Midland Radio WX80 Weather Alert Radio User Manual 2001073 WX 80
Midland Radio Corporation Weather Alert Radio 2001073 WX 80
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 145382 |
| Application ID | pZuQkShywfIjfssyb5m64A== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 46.36kB (579489 bits) |
| Date Submitted | 2001-04-17 00:00:00 |
| Date Available | 2001-04-27 00:00:00 |
| Creation Date | 2001-04-12 10:03:07 |
| Producing Software | Acrobat PDFWriter 4.05 for Windows |
| Document Lastmod | 2001-04-12 10:03:27 |
| Document Title | 2001073_WX-80 |
| Document Creator | 2001073.doc - Microsoft Word |
360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com MANUAL FCC Certification Report 2001073 / QRTL01-067 Topaz3, L.L.C. Page 14 of 25 FCC ID: O7KWX80 WX-80 Weather Monitor with SAME User Instruction Manual SPECIFICATIONS Number of Channels ……………………………… …………………… 7 Receiver Frequencies (MHz) Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 ……………… …………………………… … 162.550 ……………… …………………………… … 162.400 ……………… …………………………… … 162.475 ……………… …………………………… … 162.425 ………………… … ……………………… … 162.450 ……………… …………………………… … 162.500 ……………… …………………………… … 162.525 Receiving Sensitivity (at 12 dB SINAD)…………… …………… 0.3uV FIPS Code Sensitivity @ +/- 3KHz Deviation / 90% Success Rate………… …………… 0.3uV Signal to Noise Ratio ………… …………………… ……………… 40dB Dual Tone Detection Range………………………… ……1 .2 to 2.4 KHz Channel Selectivity ………………………………… …+ /- 25 KHz, 60dB Power Output (Maximum) ………………………… ……………250mW Battery Back-up ………… ………………………… …O n e 9-Volt Battery Antenna ………………… …………………… Telescoping Rod Antenna Dimensions(HWD) ………………………………… ……… Weight …………………… ………………………… ……… POWERING THE WEATHER RADIO Your Weather radio uses standard 12VDC power for normal operation and one 9V battery (not supplied) for backup power when standard power fails or is temporarily disconnected. For the best performance and longest life, we recommend an alkaline battery. Cautions: Use only a fresh battery of the required size and recommended type. Do not use a rechargeable battery in your Weather radio. Notes: A fresh backup battery will power the Weather radio for up to 1 hour with the weather broadcast turned on or up to 8 hours in alert standby mode. However, we recommend you always connect the Weather radio to AC power for normal use. If the backup battery becomes weak, your Weather radio might not sound a tone when an emergency or test alert is broadcast. When your radio’ s reception periodically, and replace the battery if the tone does net sound. Connecting the Weather radio to AC Power 1. If the Weather radio’ s display is on, shift the power switch to the right side until it clicks to turn off the Weather radio. 2. Connect the DC 12V Out of the power ADAPTOR to Weather radio’ s DC IN Power Jack. 3. Plug the Weather radio’ s DC power ADAPTOR into a standard AC outlet. Installing the Backup Battery 1. If the Weather radio’ s display is on, shift power switch to the right side until it clicks to turn off the Weather radio. 2. Press the tab on the battery compartment cover then lift up the cover to remove it. 3. Snap a 9V battery onto the battery terminals inside the compartment, then place the battery inside the compartment. 4. Replace the cover. When REPLACE then BATTERY appears or the Weather radio stops operating when it is unplugged from AC power, replace the battery. Note: REPLACE then BATTERY also appears it no backup battery is installed and the Weather radio is connected to AC power and then turned on. Caution: Dispose of an old battery promptly and properly. Do not burn or bury it. Always remove an old or weak battery. Batteries can leak chemicals that can destroy electronic parts. USING THE BUIL-IN ANTENNA The Weather radio’ s built-in telescoping antenna lets you receive strong local signals. To use the built-in antenna, lift it up so it is vertical then fully extend it. To improve reception in remote areas, you can connect an external antenna to your Weather radio using an optional adapter cable with a phone plug to the Weather radio’ s EXT ANT jack. Your local TOPAZ store sells a wide variety of antennas. To connect an external antenna to the Weather radio, connect one end of the adapter cable to EXT NAT on the back of the Weather radio then connect the other end to the antenna. PROGRAMMING THE WEATHER RADIO The first time you use your Weather radio, it is automatically set to use the NOAA weather broadcast frequency 162.550 MHz (Channel 1) and receive all SAME alert signals broadcast within a 50-mile radius of where you installed it. Your Weather radio is preprogrammed to receive broadcast for the FIPS code stored in first memory location (called single mode), and is preprogrammed with the seven national NOAA broadcast frequencies ( Channels 1-7). Depending on your location, you might need to set it to its multiple mode and select a different channel. Follow these steps to select a different broadcast frequency and set the Weather radio to its single or multiple mode (if necessary), and store or change FIPS codes in the Weather radio’ s memory (to narrow the area for which you receive SAME alerts). 1. To turn on the Weather radio, shift the power switch to the left side until it clicks. 2. Push the “Off” key for 2 second to Set MODE to PROFRAM. The Weather radio displays the last selected weather broadcast channel and frequency number. 3. Press WEATHER if necessary to turn on the weather broadcast, then push the VOLUME Up or Down Key so you can hear the broadcast as you make your selection. Note: If you do not press a key for about 45 seconds during Steps 4-8, the Weather radio exits the programming made and saves only those changes stored before the last key press. To continue, start over at Step2. 4. Press a number key (1-7) to listen to the broadcast on that channel. The Weather radio displays the selected channel and its corresponding frequency. Repeat this step until you find the channel broadcasting in your area. Note: If you receive a NOAA broadcast on more than one channel, the one with the Best reception might not be the one broadcasting information for your location. Contact your local TOPAZ store or the NWS to find out which frequency NOAA is using to broadcast from the station nearest your location, then select that channel. Channel Frequency(MHz) 162.550 162.400 162.475 162.425 162.450 162.500 162.525 5. Press “Yes” key three times. The currently selected mode (SINGLE or MULTIPLE) appears. 6. To select the other setting (SINGLE or MULTIPLE), press “No”. The setting you selected appears. 7. Press “Yes”. The FIPS code stored in the first memory location appears. 8. To change the code in the first memory location, press “No” key. ------- appears. Or, to add or change a code in a different position, repeatedly press “Yes” key Until you see the first unused memory location or the code you want to change, then press “No” key. -------- appears. 9. Use the number keys (0-9) to enter the 6-digit FIPS code you want to store. Note: If you make a mistake while entering the code press “No” to clear all digits ---- reappears ), then enter the correct digit. To reset the Weather radio to receive all SAME signals within a 50-mile radius, simply enter 99 in the first memory location. For easy reference, use a pencil to write down each FIPS code you store in memory on the supplied label. Then affix the label behind the Weather radio’ s back cover. ( -- 10. Press “Yes” key to store the code in the Weather radio’ s memory. If you set the Weather radio to its multiple mode the code (if any) stored in the next memory position appears. Repeat Steps 7-9 for each code (up to 15) you want to change or add. Note: when you press “Yes” key to store a code in the last (15th) memory position, weather alert descriptions appear 11. When you finish, Push the “Off” key for 2 second to Set MODE to OPERATE. The current alert status appears . TESTING THE WEATHER RADIO For your Weather radio to be effective, you must place it where it can receive an emergency alert broadcast and where you can hear its alert tone. In the United State, the NWS broadcast a test alert every week on Wednesday between 11 AM and 1 PM . To find out the specific test schedule in your area, contact your local NOAA or NWS office. These offices are usually listed in the telephone book under “US Government, Department of Commerce.” Important: The fact that you get clear reception of a weather broadcast signal does not guarantee that an emergency alert broadcast will trigger your Weather radio’ s alert function. Be sure you choose the proper location for the Weather radio and regularly check the Weather radio to be sure it is operating properly. Manually Testing the Alert Tone To manually test the Weather radio’ s alert tone, turn on the Weather radio, hold down OFF, turn on the Weather radio by shift the power switch to the left until it clicks then press ALERT. The Weather radio sounds the alert tone. Then, as the tone sounds, walk around the area where you keep the Weather radio to make sure you can hear the tone. Important Notes: To make sure your Weather radio will sound the alert tone when it receives an emergency signal always keep the built-in antenna fully extended. l Testing the alert tone only ensures that the Weather radio’ s alert tone can be heard. It does not test the Weather radio’ s receiver or guarantee you will receive an emergency alert. If the Weather radio does not sound an alert tone you are either out of rang of the broadcast or the backup battery is week. An emergency alert broadcast might not trigger your Weather radio’ s alert tone, even if it receives voice transmission clearly or if the alert tone sounds when you manually test it. Also, if you are in a fringe area, your Weather radio might be triggered by a broadcast when it is placed in one area, but not be triggered if you place it somewhere else (even close by). To turn on the Weather radio, shift the power switch to the left until it clicks. WEATHER then ALRT (alert) ON appears. Note: VOLUME also controls the Weather radio’ s audio broadcast volume. To set, the alert volume, see “Setting the Alert volume” Section. To listen to a Weather broadcast, see “Listening to a Weather Broadcast.” To have to a weather radio sound an alert, see “Using the Alert Function” To turn off the Weather radio, shift the power switch to the right until clicks and the display clears. LISTENING TO A WEATHER BROADCAST Your Weather radio is preprogrammed with the seven NOAA weather broadcast frequencies (Channels 1-7). To select a frequency broadcast in your area, follow Steps 2-4 and 9 in “Programming the Weather radio” To listen to a weather broadcast, make sure MODE is set to OPERATE, press WEATHER, then adjust VOLUME to the desired listening level. To turn off the weather broadcast, press WEATHER again. USING THE ALERT FUNCTION To set the Weather radio to sound an alert when the NWS broadcasts a warning, watch, or statement, hold down ALERT for 2 seconds until WEATHER then ALERT ON appears. The Weather radio beeps once. Note: If you programmed more than one FIPS code into memory, be sure the Weather radio is set to its multiple mode (see Steps 5 and 6 under “Programming the Weather radio”). Otherwise, the Weather radio will only receive broadcast for the FIPS code you stored in the first memory position. If severe weather threatens, do not wait for an alert tone; turn on the weather broadcast and monitor the weather information. To set the Weather radio so it does not sound an alert, hold down ALERT for 2 seconds until WEATHER ALERT OFF appears. The weather radio beeps twine. Setting the Alert Volume To Control alert or tone volume, Press “ Yes Key” for 2 seconds. In this case the “volume Up/Down” will be used for tone volume control and tone volume level will be displayed on LCD with beep tone on speaker. 10 Changing/Checking the Alert Pattern You can set the Weather radio to respond to an NWS alert broadcast in one of two ways. VOICE – the Weather radio sounds an alert for about 8 seconds, then automatically turns on the weather (voice) broadcast for 5 minutes. Then it returns to standby mode. It also displays the alert description (such as TORNADO WARNING) until the alert’ s effective time received as part of the NWS broadcast code expires. An alert could be in effect for several hours. (Continuous) ALERT – the Weather radio sounds an alert and displays an alert description until the alert’ s effective time expires. To turn off the alert sooner, press OFF. To turn on the NWS voice broadcast, press WEATHER. Note : When the Weather radio’ s alert ends or you turn it off, you hear the NWS alert tone(which sounds different than the Weather radio’ s tone) for a few seconds before you hear the voice broadcast. The Weather radio automatically selects the ALERT setting the first time you turn it on. To change the alert pattern setting (or check which setting is currently selected), follow these steps. 1. Push the “OFF” key for 2 seconds to set MODE to PROGRAM Note : If you do not press a key for about 45 seconds during Step 2 ~ 4, the Weather radio exits the programming mode without storing any change. To continue, start over at Step 1. 2. Press “Yes” Key once. The currently selected alert pattern (VOICE or ALERT) appears. 3. To select the other setting (VOICE or ALERT), press “No” Key. The setting you selected appears. 11 4. Press “ Yes” key again to store your selection, then Push the “OFF” key for 2 seconds to set MODE to OPERATE. The current alert status (WEATHER ALRT ON or WEATHER ALRT OFF) appears. Enabling/Disabling Alert Tones You can turn on or off some types of alert tones received by your Weather radio. For example, you can turn off the alert tone for avalanche watch if you do not live near an avalanche. Notes : The Weather radio still detects and displays information about alerts even after you disable the tone for those alerts. If you set the Weather radio so it turns itself on when it receives a specific warning, disabling the alert tone for that warning also means that the Weather radio will not turn itself on when it receives that warning. You can set the Weather radio so it does not sound an alert tone during only the following types of alerts: Avalanche Warning Avalanche Watch Blizzard Warning Coastal Flood Warning Coastal Flood Watch Flash Flood Statement Flash Flood Warning Flash Flood Watch Flood Statement Flood Warning Flood Watch High Wind Warning High Wind Watch Hurricane Statement Hurricane Watch Practice/Demo Required Monthly Test Severe Thunderstorm Watch Severe Weather Statement Special Marine Warning Special Weather Statement Test Message Unknown Statement Unrecognized code ending in S Volcano Warning Volcano Watch Winter Storm Warning Winter Storm Watch 12 When you decide it the alert tone will be on or off toward each of weather situation, current status for alert tone will be showing so as to adjust necessary type of alert only. In other words, you can turn on or off some type of alert tone by pressing “NO” Key, after checking current status for alert tone to specific warnings. To save your selection for current status for alert tone (ON or OFF), you should press “YES” Key and then you can check other alert tone status for weather after storing your selection. (Example) Alert Tone for Winter Storm Warning Owing to the space on LCD, LCD will show as follow, Severe Thunder Watch Tone On/Off No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) Yes Severe Weather Tone On/Off Yes No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes Special Weather Tone On/Off No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) No Yes No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes Flood Tone On/Off No Yes Yes Flood Warning Tone On/Off No Yes Yes Flood Watch Tone On/Off No Yes Yes Flash Flood Tone On/Off No Yes Yes Flash Flood Warning Tone On/Off No Yes Yes Flash Flood Watch Tone On/Off No No Yes No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes Yes 14 No Winter Storm Watch Tone On/Off No Yes Winter Storm Warning Tone On/Off No No No No Yes No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) No Yes No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) No Yes No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) No Yes No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes Coastal Flood Warning Tone On/Off Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes Coastal Flood Watch Tone On/Off No Yes Yes Hurricane Tone On/Off Change Tone State (Tone On > Tone Off , Tone Off > Tone On) Yes Hurricane Watch Tone On/Off No Yes Yes High Wind Warning Tone On/Off Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes High Wind Watch Tone On/Off No Yes Yes Blizzard Tone On/Off Change Tone State (Tone On > Tone Off , Tone Off > Tone On) No Yes No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes Yes 15 No Special Marine Warning Tone On/Off No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) Yes Avalanch Watch Tone On/Off Yes No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes Avalanch Warning Tone On/Off No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) No Change Tone State (Tone On > Tone Off , Tone Off > Tone On) No Yes No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes Demo Message Tone On/Off No Yes Yes Unkown Statement Tune TV Tone On/Off No Yes Yes Message Test Tone On/Off No Yes Yes Monthly Test Tone On/Off No Yes Yes Volcano Warning Tone On/Off No Yes Yes Volcano Watch Tone On/Off No No Yes No Change Tone State (Tone On > Tone Off , Tone On > Tone Off) Yes Yes 16 No Using the Weather radio’ s ‘ All Signals’ Code Your Weather radio is preset to use a default “all signals” code of 99, which lets it receive any weather alert broadcast within its reception range (about a 50-mile radius in most locations). This code is preset in the Weather radio’ s first memory location. To set the Weather radio to respond only to specific NWS FIPS codes you select, choose the codes (as many as 15) you want to program, program those codes into memory locations 2 ~ 15, and set the Weather radio to its multiple mode. To reset the Weather radio to use the “all signals” code again, follow the steps under “Programming the Weather Radio” section, setting the Weather radio to its single mode in Steps 5 and 6 and storing 99 in the first memory position in Step 9. Reviewing Overlapping Alerts Your Weather radio can store up to three different alerts (with overlapping effective times) in its memory. If the Weather radio receives a new alert while a previous alert is still in effect, it automatically displays the alert description and sounds an alert for the new alert. To scroll forward or backward through the Weather radio’ s memory and review all effective alerts, press “Yes” (to scroll backward). Notes: The Weather radio sounds a high-pitched tone if you try to scroll past the first or last alert in memory. To continue, press “Yes” key to begin scrolling in the opposite direction If the Weather radio receives a new alert while three previous alerts are still in effect, it stores the newest alert and clears the oldest alert from memory. 17 When a Test or Demo Alert Occurs The NWS sends out weekly test signals, you can use to confirm that your Weather radio is working properly. To find out the specific test schedule in your area, contact your local NOAA or NWS office. Those offices are usually listed in the telephone book under US Government, Department of Commerce. When the Weather radio’ s alert function is turned on and the Weather radio receives a test broadcast for a FIPS code you programmed into its memory, it responds in one of these ways: NWS Alert Type Demo Message (sent at random times) Required Weekly SAME Test Required Monthly SAME Test You See You Hear Demo Message No sound Weekly Test Beeps Monthly Test Beeps Note : The Weather radio does not turn on an indicator during a test/demo broadcast. LOCKING OUT UNDEFINED WEATHER DESCRIPTIONS The NWS might occasionally broadcast several types of weather information intended for commercial or other non-private use. This information could include, for example, messages intended for automated weather services (such as those used by radio or TV stations). Your Weather radio’ s memory does not contain a specific, corresponding description for the signals related to these commercial weather types. 18 Additionally, your Weather radio is designed to recognize all common weather alert types currently used by the NWS. The NWS could, however, eventually create and broadcast new alert types (for which the Weather radio’ s memory does not contain a specific, corresponding description). If your Weather radio receives a signal for a new alert type, it is preset (if the alert function is turned on) to display UNKNOWN, the alert description (EMERGENC, STATEMNT, WARNING, or WATCH), and TUNE TV, then sound a siren alert. It is not set to alert you when it receives a commercial alert type. Depending on your preference, you can follow these steps to change the way the Weather radio responds to new weather alert broadcasts. 1. Turn off the Weather radio. 2. While holding down OFF, Shift power switch to the left side until it clicks to turn on the Weather radio. TESTMODE appears. 3. Press a number key to select the desired setting. The Weather radio tunes to the corresponding channel, and one of the following appears. You Press : The Weather radio Displays : CH. 1 CH. 2 CH. 3 CH. 4 CH. 5 CH. 6 CH. 7 DEFAULT (reset to default) DEMO ON or DEMO OFF (the Weather radio’ s demo mode 19 Note : If you pressed 9 in this step, your Weather radio can also perform these test functions while TESTMODE appears: If you press ALERT, the Weather radio continuously sounds its alert siren. Press ALERT again to turn off the siren. If you press YES, STATEMENT, WATCH, and WARNING light at the same time. If you press NO, STATEMENT, WATCH, and WARNING turn off at the same time. If you press WEATHER, all display characters appear at the same time. 4. Shift power switch to the right side until it clicks to turn off the weather radio and store your selection. Then turn it back on to begin using the new setting. USING THE BACKLIGHT Your Weather radio’ s backlight automatically turns on while you listen to the weather broadcast and for about 10 seconds each time you press a key. For extended use in low light situations, you can set the backlight so it remains on until you turn it off. Note : You can turn on your Weather radio’ s backlight so it stays on continuously only if the Weather radio is connected to AC power through DC Adapter. Follow these steps to turn the backlight on or off. 1. Push the “OFF” key for 2 seconds to set MODE to PROGRAM. 2. Within 45 seconds, press “Yes” key twice so CONTINUO (continuous) and BACKLITE alternately flash on the display, then press “Yes” key to turn on continuous backlight or “No” key to turn it off. 20 Note : If you do not press a key for about 45 seconds, the Weather radio automatically exits the programming mode. 3. Push the “OFF” key for 2 seconds to set MODE to OPERATE. 21 UNDERSTANDING FIPS CODES For the purpose of broadcasting weather information, the NWS has divided the United States into regions by state and county (or parish, where applicable) then assigned a 6-digit FIPS code to identify each county or parish. For example, the code for Dallas County, Texas, is 048113. The first digit in a FIPS code identifies the county subdivision, the next two digits identify the state, and the last three digits identify the county or parish. Note: Most FIPS codes begin with 0, which means that FIPS code represents an entire county. The NWS, however, eventually plans to subdivide some large counties. When that happens, each subdivision will be assigned a digit from 1~9, resulting in codes such as 148113, 248113, and so on. Your Weather radio can receive all SAME alert signals broadcast within about a 50-mile radius of where you installed it. To receive SAME alerts and broadcasts about weather occurring only in particular Counties, within that area, you can program up to 15 FIPS codes into the Weather radio’ s memory. For example, this lets you avoid hearing an alert that applies to an area within a 50-mile radius but not necessarily to your county or parish. Obtaining Your Area’ s FIPS Code(s) To obtain the FIPS code for the location where you installed your Weather radio, contact your local TOPAZ store or call the NWS toll free at 1-888-NWR-SAME (1-888697-7263). If you call the NWS, follow the instructions you hear. Note: If you are close to a county or parish line, you might want to obtain the codes for the nearby counties or parishes. Hint: Since you can program up to 15 FIPS codes into the Weather radio’ s memory, you might want to obtain the codes for other local areas that you frequently travel through (as long as those areas are within a 50 mile radius of your location and within an area 22 covered by your local NWS broadcast station). That way, you can program those codes into the Weather radio and receive broadcasts covering those locations, too. NWS WEATHER ALERT DESCRIPTION Your Weather radio can display these NWS weather alert descriptions. For easy reference, this list also shows the type of alert (siren or beep) that sounds during each alert. Weather/Alert You See You Hear Description Avalanche warning Siren AVALANCH WARNING Avalanche watch Siren AVALANCH WATCH Blizzard warning Siren BLIZZARD WARNING Civil danger warning Siren CIVIL DANGER WARNING Civil danger watch Siren CIVIL DANGER WATCH Civil emergency-turn on the TV for information is available on Siren TUNE TV TV, call your local NWS office Note: TUNE TV might also indicate the Weather radio has received a signal for a condition not defined the Weather radio’ s memory (See “Locking Out Undefined Weather Descriptions”) Coastal flood warning Siren COASTAL FLOOD WARNING Coastal flood watch Siren COASTAL FLOOD WATCH Emergency action warning Siren EMERGENC ACTION WARNING Emergency action termination Siren EMERGENC ACTION TERMINAT Evacuate immediately Siren EVACUATE IMMEDIAT Fire warning Siren FIRE WARNING Flash flood statement Beeps FLASH FLOOD Flash flood warning Siren FLASH FLOOD WARNING Flash flood watch Siren FLASH FLOOD WATCH Flood statement Beeps FLOOD Flood warning Siren FLOOD WARNING Flood watch Siren FLOOD WATCH Hazardous material warning Siren HAZARD MATERIAL WARNING Hazardous material watch Siren HAZARD MATERIAL WATCH High wind warning Siren HIGH WIND WARNING 23 High wind watch Hurricane statement Hurricane warning Hurricane watch Immediate evacuation warning Law enforcement warning Local area emergency National information Center Periodic national test Practice/Demo Radiological hazard warning Radiological hazard watch Required monthly test Required weekly test Severe thunderstorm warning Severe thunderstorm watch Severe thunderstorm statement Shelter in-place warning Special marine warning Special weather statement Test message Tornado warning Tornado watch Tsunami warning Unrecognized code ending in S Unrecognized code ending in W Unrecognized code ending in A Unrecognized code ending in E Volcano warning Volcano watch Winter storm warning Winter storm watch HIGH WIND WATCH HURRICAN HURRICAN WARNING HURRICAN WATCH IMMECIAT EVACUATE WARNING LOW ENFORCE WARNING LOCAL AREA EMERGENC NATIONAL INFO CENTER NATIONAL PERIODIC TEST DEMO MESSAGE RADIOLOG HAZARD WARNING RADIOLOG HAZARD WATCH MONTHLY TEST WEEKLY TEST SEVERE THUNDER WARNING SEVERE THUNDERWATCH SEVERE WEATHER SHELTER IN-PLACE WARNING SPECIAL MARING WARNING SPECIAL WEATHER TEST MESSAGE TORNADO WARNING TORNADO WATCH TSUNAMI WARNING UNKNOWN STATEMNT TV UNKNOWN WARNING TUNE TV UNKNOWN WATCH TUNE TV UNKNOWN ENERGENC TUNE TV VOLCANO WARNING VOLCANO WATCH WINTER STORM WARNING WINTER STORM WATCH 24 Siren Beeps Siren Siren Siren Siren Siren Siren Siren Nothing Siren Siren Beeps Beeps Siren Siren Beeps Siren Siren Beeps Nothing Siren Siren Siren Siren Siren Siren Siren Siren Siren Siren Siren
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Modify Date : 2001:04:12 10:03:27-04:00 Create Date : 2001:04:12 10:03:07-04:00 Title : 2001073_WX-80 Creator : 2001073.doc - Microsoft Word Producer : Acrobat PDFWriter 4.05 for Windows Page Count : 25EXIF Metadata provided by EXIF.tools