Microhard Systems 12XBG24-30 MiniPCI BG 1W 2.4GHz User Manual XBG24 30

Microhard Systems Inc MiniPCI BG 1W 2.4GHz XBG24 30

(XBG24-30) User Manual_20120413

Features • IEEE 802.11 b/g standard compliant • Output Power of up to 30dBm @ b/g Band with built-in ESD Protection • RF ESD/EMP Immunity Threshold: 15KeV ① • Supports Atheros Proprietary "Super Mode" delivering up to 108 Mbps data link rate • Transmission Power Control (IEEE 802.11h TPC) • Extended distances and high performance due to optimized output signal power • Multi-Country Roaming Supported (IEEE802.11d Global Harmonization Standard) • Single MMCX antenna connector allowing for improved mechanical stability and low loss • Ideal for long-distance, outdoor broadband wireless applications MiniPCI BG 1W 2.4GHz XBG24-30
TECHNICAL SPECIFICATIONS Chipset Atheros 2414 Host Interface PCI Interface v2.3 (Type III-B Mini PCI form factor) Operating Voltage 3.3 VDC 11b Cont. Tx@5.5M 5.0W 11g Cont. Tx@6M 5.5W 11g Cont. Rx 2.5W Power Consumption Standby 1.5W Antenna Connector 1×MMCX (main) IEEE 802.11b： 11Mbps 5.5 Mbps 2 Mbps 1 Mbps IEEE 802.11g: 54Mbps 48Mbps 36Mbps 24Mbps 18Mbps 12Mbps 9Mbps 6Mbps Data Rates Super-G: 108Mbps 96Mbps 72Mbps 54Mbps 48Mbps 36Mbps 24Mbps 18Mbps 12Mbps 6Mbps 2.412GHz ~ 2.462GHz (US & Canada) 2.412GHz ~ 2.472GHz (Europe) Frequency Range IEEE 802.11b/g: 2.412GHz ~ 2.484GHz (Japan) Modulation Techniques OFMD: BPSK, QPSK, 16-QAM, 64-QAM DSSS: DBPSK, DQPSK, CCK Certification FCC RoHS Compliance Yes Temperature Range Operating: -20ºC to 70ºC Storage: -40 ºC to 90 ºC Humidity Operating: 5% to 95% (non-condensing) Storage: Max.90% (non-condensing) Dimensions 64.3 mm x 47 mm x 14 mm XBG24-30 MINIPCI CARD RADIO SPECIFICATIONS TX SPECIFICATIONS RX SPECIFICATIONS DataRate TX Power Tolerance DataRate Sensitivity Tolerance1Mbps 30dBm +1.0/-1.5 dB 1Mbps -96dBm ±2dB2Mbps 30dBm +1.0/-1.5 dB 2Mbps -93dBm ±2dB5.5Mbps 30dBm +1.0/-1.5 dB 5.5Mbps -91dBm ±2dB802.11b 11Mbps 30dBm +1.0/-1.5 dB 802.11b 11Mbps -90dBm ±2dB6Mbps 30dBm +1.0/-1.5 dB 6Mbps -93dBm ±2dB9Mbps 30dBm +1.0/-1.5 dB 9Mbps -90dBm ±2dB12Mbps 30dBm +1.0/-1.5 dB 12Mbps -89dBm ±2dB18Mbps 30dBm +1.0/-1.5 dB 18Mbps -87dBm ±2dB24Mbps 30dBm +1.0/-1.5 dB 24Mbps -84dBm ±2dB36Mbps 28dBm +1.0/-1.5 dB 36Mbps -80dBm ±2dB48Mbps 27dBm +1.0/-1.5 dB 48Mbps -76dBm ±2dB802.11g 54Mbps 25dBm +1.0/-1.5 dB 802.11g 54Mbps -74dBm ±2dB ESD CABLE SPECIFICATIONS Physical Dimensions 26cm length Terminal Material Copper Attachment Procedure End of ESD Cable tied to Earth Ground
ORDERING INFORMATION② CODES SPEED Carton Dimensions XBG24-30 Up to 108 Mbps For 50pcs (pcs/ctn), 0.40m * 0.22m * 0.085m / 0.006 = 1.5KG ① Comes with grounding cable ② Configurations are subject to change without notice DIMENSIONS DRAWING
Compliance Information FCC Compliance Statement: This device complies with Part 15 of the FCC Rules . Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This device must accept any interference received, including interference that may cause undesired operation. Product that is a radio transmitter is labeled with FCC ID. FCC Caution: (1) Exposure to Radio Frequency Radiation. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. (2) Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. (3) This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. (4) Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. NOTE: (1) This device is approved for OEM installation with specified antennas as listed in this Manual. It is the responsibility of the Installer to comply with the separation distance for satisfying RF exposure compliance. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. IC Radiation Exposure Statement for Canada: This device complies with Industry Canada licence-exempt RSS standard(s).
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. (1) the modules FCC ID is notvisible when installed in the host, or (2) if the host is marketed so that end users do not havestraightforward commonly used methods for access to remove the module so that the FCC ID ofthe module is visible; then an additional permanent label referring to the enclosed module:Contains Transmitter Module FCC ID : NS912XBG24-30 or Contains FCC ID: NS912XBG24-30mustbe used. Microhard Systems Inc Address: 150 Country Hills Landing NW Calgary Alberta Canada Contact Name: Hany Shenouda Tel. No: 403-248-0028 Fax No: 403-248-2762 Email: shenouda@microhardcorp.com

Navigation menu