Microsoft BH-217 Bluetooth headset User Manual Nokia BH 217 UG en

Microsoft Mobile Oy Bluetooth headset Nokia BH 217 UG en

Manual

Nokia Bluetooth Headset BH-217Issue 178135246
12141391110
ENGLISHDECLARATION OF CONFORMITYHereby, NOKIA CORPORATION declares that this BH-217 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/phones/declaration_of_conformity/.© 2010 Nokia. All rights reserved.Nokia, Nokia Connecting People and the Nokia Original Accessories logo are trademarks or registered trademarks of Nokia Corporation. Nokia tune is a sound mark of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.Reproduction, transfer, distribution, or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice.Bluetooth is a registered trademark of Bluetooth SIG, Inc.To the maximum extent permitted by applicable law, under no circumstances shall Nokia or any of its licensors be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at any time without prior notice.The availability of products may vary by region. For more information, contact your Nokia dealer. This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited.
ENGLISHIntroductionWith the Nokia Bluetooth Headset BH-217, you can make and answer calls hands-free with your compatible mobile device.Read this user guide carefully before using the headset. Also, read the user guide for the device that you connect to the headset.This product may contain small parts. Keep them out of the reach of small children.Warning: The connector of the clip and car cradle may contain a small amount of nickel. Persons who are sensitised to nickel may have symptoms from prolonged skin contact with the connector.Bluetooth wireless technologyBluetooth wireless technology allows you to connect compatible devices without cables. The headset and the other device do not need to be in line of sight, but they should be within 10 metres (33 feet) of each other. Connections may be subject to interference from obstructions, such as walls, or other electronic devices.The headset is compliant with the Bluetooth Specification 2.1 + EDR supporting the Headset Profile 1.1 and Hands-Free Profile 1.5. Check with the manufacturers of other devices to determine their compatibility with this device.
ENGLISHGet startedThe headset contains the following parts shown on the title page: multifunction key (1), earloop (2), indicator light (3), earpiece (4), microphone (5), and charger connector (6).Before using the headset, you must charge the battery and pair the headset with a compatible device.Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic storage media near the device, because information stored on them may be erased.Charge the batteryBefore charging the battery, carefully read “Battery and charger information”.1. Connect the charger to a wall outlet.2. Connect the charger cable to the charger connector.To charge the headset when it is in the clip or car cradle, insert the lower end of the headset into the clip or car cradle (12), and connect the charger cable to the charger connector on the clip or cradle (13).The red indicator light is displayed during charging. Charging the battery fully may take up to 2 hours.3. When the battery is fully charged, the green indicator light is displayed. Disconnect the charger from the headset (or from the clip or car cradle), then from the wall outlet.When you unplug a charger, hold and pull the plug, not the cord.
ENGLISHThe fully charged battery has power for up to 5 hours of talk time. When you keep the headset in the clip or car cradle, the fully charged battery has power for up to 3 months of standby time. When you use the headset without the clip or cradle, the standby time is up to 100 hours.To check the battery charge when the headset is not connected to a charger, press the multifunction key when the headset is connected to a mobile device. If the indicator light is green, the charge level is sufficient. If the light is yellow, you may need to recharge the battery soon. If the light is red, recharge the battery.When the battery charge is low, the headset beeps every 5 minutes, the red indicator light flashes, and if voice prompts are activated, there is an audible notification. If voice prompts are activated, there is also an audible notification when the battery is completely discharged.Switch the headset onRemove the headset from the clip or car cradle. If the headset is not in the clip or cradle, press the multifunction key. The headset beeps, and the green indicator light flashes slowly while the headset tries to connect to the last or two last connected devices.When the headset is connected to at least one device and is ready for use, the blue indicator light flashes slowly. If the headset has not been paired with a device, it automatically enters pairing mode.Switch the headset offPlace the headset into the clip or car cradle, or press and hold the multifunction key for about 5 seconds. The headset beeps, and the red indicator light is briefly displayed.
ENGLISHIf the headset is not connected to a device within about 30 minutes, it switches off automatically.Pair and connect the headsetBefore using the headset, you must pair and connect it to a compatible device.You can pair the headset with up to eight devices, but you can connect it to a maximum of two devices at a time.To pair and connect the headset to a device:1. Make sure your mobile device is switched on and the headset is off.2. If the headset has not been previously paired with a device, switch on the headset. The headset enters pairing mode, and the blue indicator light starts to flash quickly.If the headset has been previously paired with a device, make sure the headset is switched off and not placed in the clip or car cradle, and press and hold the multifunction key for about 5 seconds until the blue indicator light starts to flash quickly.3. Within about 3 minutes, activate Bluetooth on your device, and set it to search for Bluetooth devices. For details, see the user guide of your mobile device.4. Select the headset from the list of found devices.5. If necessary, enter the passcode 0000 to pair and connect the headset to your device.In some devices, you may need to make the connection separately after pairing.
ENGLISHWhen the headset is connected to at least one device and is ready for use, the blue indicator light flashes slowly.To manually connect the headset to the last used device, press and hold the multifunction key for about 2 seconds (when no other device is connected), or make the connection in the Bluetooth menu of the device.You may be able to set your device so that the headset connects to it automatically. To activate this feature in a Nokia device, modify the paired device settings in the Bluetooth menu.Basic useChange the earpadThe headset may be provided with different sized earpads. Select the earpad that fits the best and is the most comfortable for your ear.To change the earpad, pull the current earpad from the earpiece, and push the new earpad into place (7).Place the headset on the earTo use the headset with the earloop, attach the earloop to it (11). To detach the earloop, gently pull it from the headset.You can rotate the earpad to keep the headset securely in the ear (8). For example, if you use the headset on the right ear, you may need to rotate the earpad to the right for the best fit. If you wear an earring, make sure it is not accidentally attached to the earpad.To place the headset on the ear, slide the earloop behind your ear (9), and gently push the earpiece against your
ENGLISHear. Point the headset towards your mouth (10).Store in the clip or car cradleWhen you do not keep the headset on your ear, store it in the clip or car cradle. When the headset is in the clip or cradle, it is switched off. When you remove the headset from the clip or cradle, the headset automatically switches on.To place the headset into the clip or cradle, slide the headset into place (14). To remove the headset, slide it out.Install the car cradleWhen you install the cradle in a car, make sure it does not interfere with or hinder the steering or braking systems or other systems used in the operation of the vehicle (for example, airbags) or disturb your field of vision while driving. Check that the deployment of the airbag is not blocked or impaired in any way.To install the car cradle, peel off the protective sheet from the cradle, and press the cradle against a flat surface so that it stays firmly in place. Do not install the cradle in a place where you might come in contact with it in the event of an accident or collision.Use the car cradleWhen you use the headset with the cradle in a car, obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety. Only operate the headset or car cradle if it is safe to do so under all driving conditions.Periodically check that the adhesive at the bottom of the car cradle is firmly attached, especially if the ambient temperature changes a lot. It is
ENGLISHrecommended that you do not leave the car cradle inside the vehicle in direct sunlight or in excessive heat.Adjust volumeThe headset automatically adjusts the volume according to ambient noise. To manually adjust the volume, use the volume controls of the connected device.The selected volume level is saved for the device that is currently connected to the headset.CallsTo make a call, use your mobile device in the normal way when the headset is connected to it.To redial the number you last called (if your mobile device supports this feature with the headset), when no call is in progress, press the multifunction key twice when the headset is not in the clip or car cradle.To activate voice dialling (if your mobile device supports this feature with the headset), when no call is in progress, press and hold the multifunction key for about 2 seconds when the headset is not in the clip or cradle. Proceed as described in the user guide of the mobile device.To answer a call, remove the headset from the clip or cradle. If the headset is not in the clip or cradle, press the multifunction key. To reject a call, press the multifunction key twice, or place the headset into the clip or cradle.To end a call, place the headset into the clip or cradle, or press the multifunction key when the headset is not in the clip or cradle.To switch a call between the headset and a compatible connected device, press and hold the multifunction key for about 2 seconds.
ENGLISHConnect to two devicesThe headset can be connected to two devices at the same time.Pair and connect to two devicesTo pair the headset with two devices, switch on the headset, activate pairing mode, and pair it with the first device. Switch off the headset, activate pairing mode, and pair it with the second device.To connect the headset to the two devices, switch the headset off and back on.Handle callsIf the headset can connect to two devices at the same time and you use redialling or voice dialling, the call is made on the device that you last used to make a call when the headset was connected to it.To answer a call on one connected device and end the active call on the other device, press the multifunction key.To answer a call on one connected device and put the active call on hold on the other device, press and hold the multifunction key for about 2 seconds.To end the active call on one connected device and make the call on hold active on the other device, press the multifunction key.To switch between the active call on one device and the call on hold on the other device, press and hold the multifunction key for about 2 seconds.Activate or deactivate voice promptsMake sure the headset is switched off and not placed in the clip or car cradle. Press and hold the multifunction key for about 5 seconds,
ENGLISHand press and hold the multifunction key again for about 2 seconds.When you activate the prompts, the green indicator light flashes once. When you deactivate the prompts, the yellow light flashes once. In both cases, there is also an audible notification.Clear pairingsTo clear the pairings from the headset, switch off the headset, and press and hold the multifunction key for about 8 seconds. The headset beeps twice, the red and green indicator lights alternate, and the headset enters pairing mode.TroubleshootingIf you cannot connect the headset to your compatible device, make sure the headset is charged, switched on, and paired with the device.Battery and charger informationThis device has an internal, nonremovable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. This device is intended for use when supplied with power from the following chargers: AC-3, AC-4, AC-5, AC-8, DC-4 and DC-9. The exact charger model number may vary depending on the type of plug. The plug variant is identified by one of the following: E, X, AR, U, A, C, K, or B. The battery can be charged and discharged hundreds of times, but it will eventually wear out.Talk and standby times are estimates only. Actual times are affected by, for example, device settings, features being used, battery condition, and temperature.
ENGLISHIf the battery has not been used for a long time, to begin charging, you may need to connect the charger, then disconnect and reconnect it.If the battery is completely discharged, it may take several minutes before the charging indicator is displayed.When your charger is not in use, unplug it from the electrical plug and the device. Do not leave a fully charged battery connected to a charger, as overcharging may shorten the battery's lifetime. If left unused, a fully charged battery will lose its charge over time.Always keep the battery between 15°C and 25°C (59°F and 77°F). Extreme temperatures reduce the capacity and lifetime of the battery. A device with a hot or cold battery may not work temporarily.Do not dispose of batteries in a fire as they may explode. Dispose of batteries according to local regulations. Recycle when possible. Do not dispose as household waste.Use the charger for its intended purpose only. Improper use or use of unapproved chargers may present a risk of fire, explosion, or other hazard, and may invalidate any approval or warranty. If you believe the charger is damaged, take it to a service centre for inspection before continuing to use it. Never use a damaged charger. Only use the charger indoors.Take care of your deviceHandle your device, charger and accessories with care. The following suggestions help you protect your warranty coverage.• Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode electronic circuits. If your
ENGLISHdevice gets wet, allow it to dry completely.• Do not use or store the device in dusty or dirty areas. Moving parts and electronic components can be damaged.• Do not store the device in high temperatures. High temperatures can shorten the life of the device, damage the battery, and warp or melt plastics.• Do not store the device in cold temperatures. When the device warms to its normal temperature, moisture can form inside the device and damage electronic circuits.• Do not attempt to open the device.• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and mechanics.• Only use a soft, clean, dry cloth to clean the surface of the device.• Do not paint the device. Paint can clog the moving parts and prevent proper operation.RecycleAlways return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you help prevent uncontrolled waste disposal and promote the recycling of materials. Check product environmental information and how to recycle your Nokia products at www.nokia.com/werecycle, or with a mobile device, www.nokia.mobi/werecycle.The crossed-out wheeled-bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies in the European Union. Do not dispose of these products as unsorted municipal
ENGLISHwaste. For more information on the environmental attributes of your device, see www.nokia.com/ecodeclaration.FCC/Industry Canada noticeThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: Changes or modifications not expressly approved by Nokia could void the user's authority to operate the equipment.

Navigation menu