Micro Star MS6893 Wireless 802.11b/g/n 2T3R mini-PCI card User Manual 3

Micro Star International Co Ltd Wireless 802.11b/g/n 2T3R mini-PCI card 3

Users Manual

MSI MP11BGN (MS-6893) Wireless 11b/g/n 2T3R MiniPCI Card User’s Guide
General specification Network Standard IEEE 802.11n Draft 2.0 IEEE 802.11b IEEE 802.11g Frequency Band 2.400-2.4835 GHz Form factor Mini PCI v1.0 TypeⅢA Data Rate IEEE 802.11g (auto-fallback): - OFDM: 54, 48, 36, 24, 18, 12, 9 and 6 Mbps IEEE 802.11b (auto-fallback): - CCK: 11, 5.5 Mbps - DQPSK: 2 Mbps - DBPSK: 1 Mbps IEEE 802.11n Draft 2.0 (auto-fallback): - OFDM: 6.5 to 300 Mbps (Follow MCS 0~15 standard) Media Access Control CSMA/CA with ACK IEEE 802.11g/n IEEE 802.11b Ch. 1-11 – N. America Ch. 1-11 – N. America Ch. 1-13 – Japan Ch. 1-14 – Japan Ch. 1-13– Europe ETSI Ch. 1-13– Europe ETSI Ch. 10-11 – Spain Ch. 10-11 – Spain Channel Ch. 10-13 – France Ch. 10-13 – France Transmission IEEE 802.11b (DSSS)、IEEE 802.11g/n (OFDM) Modulation IEEE 802.11b (DSSS): CCK @ 11, 5.5 Mbps DQPSK @ 2 Mbps DBPSK @ 1 Mbps IEEE 802.11n Draft 2.0 (OFDM): OFDM @ 6.5 to 300 Mbps (Follow MCS 0~15 standard) IEEE 802.11g (OFDM): BPSK @ 6, 9 Mbps QPSK @ 12, 18 Mbps 16-QAM @ 24, 36 Mbps 64-QAM @ 48, 54 Mbps Network Architecture Ad-Hoc Mode (Peer-to-Peer) Infrastructure Mode Antenna Type Three antenna RF connectors configuration Temperature Operating Temperature 0° to 70°C
Storage Temperature -20° to 100°C Humidity 10%-90% (non-condensing) 802.11b (11Mbps): 660mA@3.3V in continue Tx / 520mA@3.3V in continue Rx 802.11g (54Mbps): 670mA@3.3V in continue Tx / 520mA@3.3V in continue Rx 802.11n Draft 2.0: HT20MHz:740mA@3.3V in continue Tx / 520mA@3.3V in continue Rx HT40MHz:740mA@3.3V in continue Tx / 520mA@3.3V in continue Rx Power Consumption 330mA@3.3V in standby mode Dimension 50.95*59.75*4.5mm Weight 14g Operating Voltage 3.3V+/-10% Output Power (Peak Max) 802.11g (54Mbps): 20.0+/-1 dBm 802.11b (11Mbps): 23.0+/-1 dBm 802.11n Draft 2.0: HT20MHz: 25.0+/-1 dBm / HT40MHz: 23.0+/-1 dBm Output Power (Average Max) 802.11g (54Mbps): 15.0+/-1 dBm 802.11b (11Mbps): 15.0+/-1 dBm 802.11n Draft 2.0: HT20MHz: 15.0+/-1 dBm / HT40MHz: 14.0+/-1 dBm Error Vector Magnitude (EVM) (Typical Value) 802.11g (54Mbps): <-25dB 802.11b (11Mbps): <35% 802.11n Draft 2.0: <-28dB Receiver Sensitivity (Typical Value) 802.11b (11Mbps): CCK @ 8% PER = -76 dBm 802.11g (54Mbps): OFDM @ 10% PER = -65 dBm 802.11n Draft 2.0: HT20 @ 10% PER = -64 dBm / HT40 @ 10% PER = -61 dBm Range Up to 400m (outdoor operating range) Security 64/128-bit WEP, WPA, WPA2, WPA-PSK, WPA2-PSK, 802.1X, CCX
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. RF exposure warning · This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Navigation menu