res Language : en Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : FrameMaker 10.0 Modify Date : 2012:04:23 11:51:18-07:00 Create Date : 2012:02:08 11:36:44Z Metadata Date : 2012:04:23 11:51:18-07:00 Format : application/pdf Title : Acheron Designer Operating Instructions Creator : gregt Subject : draft 5 Producer : Acrobat Distiller 10.0.0 (Windows) Keywords : draft 5 Document ID : uuid:4894034a-b4f1-4d6d-80db-f727c12f115b Instance ID : uuid:7a148272-b81b-47c9-9c3f-75c85c52ce0c Page Mode : UseOutlines Page Count : 32 Author : gregtEXIF Metadata provided by EXIF.tools