EZ Match Imager User's Manual Ezmatchmanual
2010-05-18
: Microscan Ezmatchmanual ezmatchmanual 6cd11823-0264-48b4-9c01-a17b8b3c1f25 _att
Open the PDF directly: View PDF
Page Count: 431 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- EZ Match User’s Manual
- Table of Contents
- About the EZ Match Imager
- About This Manual
- Highlighting
- Host Communications
- Warning and Caution Summary
- Statement of Agency Compliance
- Statement of RoHS Compliance
- 1 Quick Start
- Step 1 - Check Hardware
- Step 2 - Connect the System
- Step 3 - Position the Imager
- Step 4 - Install ESP
- Step 5 - Select Model
- Step 6 - Select Protocol and Connect
- Step 7 - Locate the Object in the Field of View
- Step 8 - Calibrate
- Step 9 - Test Read Rate
- Step 10 - Configure the Imager in ESP
- Step 11 - Save Configuration in ESP
- 2 Using ESP
- 3 Tube/Cap Inspection
- 4 Communications
- Communications by ESP
- Communications Serial Commands
- Host Port Connections
- Host Protocol
- Poll Address
- ACK / NAK Options
- Polling Mode Options
- RS-422 Status
- Auxiliary Port Connections
- Auxiliary Port System Data Status
- Daisy Chain Autoconfigure
- Response Timeout
- LRC Status
- Protocol Configuration Examples
- USB HID Interface
- ASCII Character Entry Modifier
- Preamble
- Postamble
- 5 Calibration
- 6 Read Cycle
- 7 Symbologies
- 8 I/O Parameters
- I/O Parameters by ESP
- I/O Parameters Serial Commands
- Symbol Data Output
- No Read Message
- Bad Symbol Message
- No Symbol Message
- 1D / Stacked Symbology Qualification
- 2D Symbology Qualification
- Read Duration Output
- Output Indicators
- Beeper
- LED Configuration
- Serial Verification
- EZ Button
- EZ Button Modes
- Configurable Output 1
- ISO/IEC 16022 Symbol Quality Output 1
- Diagnostics Output 1
- Tube/Cap Detection Output 1
- Configurable Output 2
- Trend Analysis Output 2
- ISO/IEC 16022 Symbol Quality Output 2
- Diagnostics Output 2
- Tube/Cap Detection Output 2
- Configurable Output 3
- Trend Analysis Output 3
- ISO/IEC 16022 Symbol Quality Output 3
- Diagnostics Output 3
- Tube/Cap Detection Output 3
- Frame Information
- Image Output
- Database Identifier Output
- Quality Output
- Power On / Reset Counts
- Time Since Reset
- Service Message
- EZ Trax Output
- 9 Symbol Quality
- 10 Matchcode
- 11 Camera and IP Setup
- Camera and IP Setup by ESP
- Camera and IP Setup Serial Commands
- Video
- Evaluation
- Calibration
- Window of Interest
- IP Database
- Dynamic Setup
- Camera Settings
- Focal Distance (Read-Only)
- Focal Distance Table (Read-Only)
- Pixel Sub-Sampling
- IP Threshold
- IP Mode
- Tube/Cap Mode
- Image Processing Timeout
- Background Color
- Mirrored Image
- Hollow Mode
- Number of Symbols in Field of View
- Damaged Symbol Status
- Illumination Brightness
- Skew Correction
- Color Filter (EZ Match Color Only)
- Color Detection (EZ Match Color Only)
- 12 IP Database
- 13 Terminal
- 14 Utilities
- 15 Output Format
- Appendices
- Appendix A - General Specifications
- Appendix B - Electrical Specifications
- Appendix C - Serial Configuration Commands
- Appendix D - Communications Protocol
- Appendix E - ASCII Table
- Appendix F - Interface Standards
- Appendix G - Using an External Trigger
- Appendix H - Operational Tips
- Appendix I - USB-to-Serial Virtual COM Port Driver
- Appendix J - Glossary of Terms
- Index