Microlab Electronics BOLT100 BLUETOOTH EARPHONE User Manual 80 Bolt100 97 0001 US 01

Microlab Electronics Co.,Ltd. BLUETOOTH EARPHONE 80 Bolt100 97 0001 US 01

UserManual.wiki >

Microlab Electronics >

BOLT100 User Manual

User Manual

15. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, ﬁre or the like.16.This lightning ﬂash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage”within the product’ s enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock.Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualiﬁed personnel.The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.17. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.18. No naked ﬂame sources, such as lighted candles, should be placed on the apparatus.19. Replacement parts - When replacement parts are required, ensure the service technician has used replacement parts speciﬁed by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in ﬁre, electric shock or other hazards.20. Try to install the product near a wall socket or extension cord and shall be easily accessible.21. The highest environmental temperature suitable for this product is 0℃ to 35℃ for indoor use only .IMPORTANT SAFETY INSTRUCTIONS1. Read these instructions – All the safety and operating instructions should be read before this product is operated.2. Keep these instructions – The safety and operating instructions should be retained for future reference.3. Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.4. Follow all instructions – All operating and use instructions should be followed.5. Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet basement or near a swimming pool, and the like.6. Clean only with dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacture’s instructions.8. Do not install near any heat sources such as radiators, heat registers, stoves, orother apparatus (including ampliﬁers) that produce heat.9. Only use attachments/accessories speciﬁed by the manufacturer.10. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.11. Unplug the apparatus during lightning storms or when unused for long periods of time.12. Refer all servicing to qualiﬁed personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.13. WARNING: To reduce the risk of ﬁre or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects ﬁlled with liquids, such as vases, shall not be placed on apparatus.14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIRRISK OF ELECTRIC SHOCK DO NOT OPENThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.FCC and Canada EMC Compliance IinformationFCC ID:OR8-BOLT 100IC:21231-BOLT100Warning1.DO NOT expose product to extreme temperatures, moisture or electric shock2.DO NOT attempt to open this product for any reason. 3.DO NOT attempt to manipulate any electrical components into this product4.DO NOT attempt to use if internal components have been exposed to liquidPackage includes1.1× Bluetooth Headphone Unit2.1× Micro USB Charging Cable3.3×Sets Of Ear Buds (L/M/S size) one is on the headset4.1×User Manual Manual contents1.Speciﬁcations2.Parts3.How to charge Bluetooth Headphone4.How to connect Bluetooth Headphone5.How to use Bluetooth Headphone6.Frequently Asked Questions Parts How to Charge the Headphones Turn On the earphone:When power off status, press and hold the “Power on” button for two seconds, the indicator light ﬂashes in blue color. How to Use Bluetooth Headphones1.Press “+” button to increase volume, press and hold “+” button to previous audio ﬁle.2.Press “-” button to decrease the volume, press and hold “-” to next audio ﬁle3.Press “Power” button to answer or hang off a calling when on a phone call4.Press “Power” button to pause or start a audio ﬁle when play back audio5.Press “Power” button and hold for about 2-3 seconds until the indicator ﬂashes twice in red to turn off the Bluetooth headphone, at the same time you can hear a voice prompt, “Power off” How to Connect this Bluetooth Headphone with a Mobile Phone Frequently Asked QuestionsFailure to connect to Bluetooth-enabled devices might be caused by:Other Bluetooth devices are paired or sync mode are interfering with your connections. Please remove other devices from the vicinity or turn them offStatic or mufﬂed sound can be caused by any of the following:There are major Bluetooth obstructions between your devices and the headphoneThe distance of connection is over than 10 meters or there are obstacle between this headphone and your mobile phone.SupportHSP, HFP, A2DP,AVRCPFrequency Range2.4 GHzTransmitting PowerClass 2Working DistanceAbout 10 metersCharging Timeabout 1 hourTalk time 5-6hours Playback time5-6 hoursStandby time180 hours1.A rechargeable battery is built-in the Bluetooth headphones2.Please charge at least 2 hours before the ﬁrst usuage.3.The red indicator light will be on when the product is been charged. After fully charged, the indicator will change to blue.NOTE :Only a 5V DC charger or computer USB port can be used as the power supply to charge this headphone. This headset is charged from a micro USB port.Speciﬁcations Bolt1001.3.2.When phone is off, press and hold the “Power On” button for 3 seconds. The indicator light will flash blue, at the same time you will hear a voice prompt. Hold the "Power On" button for 2 more seconds. The light will flash red and blue showing that it's ready to pair. At the same time you will hear the voice prompt, “Ready to pair”. Turn on the Bluetooth function on your smart/mobile phone or search for the Bluetooth on other devices as the ID: Bolt 100, then pair it. It will show on your mobile phone if pairedsuccessfully. You will also hear a voice prompt, “your headset paired, connected”. Please proceed to play audio or make hands-free call.This Bluetooth headphone can be re-connected automatically with smart phone if they have been paired before. Just press the "Power on button for 3 seconds and it will pair with the phone automatically.