Micro Star MS6868F BT AUDIO TRANSMITTER User Manual USERS MANUAL
Micro Star International Co Ltd BT AUDIO TRANSMITTER USERS MANUAL
USERS MANUAL
FCC Caution 1. 2. 3. 4. The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. FCC Statement This device is intended only for OEM integrators under the following 1) The antenna must be installed such that 20 cm is maintained between antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not required. However, the OEM integrator is still responsible for testing end-product for any additional compliance requirements required with module installed (for example, digital device emissions, PC peripheral requirements, etc.). Important Note In the event that these conditions can not be example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid the FCC ID can not be used on the final product. In these circumstances, OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where antenna may be installed such that 20 cm may be maintained between antenna and users (for example access points, routers, wireless ADSL and similar equipment). The final end product must be labeled in a area with the following: “Contains TX FCC ID: GI4L-MS6868A/B”. Manual Information for End Users The end user must not have manual instructions to remove or install device. The user manual for end users must include the following information in a prominent location: “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located operating in conjunction with any other antenna or transmitter. as a result of e-mail transmission.” Important Safety Precautions Always read and follow these basic safety precautions carefully when handling any piece of electronic component. 1. Keep this User Guide for future reference. 2. Keep this equipment away from humidity. 3. Lay this equipment on a reliable flat surface before setting it up. 4. The openings on the enclosure are for air convection hence protects the equipment from overheating. 5. All cautions and warnings on the equipment should be noted. 6. Never pour any liquid into the opening that could damage or cause electrical shock. 7. If any of the following situations arises, get the equipment checked by a service personnel: Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipment has not work well or you can not get it work according to User Manual The equipment has dropped and damaged If the equipment has obvious sign of breakage 8. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 65°C OR BELOW -20°C, IT MAY DAMAGE THE EQUIPMENT. Bluetooth Audio Transmitter (MS-6868F) Introduction >>> 2.1 Appearance >>> 2.2 Features A Bluetooth Stereo Transmitter with 3.5mm earphone plug. General Features Standard Bluetooth SIG Specification v1.2 Support Profiles A2DP(Advanced Audio Distribution Profile) Interface 3.5mm line-in jack 1. CD-Quality, 44.1, 48KHz 16bits stereo Audio Function 2. Freq. Response: 20Hz~20KHz LED for Power and Mode/Link LED Indicator Frequency Band 2.400~2.4835GHz unlicensed ISM band Spectrum FHSS (Frequency Hopping Spread Spectrum) Modulation GFSK Output Power 0~4dbm Receiving Sensitivity -70dbm @<0.1% BER Power Class Class 2 Range 10m (Outdoor operating space) Antenna Chip Antenna RF Specifications Buttons Button for Power On/Off and Pairing Device will be auto-power off after 3 minutes in Auto-Power Off Low Battery Indicator standby mode. Blue LED blink Audio Format SBC Operating Temperature 0° ~ 50°C (32°F ~ 122°F ) Storage Temperature -20° ~ 65°C (-16°F ~ 149°F ) Power Source 1 x AAA Battery A2DP Music Mode: 6 hours Operating Time (Based on one 1000mA AAA battery). Certification CE, FCC, C-Tick, DGT Dimension 66(L)*25(W)*17.5(H)mm Weight 21g (without battery) Bluetooth Interface Blue Standard Bluetooth Specification v1.2 Profile A2DP RF Power Bluetooth Class 2 (0~4dBm) Chipset CSR BC03MM or equivalent Audio Codec Sub-Band Codec Distance 10meters (Outdoor operating space) Battery Installation Before power on the Bluetooth stereo transmitter, you have to install one AAA battery into it. >> How to install the battery? 1. Press the battery cover and slide it to your right/left side. 2. Open the battery cover and install the battery in the right position (+/-). Then take the cover to slide it to your right/left side to close the cover. >> How to uninstall the battery? 1. Press the battery cover and slide it to your right/left side. 2. Open the battery cover and take out the battery, then take the cover to slide it to your right/left side to close the cover. >>> 2.3 Control and Indications Function Key and LED indication Button required On Off press Blue LED (source) Description light up for 0.5 secs and After 2 minutes, if the source cannot find press and hold off, and then lights up and pair to a device, the source shuts for 3 secs down. permanently press and hold for light up for 3 quick flashes Power off headset; blinking sequence and off. similar to headset. 3 secs Link N/A Blinking 0.3 secs in every The LED indication is different with 4 secs) Pairing mode. Note: LED lights of FS120 uninterrupted indicating pairing process. Afterwards, LED shall turn to blinks (0.3 secs ON in every 4 secs) one another signifying link mode.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Extract Page Count : 8 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:913f530d-e729-48c9-b006-a2f712ce2e83 Producer : Acrobat Distiller 7.0 (Windows) Create Date : 2006:03:27 10:29:42+08:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2006:05:03 13:58:54+08:00 Metadata Date : 2006:05:03 13:58:54+08:00 Document ID : uuid:8c4b029a-c834-4028-ab5d-f771f299ab59 Instance ID : uuid:54cb2016-5083-4923-a662-79f362157570 Format : application/pdf Title : Microsoft Word - MS-6868E MS-6868F-EMI_English_.doc Creator : easonshen Author : easonshenEXIF Metadata provided by EXIF.tools