Miele and Cie KG EK037 WLAN Module User Manual Miele EHS Device Specification

Miele & Cie. KG WLAN Module Miele EHS Device Specification

user manual

Miele@home Manual for EK037 USA/CDN Market Version 1.3
Manual for EK037 USA/CDN Version: 1.3 EK037 WiFi Module Date: 20/09/2016 Manual_EK037_USA_CDN_1.3.docx  2015 Miele&Cie. KG Page 2 of 7 Revision History Date Version Description Author Department 03.09.2015 1.0 Draft Initial manual for FCC/IC F. Laube GTE/SKT 10.06.2016 1.1 Little Changes F. Laube GTE/DPS 15.09.2016 1.2 Final Changes Chr. Bömke GTE/DPS 20.09.2016 1.3 Integration Changes L. Merkel GTE/DPS Reviewed By Date Version Name Department 09.09.2014 1.0 Draft G. Borgelt GTE/TL 15.09.2016 1.2 G. Borgelt L. Merkel GTE/TL GTE/DPS 20.09.2016 1.3 G. Borgelt GTE/TL Approvals Date Version Name Department
Manual for EK037 USA/CDN Version: 1.3 EK037 WiFi Module Date: 20/09/2016 Manual_EK037_USA_CDN_1.3.docx  2015 Miele&Cie. KG Page 3 of 7 Contents 1. General 4 2. Technical data EK037 4 3. Norms / Standards 5 3.1 FCC / IC 5 3.2 Safety 5 3.3 RF-Standard 5 3.4 Photos and Labels 6 4. Regulatory Notice and Integration 6 4.1 United States (FCC Notice) 6 4.2 Canada (IC Notice) 7 4.3 Integration 7
Manual for EK037 USA/CDN Version: 1.3 EK037 WiFi Module Date: 20/09/2016 Manual_EK037_USA_CDN_1.3.docx  2015 Miele&Cie. KG Page 4 of 7 1. General The EK037 is a wireless network interface module for Miele domestic appliances like hoods, hobs, cooling devices or washing machines. The module supports the IEEE 802.11 b/g/n Wifi standard. The EK037 module is designed to solder on PCB during manufacturing. The Module will only be used in Miele domestic appliances. 3,3V Voltage Regulator inside the SoC)SingleChipWIFI TransceiverPCB-Antenna with antenna-NetworkHome appliance Interface3,3VEK037Crystal40MHzCrystal32.768 kHz Operational Description The EK037 is based on CC3200 WiFi SOC Controller and has a board design in stamp form factor. The Chip controls the IEEE 802.11 RF and handles the WiFi and IP stack. The Chip also handles the connection to the domestic appliance via a serial link and Miele protocol. Integration instruction The EK037 must be integrated under consideration of the technical data. It is not allowed to make any changes on the module or to use another antenna. The module should be placed in an area with good RF performance. 2. Technical data EK037 VCC in V 3,0 min. 3,3 typical 3,6 max. Current in mA 200 typical 330 max. ambient temperature in°C 0 – 75 0 – 85 SoC Humidity max 90% non condensation Dimensions in mm 30/27 Wireless MCU/RF IC CC3200r1 Input double buffered interface (CC3200r1) Antenna type PCB inverted F Antenna gain 2 dB Crystal Input Clock 32.768 kHz 40 MHz RF Frequency 2.45 GHz Channels 1 to 11 Channel Frequencies 2,412 GHz – 2,462 GHz Transmission Power in mW <100
Manual for EK037 USA/CDN Version: 1.3 EK037 WiFi Module Date: 20/09/2016 Manual_EK037_USA_CDN_1.3.docx  2015 Miele&Cie. KG Page 5 of 7 Footprint 3. Norms / Standards 3.1 FCC / IC FCC Regulation Part 15.109, Part 15.209 and Part 15.247 IC regulations RSS-Gen Issue 4 and RSS-247 3.2 Safety UL 60730-1A, CAN/CSA E60730-1:02+A1:2007 CSA Certificate 70009686 3.3 RF-Standard The modules use the RF standard IEEE 802.11 b/g/n20
Manual for EK037 USA/CDN Version: 1.3 EK037 WiFi Module Date: 20/09/2016 Manual_EK037_USA_CDN_1.3.docx  2015 Miele&Cie. KG Page 6 of 7 3.4 Photos and Labels EK037 Top View 4. Regulatory Notice and Integration 4.1 United States (FCC Notice) FCC ID: 2ACUWEK037 In accordance with FCC Part 15, the 2ACUWEK037 is listed as a Modular Transmitter Device. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that cause undesired operation. FCC STATEMENT: This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver
Manual for EK037 USA/CDN Version: 1.3 EK037 WiFi Module Date: 20/09/2016 Manual_EK037_USA_CDN_1.3.docx  2015 Miele&Cie. KG Page 7 of 7 • Connect the equipment into an outlet on a different circuit from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help. USERS MANUAL OF THE END PRODUCT: The end user has to be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the user’s manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following “Contains FCC ID: 2ACUWEK037 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 4.2 Canada (IC Notice) IC: 5669C-EK037 The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. LABEL OF THE END PRODUCT The final end product must be labeled in a visible area with the following “Contains IC : 5669C-EK037". This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 4.3 Integration This EK037 Module will only be integrated on our responsibility into Miele appliances/endproducts. The final products, including the integrated radio module, have to show compliance to the FCC /IC requirements. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification, Doc) of the final endproducts will be addressed by Miele & Cie. KG.

Navigation menu