Microhard Systems 12XN58-26 HIGH POWER N MINIPCI 5.8GHz User Manual XN58 26 120323

Microhard Systems Inc HIGH POWER N MINIPCI 5.8GHz XN58 26 120323

Users Manual

Download: Microhard Systems 12XN58-26 HIGH POWER N MINIPCI 5.8GHz User Manual XN58 26  120323
Mirror Download [FCC.gov]Microhard Systems 12XN58-26 HIGH POWER N MINIPCI 5.8GHz User Manual XN58 26  120323
Document ID1662099
Application IDVAmZRaspMn+v95djBBKYgA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize31.42kB (392758 bits)
Date Submitted2012-03-23 00:00:00
Date Available2012-03-23 00:00:00
Creation Date2012-03-22 15:40:49
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2012-03-22 15:40:49
Document TitleMicrosoft Word - XN58-26_User Manual_120323.doc
Document CreatorPScript5.dll Version 5.2
Document Author: Administrator

High Power N MiniPCI 5.8GHz
2 x 2 802.11N MIMO mini-PCI Modules
XN58-26
5GHz Single-Band 802.11n MIMO 2 x 2 miniPCI
Features
•
•
•
•
•
•
Atheros XSPAN family chipset
•
•
•
Built-in ESD Protection with ESD/EMP Immunity Threshold: 15KeV
IEEE 802.11n compliant and backward compatible with 802.11a
Enhanced sensitivity
Optimized isolation path
Superior thermal performance
Maximum output power 26dBm@802.11a / 28dBm MIMO aggregate
①
Multi-Country Roaming Supported (IEEE802.11d Global Harmonization Standard)
2 x MMCX connectors allowing for improved mechanical stability and low loss
Technical Specifications
Chipset
Host Interface
Operating
Voltage
Atheros AR9220
32-bit mini-PCI Type IIIA+ (6.55mm longer than IIIA type)
3.3 VDC
Power
Consumption
11a Cont. Tx @6M
11na Cont. Tx@HT20 MCS0
11na Cont. Tx@HT40 MCS0
11a Cont. Rx
Standby
Antenna
Connector
2 x MMCX connector
IEEE 802.11a :
Data Rate
IEEE 802.11n :
Frequency
Range
IEEE 802.11a/n:
Modulation
Techniques
RoHS
Compliance
Temperature
Range
Humidity
Dimension
4.9W
4.3W
4.8W
2.5W
0.8W
54Mbps 48Mbps 36Mbps 24Mbps 18Mbps 12Mbps 9Mbps
1Nss: 65Mbps @ 800GI, 72.2Mbps @ 400GI (Max.)
20MHz
2Nss: 130Mbps @ 800GI, 144.4Mbps @ 400GI (Max.)
1Nss: 135Mbps @ 800GI, 150Mbps @ 400GI (Max.)
40MHz
2Nss: 270Mbps @ 800GI, 300Mbps @ 400GI (Max.)
5.725 ~ 5.850 GHz (US & Canada)
5.725 ~ 5.875 GHz (Europe)
6Mbps
OFDM: BPSK, QPSK, 16-QAM, 64-QAM
Yes
Operating: -20ºC to 70ºC
Storage: -40ºC to 90ºC
Operating:5% to 95% (non-condensing)
Storage: Max.90% (non-condensing)
59.6mm x 57.5mm x 7.5mm
XN58-26 MIMO MINIPCI CARD RADIO
DataRate
802.11a
5GHz
11n
HT 20
TX Power
TX Power
MCS 0/8
MCS 1/9
MCS 2/10
MCS 3/11
MCS 4/12
MCS 5/13
MCS 6/14
MCS 7/15
25dBm
25dBm
23.5dBm
23.5dBm
22.5dBm
22dBm
21dBm
20dBm
28dBm
28dBm
26.5dBm
26.5dBm
25.5dBm
25dBm
24dBm
23dBm
802.11a
5GHz
11n
HT 20
6M
9M
12M
18M
MCS0
MCS1
MCS2
MCS3
MCS4
MCS5
MCS6
MCS7
(per chain)
6-24Mbps
36Mbps
48Mbps
54Mbps
DataRate
DataRate
TX SPECIFICATIONS
TX Power
(per chain)
(2 chains)
TX Power
Tolerance
28dBm
28dBm
27dBm
26dBm
±2dB
±2dB
±2dB
±2dB
(2 chains)
26dBm
25dBm
24dBm
23dBm
Tolerance
DataRate
±2dB
±2dB
±2dB
5GHz
±2dB
11n
±2dB
HT 40
±2dB
±2dB
±2dB
RX SPECIFICATIONS
MCS 0/8
MCS 1/9
MCS 2/10
MCS 3/11
MCS 4/12
MCS 5/13
MCS 6/14
MCS 7/15
TX Power TX Power
(per chain)
(2 chains)
24dBm
24dBm
22.5dBm
22.5dBm
22dBm
20.5dBm
20.5dBm
17dBm
27dBm
27dBm
25.5dBm
25.5dBm
25dBm
23.5dBm
23.5dBm
20dBm
Tolerance
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
Sensitivity
Tolerance
DataRate
Sensitivity
Tolerance
-96dBm
-96dBm
-95dBm
-93dBm
-95dBm
-93dBm
-90dBm
-89dBm
-85dBm
-81dBm
-79dBm
-75dBm
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
24M
36M
48M
54M
MCS0
MCS1
MCS2
MCS3
MCS4
MCS5
MCS6
MCS7
-89dBm
-86dBm
-82dBm
-79dBm
-92dBm
-90dBm
-87dBm
-84dBm
-81dBm
-77dBm
-76dBm
-74dBm
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
±2dB
(2 chains)
802.11a
5GHz
11n
HT 40
(2 chains)
ESD CABLE SPECIFICATION
26cm length
Copper
End of ESD Cable tied to Earth Ground
Cable Dimensions
Terminal Material
Attachment Procedure
②
Ordering Information
CODES
Connectors type
XN58-26
MMCX
Carton Dimension
For 50pcs (pcs/ctn), 0.40m * 0.22m * 0.085m / 0.006 = 1.5KG
For 250pc (pcs/ctn), 0.45m * 0.45m * 0.24m / 0.006 = 8.1KG
Module grounding cable included
Configurations are subject to change without notice
Please contact Compex sales representatives for other available configurations
COMPLIANCE INFORMATION
This device complies with the following radio frequency and safety standards.
Important to OEM Manufacturer:
This following FCC Warning must be included in the HOST User Manual.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance.
Note 1: This module certified that complies with RF exposure requirment under mobile or fixed condition,
this module is to be installed only in mobile or fixed applications.
A mobile device is defined as a transmitting device designed to be used in other than fixed
locations and to generally be used in such a way that a separation distance of at least 20
centimeters is normally maintained between the transmitter's radiating structure(s) and the
body of the user or nearby persons. Transmitting devices designed to be used by consumers or
workers that can be easily re-located, such as wireless devices associated with a personal
computer, are considered to be mobile devices if they meet the 20 centimeter separation
requirement.
A fixed device is defined as a device is physically secured at one location and is not able to be
easily moved to another location.
Note 2: Any modifications made to the module will void the Grant of Certification, this
module is limited to OEM installation only and must not be sold to end-users, end-user has no
manual instructions to remove or install the device, only software or operating procedure shall
be placed in the end-user operating manual of final products.
Note 3: The device must not transmit simultaneously with any other antenna or transmitter.
Note 4: To ensure compliance with all non-transmitter functions the host manufacturer is
responsible for ensuring compliance with the module(s) installed and fully operational. For
example, if a host was previously authorized as an unintentional radiator under the
Declaration of Conformity procedure without a transmitter certified module and a module is
added, the host manufacturer is responsible for ensuring that the after the module is installed
and operational the host continues to be compliant with the Part 15B unintentional radiator
requirements. Since this may depend on the details of how the module is integrated with the
host, Microhard System Inc. shall provide guidance to the host manufacturer for compliance
with the Part 15B requirements.
Note 5: FCC ID label on the final system must be labeled with “Contains FCC ID:
NS912XN58-26” or “Contains transmitter module FCC ID: NS912XN58-26”.
The transmitter module must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the host product.
Microhard Systems Inc. is responsible for the compliance of the module in all final hosts.
IMPORTANT NOTE REGARDING ANTENNA USE
Antenna Use (Point to Multipoint)
2x2 Operation
Chain1
Chain2
Dimensions Drawing
Microhard Systems Inc
Address: 150 Country Hills Landing NW Calgary Alberta Canada
Contact Name: Hany Shenouda
Tel. No: 403-248-0028
Fax No: 403-248-2762
Email: shenouda@microhardcorp.com
For more information, visit www.compex.com.sg

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2012:03:22 15:40:49+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2012:03:22 15:40:49+08:00
Format                          : application/pdf
Title                           : Microsoft Word - XN58-26_User Manual_120323.doc
Creator                         : Administrator
Document ID                     : uuid:e7477695-5d36-4008-a375-cf00ccd376c9
Instance ID                     : uuid:ad6905f7-d21c-4248-8366-50943f8a5ee9
Page Count                      : 7
Author                          : Administrator
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NS912XN58-26

Navigation menu