Microelectronics Technology RU-813 UHF RFID Reader User Manual CCCCCCCCCCCC
Microelectronics Technology Inc UHF RFID Reader CCCCCCCCCCCC
Manual
MTI RFID Reader
Operation Manual
- AS ISSUED Steven Kao
LTR. E.C.O. NO. DATE CHANGE INFORMATION AUTHOR
REVISED HISTORY
DWG NO. 43-RFID0900-E1-MANUAL APPROVED BY
台揚企業集團
MTI Group.
ISO 9001 Certified
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
PAGE NO. 1 OF 23 Eric Hsian
g
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
LTR. E.C.O. NO. DATE CHANGE INFORMATION AUTHOR
REVISED HISTORY
DWG NO. 43-RFID0900-E1-MANUAL
TITLE: MTI RFID Reader Operation Manual
MTI RFID Reader Operation Manual PAGE: 3
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
Contents
Chapter 1 – Introduction......................................................................................... 4
1.1 Purpose...................................................................................................... 4
1.2 Unpacking the Reader ............................................................................... 4
1.3 About the MTI RFID RU-813 Reader......................................................... 4
1.4 Federal Communication Commission Interference Statement................... 5
Chapter 2 – Installation .......................................................................................... 7
2.1 Antenna Installation ................................................................................... 7
2.2 Reader Mechanical Installation.................................................................. 9
2.2.1 Hollow Concrete Block Wall Mounting...........................................................10
2.2.2 Solid Concrete Wall Mounting
..........................................................................10
2.2.3 Wood or Metal Wall Mounting
...........................................................................10
2.2.4 Drywall Mounting
..............................................................................................11
2.3 Ethernet LAN Installation ......................................................................... 11
Chapter 3 – Configuration.................................................................................... 12
3.1 Ethernet Overview ................................................................................... 12
3.2 IP Address or Subnet Mask Setup........................................................... 12
3.3 Gateway Address Setup .......................................................................... 13
3.4 Destination Address and Destination Port Setup..................................... 13
3.5 Setup Password Setup ............................................................................ 14
Chapter 4 – Operation.......................................................................................... 15
4.1 Overview.................................................................................................. 15
4.2 Startup ..................................................................................................... 16
4.2 Version Identification................................................................................ 16
4.3. Operating ................................................................................................ 17
4.3.1 Function Tabs
...................................................................................................17
4.3.2 Status Bar
..........................................................................................................17
4.3.3 Connect
.............................................................................................................18
4.3.4 Read Tag Data
...................................................................................................18
4.3.5 Write Data to Tag
..............................................................................................20
Chapter 5 – Specification..................................................................................... 23
MTI RFID Reader Operation Manual PAGE: 4
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
Chapter 1 – Introduction
1.1 Purpose
This document provides users and technicians with instructions for installing and
operating the MTI RFID RU-813 Reader Application. The MTI RFID Reader
Application and associated documentation are provided as an aid for configuring
your MTI RFID reader and is not intended as an engineering design system.
1.2 Unpacking the Reader
After opening the shipping container perform the following:
1. Unpack the contents of container.
2. Inspect the shipping container for damage. If damaged, notify the carrier and
Microelectronic Technology Inc. Keep the shipping materials for inspection.
3. Verify your reader package includes the following items:
MTI RFID UHF RU-813 Reader
Antennas
SMA Male to SMA Male Antenna Cables
12 Vdc power adapter
Power Cord
System documentation CD
1.3 About the MTI RFID RU-813 Reader
The RU-813 is the MTI UHF RFID reader. This device currently supports many of
today’s most popular UHF tags including EPC G2. The device can read or write to
any tag depending on the tag capabilities. The RU-813 incorporates a scalable
architecture that enables the reader to be implemented as a stand-alone or
included in a networked reader environment using Ethernert LAN connection.
MTI RFID Reader Operation Manual PAGE: 5
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
1.4 Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
MTI RFID Reader Operation Manual PAGE: 6
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
MTI RFID Reader Operation Manual PAGE: 7
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
Chapter 2 – Installation
2.1 Antenna Installation
The RU-813 supports from one Tx/Rx to four Tx/Rx external antennas in a variety
of configurations. One- and two-antenna configurations are typical for most
conveyor and container tracking. Four-antenna configurations are used for portals
and loading dock doorways.
Tx
Rx
Figure 1 6dBi Flat Antenna Outline
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 8
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
The RU-813 is factory calibrated for operation with the following type of antenna
and cable:
Item Specification
Operating Frequency 902-928MHz
Impedance 50Ohm
VSWR <1.3
Polarization Circular
Gain 6dBi
Front to back ratio 20dB
Axial ratio 3dB
Connector SMA Female
Dimension 140 x140 x30mm
The RU-813 is factory configured to operate with one Tx/Rx antenna connected
to Port Tx1/Rx1. However, the reader can operate with up to four Tx/Rx
antennas. If additional antennas are to be installed, use RF Command Suite to
select the number of antennas in figure 2.
Antenna RF Ports
One Tx /Rx Select Port : Tx 1 , Rx 1
Two Tx /RX Select Port : Tx 1 , Rx 1, Tx 2 , Rx 2
Three Tx /Rx Select Port : Tx 1 , Rx 1, Tx 2 , Rx 2, Tx 3 ,Rx 3
Four Tx/ Rx Select Port : Tx 1 , Rx 1, Tx 2 , Rx 2, Tx 3 ,Rx 3 ,Tx 4 , Rx 4
Figure 2 Antenna Port Selection Table
It is highly recommended that the antenna mounting be adjustable in order to
obtain the best performance from the system. However, the antennas must be
installed on a solid surface or frame to prevent damage or later misalignment.
Perform the following to install the antennas.
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 9
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
2.2 Reader Mechanical Installation
TheRU-813 is designed for easy installation. The following instructions provide
the information to install your UHF reader.
As shown in figure 3, the reader is designed for horizontal installation. Mounting
keyholes are provided on each side of the base plate for easy, non- permanent,
installation and removal in figure 4.
Figure 3 RU-813 Reader Installation
Figure 4 RU-813 Base Plate with Mounting Keyholes
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 10
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
2.2.1 Hollow Concrete Block Wall Mounting
To temporarily mount theRU-813 to a hollow concrete block wall, MTI
recommends metal sleeve type concrete anchors that accept a #10 screw
and flat washer. To install the reader on a hollow concrete block wall, perform
the following.
1. Refer to Figure 4, and mark the location of the mounting screws. Do not
install the anchors into the mortar joint.
2. Drill the appropriate size hole for a metal sleeve type anchor.
3. Install the anchors.
4. Install the washers and insert the screws.
5. Tighten the screws to within .375” of the anchor.
6. Install the reader and finish tightening the screws.
2.2.2 Solid Concrete Wall Mounting
To temporarily mount theRU-813 to a solid concrete wall, MTI recommends
one-piece expansion type concrete anchors that accept a #10 screw and flat
washer. To install the reader on a concrete wall, perform the following.
1. Refer to Figure 4, and mark the location of the mounting screws.
2. Drill the appropriate size hole for a expansion type anchor and install the
anchors.
3. Install the washers and insert the screws.
4. Tighten the screws to within .375” of the anchor.
5. Install the reader and finish tightening the screws.
2.2.3 Wood or Metal Wall Mounting
To temporarily mount the RU-813 to a wood or sheet metal wall, MTI
recommends either #10 x 1 inch wood screws or #10 x 3/4 inch sheet metal
screws and washers. To install the reader on a wood or metal wall, perform
the following.
MTI RFID Reader Operation Manual PAGE: 11
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
1. Refer to Figure 4, and mark the location of the mounting screws.
2. Drill the appropriate size hole for screws.
3. Install the washers and insert the screws.
4. Tighten the screws to within .375” of the surface.
5. Install the reader and finish tightening the screws.
2.2.4 Drywall Mounting
To temporarily mount the RU-813 to drywall or sheetrock, MTI
recommends either #10 toggle bolts or #10 drywall anchors.
2.3 Ethernet LAN Installation
The RU-813 can be networked with other readers on an enterprise 10/100 BaseT
Ethernet LAN with crossover Ethernet cable. The IP address can then be accessed
by your network server or host computer, please refer to chapter 3 for further
information.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
Ethernet Port
Power Port
Figure 5 Installation
MTI RFID Reader Operation Manual PAGE: 12
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
Chapter 3 – Configuration
3.1 Ethernet Overview
When the reader is installed on a TCP/IP network connected to the internet, the
reader must be assigned a unique IP address. The default IP address is set as
192.168.1.200, and the default subnet mask is set as 255.255.255.0, when the
reader is shipped from factory. All these can be set by using web browser.
Beside, the gateway, destination IP address, destination port, and setup password
can be set as the same way as above.
. Note:
The default setting of destination IP address is set as 192.168.1.39
The default setting of destination port is set as 100
The default setting for the setup password is set as empty.
3.2 IP Address or Subnet Mask Setup
To set up IP address of RU-813 for Ethernet communication, perform the following
steps:
1. Verify all cables and power supplies are secure and power up the readers.
2. Set the subnet mask of host computer to the same subnet domain of reader.
3. Open Web browser (IE or Netscape) on your host computer.
4. Type IP address at web address on the browser.
5. Enter password (the default password is empty), then click “Login”.
6. Change IP address.
7. Change subnet mask, if necessary.
8. Click “Update”
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 13
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
3.3 Gateway Address Setup
To set up IP address of RU-813 for Ethernet communication, perform the following
steps:
1. Verify all cables and power supplies are secure and power up the readers.
2. Set the subnet mask of host computer to the same subnet domain of reader.
3. Open Web browser on your host computer.
4. Type IP address at web address on the browser.
5. Enter password, then click “Login”.
6. Chang Gateway address
7. Click “Update”
3.4 Destination Address and Destination Port Setup
To set up destination address and destination port of RU-813 for Ethernet
communication, perform the following steps:
1. Verify all cables and power supplies are secure and power up the readers.
2. Set the subnet mask of host computer to the same subnet domain of reader.
3. Open Web browser on your host computer.
4. Type IP address at web address on the browser.
5. Enter password, then click “Login”.
6. Chang destination address and destination port
7. Click “Update”
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 14
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
3.5 Setup Password Setup
To set up password of RU-813 for Ethernet communication, perform the following
steps:
1. Verify all cables and power supplies are secure and power up the readers.
2. Set the subnet mask of host computer to the same subnet domain of reader.
3. Open Web browser on your host computer.
4. Type IP address at web address on the browser.
5. Enter password, then click “Login”.
6. Chang setup password
7. Click “Update”
Note: Once the Setup password is changed, the new password will be
required for next login process.
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 15
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
Chapter 4 – Operation
4.1 Overview
The RFID Reader Application is a Microsoft Windows application that provides a
Graphical User Interface (GUI) for MTI RFID Reader Products.
Figure 6 Overview of MTI RFID Reader Application
Functions provided by the RFID Reader Application include the following:
View tag data
Write data to tag
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 16
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
4.2 Startup
MTI RFID Reader Application can communicate with all MTI readers through the
Ethernet (TCP/IP) port. Verify your reader is connected to the correct port and
power up.
After connect power cord, the PWR LED light on the shell of reader will turn on. As
figure 7.
Figure 7
To start up MTI RFID Reader Application, perform the following:
1. Execute RFID DEMO AP.exe
2. The application will attempt to connect to using the most recent configuration
settings.
Note:
The destination port for this application is required to set as 100, please refer
to chapter 3 for Ethernet configuration setting.
4.2 Version Identification
To determine the current version of your MTI RFID Reader Application, refer to
the status bar below the application.
Figure 8 Current version of the application
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 17
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
4.3. Operating
4.3.1 Function Tabs
RFID Reader Application operations are divided into two functional interfaces
selected by tabs at the top of the display.
Figure 9 functional tabs
Read Function: Read tag data.
Write Function: Write data to tag
4.3.2 Status Bar
At the application below, the status bar provide the information of the
operation.
Connection
message version
RF Power
Figure 10 Status bar
Connection light:
Red: no connect
Green: connected
RF Power light:
Red: RF off
Yellow: RF On
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 18
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
4.3.3 Connect
Before read/write tag, you need to establish connection between PC and
reader. Use [Connect] button to connect to reader. If application does not
connect, verify the PC and reader’s Ethernet network setting. Please refer to
Chapter 3 for further information
network PC
IP address 192.168.1.39
Subnet mask 255.255.255.0
Reader
IP address 192.168.1.200
port 100
4.3.4 Read Tag Data
To display tag data as the data is received from the reader by clicking the RF
On button. When tags are read, they are displayed in the window and the
statistics are updated.
When reader accepted the RF On command from computer, the TX LED light
on the shell of reader will turn on. On the other hand, TX LED light will turn off
when RF OFF. As following figure.
RF ON RF OFF
Figure 11
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 19
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
During the RF On period, if reader receive the response signal from tag, the
RX LED light on the shell of reader will flash one time.
Figure 12 RX LED light
The Tag Read Time displayed in the lower window is the total tag read count
since the last reset. The Antenna No is the tag be read by which Tx/Rx
antenna.
Figure 13 display tag data
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI RFID Reader Operation Manual PAGE: 20
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
4.3.5 Write Data to Tag
Step 1: Select which antenna to write data to tag.
Step 2: Click the Scan button to search the tag in the range of antenna.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
MTI RFID Reader Operation Manual PAGE: 21
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
Step 3: Fill up the four columns of the new tag ID.
Step 4: Click the Lock button, then the button will change to Unlock.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
MTI RFID Reader Operation Manual PAGE: 22
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
Step 5: Click the Write Tag button.
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
Step 6: If write command success done, click Unlock to re-scan. And the new
tag ID will display.
MTI RFID Reader Operation Manual PAGE: 23
43-RFID0900-E1-MANUAL DATE: 18-04-2006
台揚集團智慧財產
任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害
台揚集團之智慧財產權，將可因此負擔法律責任。
MTI Group Proprietary Information
Any unauthorized use, duplication, reproduction, or disclosure of this document may be
considered as infringement of MTI Group’s intellectual property rights, the infringer may
be accused and liable applicable legal penalties.
台揚科技股份有限公司
MICROELECTRONICS TECHNOLOGY INC.
ISO 9001 Certified
Chapter 5 – Specification
This chapter describes the specification for MTI RFID RU-813 Reader
Operating Frequency 910-920 MHz
RF output power 29dBm
RFID protocol EPC C1G2 V1.09
Humility 0~99% Non-Condensing
Modulation Amplitude Modulation
Operation Channels 51
Occupied Channel 20dB Bandwidth 200KHz
Operating Temperature -20 ~ +50 degree C
Storage Temperature -40 ~ +70 degree C
Antena 8 port TX/RX Separate for 4 reading points/
6 dBi circular polarization
Power Supply 12VDC/Max 2A
Communication interface RJ45
LAN Interface Ethernet/TCP/IP
Indicators Power/TX/RX
Dimension 230 mm x 264 mm x 40mm
Weight 1.365 kG /2.989 lb